ASTM F2075-10a
(Specification)Standard Specification for Engineered Wood Fiber for Use as a Playground Safety Surface Under and Around Playground Equipment
Standard Specification for Engineered Wood Fiber for Use as a Playground Safety Surface Under and Around Playground Equipment
ABSTRACT
This specification covers engineered wood fiber for use as a playground safety surface under and around playground equipment. This specification establishes minimum requirements for the factors that determine particle size, consistency, purity, ability to drain, and heavy metal concentrations considered hazardous to children. This specification does not imply that an injury cannot be incurred if the engineered wood fiber complies with this specification. The performance requirements for (1) sieve test analysis, (2) hazardous metal test (for antimony, arsenic, barium, cadmium, chromium, lead, mercury, and selenium), and (3) magnetic and nonmagnetic tramp metal tests are specified. The sieve test apparatus shall include balances, sieves, sieve shaker, and oven. The test apparatus for hazardous metal test shall include metal sieve, pH, membrane filter, reagents, hydrochloric acid solution, Type 3 water, centrifuge, and container. The test apparatus for magnetic tramp metal test shall be an industrial grade magnetic wand with a cylindrical neodymium iron-boron rare earth magnet at the end of the probe. A schematic diagram of the magnetic probe is provided. The sampling method, sample test preparation, test procedure, and test report for the three test methods are detailed.
SCOPE
1.1 This specification establishes minimum characteristics for those factors that determine particle size, consistency, purity, and ability to drain.
1.2 Engineered wood fiber that meets the requirements of this specification must comply with Specification F1292, if the surface is in the use zone as defined in Specification F1487.
1.3 A sample of wood fiber that meets the requirements of this specification may be designated engineered wood fiber and be suitable for playground safety surfacing.
1.4 This specification does not imply that an injury cannot be incurred if the engineered wood fiber complies with this specification.
1.5 To meet the requirements of this specification, the material shall perform as follows:
1.5.1 The material shall meet particle size requirements.
1.5.2 The material shall meet the requirement for metal particles.
1.5.3 The material shall meet the allowable heavy metal concentrations considered hazardous to children.
1.5.4 The material shall meet the requirements of Specification F1292.
1.6 The values stated in inch-pound units are to be regarded as standard. The values in parentheses are mathematical conversions. SI units, which are provided for information, are not considered the standard, except in 8.4.
1.7 Warning—Mercury has been designated by EPA and many state agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury-containing products. See the applicable product Material Safety Data Sheet (MSDS) for details and EPA’s website (http://www.epa.gov/mercury/faq.htm) for additional information. Users should be aware that selling mercury or mercury-containing products, or both, in your state may be prohibited by state law.
1.8 The following precautionary statement pertains to the test method portions only, in 7.4, 8.4, and 9.4 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F2075 −10a AnAmerican National Standard
Standard Specification for
Engineered Wood Fiber for Use as a Playground Safety
1
Surface Under and Around Playground Equipment
This standard is issued under the fixed designation F2075; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
Theneedforasystematicmeansofevaluatingengineeredwoodfiberforuseasaplaygroundsafety
surface from the standpoint of particle size, consistency, purity, and ability to drain, has become a
growing concern of the designers, operators, and manufacturers of engineered wood fiber systems.
There has been no qualitative method to assess these parameters of engineered wood fiber (that is,
particle size, consistency, purity, and ability to drain) to ensure its quality. Therefore, the goal of this
specification is to establish a uniform means to measure the characteristics of engineered wood fiber
in order to provide the potential buyer with performance specifications to select an engineered wood
fiber suitable to meet the needs of playground designers, operators and manufacturers.
1. Scope conversions. SI units, which are provided for information, are
not considered the standard, except in 8.4.
1.1 This specification establishes minimum characteristics
for those factors that determine particle size, consistency, 1.7 Warning—Mercury has been designated by EPA and
purity, and ability to drain. many state agencies as a hazardous material that can cause
central nervous system, kidney, and liver damage. Mercury, or
1.2 Engineered wood fiber that meets the requirements of
its vapor, may be hazardous to health and corrosive to
this specification must comply with Specification F1292,ifthe
materials.Cautionshouldbetakenwhenhandlingmercuryand
surface is in the use zone as defined in Specification F1487.
mercury-containing products. See the applicable product Ma-
1.3 A sample of wood fiber that meets the requirements of
terial Safety Data Sheet (MSDS) for details and EPA’s website
thisspecificationmaybedesignatedengineeredwoodfiberand
(http://www.epa.gov/mercury/faq.htm) for additional informa-
be suitable for playground safety surfacing.
tion. Users should be aware that selling mercury or mercury-
1.4 This specification does not imply that an injury cannot containingproducts,orboth,inyourstatemaybeprohibitedby
state law.
be incurred if the engineered wood fiber complies with this
specification.
1.8 The following precautionary statement pertains to the
test method portions only, in 7.4, 8.4, and 9.4 of this specifi-
1.5 To meet the requirements of this specification, the
cation: This standard does not purport to address all of the
material shall perform as follows:
safety concerns, if any, associated with its use. It is the
1.5.1 The material shall meet particle size requirements.
responsibility of the user of this standard to establish appro-
1.5.2 The material shall meet the requirement for metal
priate safety and health practices and determine the applica-
particles.
bility of regulatory limitations prior to use.
1.5.3 The material shall meet the allowable heavy metal
concentrations considered hazardous to children.
2. Referenced Documents
1.5.4 The material shall meet the requirements of Specifi-
2
cation F1292.
2.1 ASTM Standards:
C136Test Method for Sieve Analysis of Fine and Coarse
1.6 Thevaluesstatedininch-poundunitsaretoberegarded
Aggregates
as standard. The values in parentheses are mathematical
D1193Specification for Reagent Water
1
This specification is under the jurisdiction ofASTM Committee F08 on Sports
Equipment, Playing Surfaces, and Facilities and is the direct responsibility of
2
Subcommittee F08.63 on Playground Surfacing Systems. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Aug. 1, 2010. Published September 2010. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 2001. Last previous edition approved in 2010 as F2075–10. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/F2075-10A. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2075−10a
D2217Practice for Wet Preparation of Soil Samples for 3.2.1 head injury criteria (HIC), n—a measure of impact
Particle-Size Analysis and Determination of Soil Con- severitythatconsidersthedurationoverwhichthemostcritical
stants section of the deceleration pulse persists as well as the peak
E11Specification forWovenWireTe
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:F2075–10 Designation: F2075 – 10a
Standard Specification for
Engineered Wood Fiber for Use as a Playground Safety
1
Surface Under and Around Playground Equipment
This standard is issued under the fixed designation F2075; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
The need for a systematic means of evaluating engineered wood fiber for use as a playground safety
surface from the standpoint of particle size, consistency, purity, and ability to drain, has become a
growing concern of the designers, operators, and manufacturers of engineered wood fiber systems.
There has been no qualitative method to assess these parameters of engineered wood fiber (that is,
particle size, consistency, purity, and ability to drain) to ensure its quality. Therefore, the goal of this
specification is to establish a uniform means to measure the characteristics of engineered wood fiber
in order to provide the potential buyer with performance specifications to select an engineered wood
fiber suitable to meet the needs of playground designers, operators and manufacturers.
1. Scope
1.1 This specification establishes minimum characteristics for those factors that determine particle size, consistency, purity, and
ability to drain.
1.2 EngineeredwoodfiberthatmeetstherequirementsofthisspecificationmustcomplywithSpecificationF1292,ifthesurface
is in the use zone as defined in Specification F1487.
1.3 A sample of wood fiber that meets the requirements of this specification may be designated engineered wood fiber and be
suitable for playground safety surfacing.
1.4 This specification does not imply that an injury cannot be incurred if the engineered wood fiber complies with this
specification.
1.5 To meet the requirements of this specification, the material shall perform as follows:
1.5.1 The material shall meet particle size requirements.
1.5.2 The material shall meet the requirement for metal particles.
1.5.3 The material shall meet the allowable heavy metal concentrations considered hazardous to children.
1.5.4 The material shall meet the requirements of Specification F1292.
1.6 The values stated in inch-pound units are to be regarded as standard. The values in parentheses are mathematical
conversions. SI units, which are provided for information, are not considered the standard, except in 8.4.
1.7 Warning—Mercury has been designated by EPA and many state agencies as a hazardous material that can cause central
nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution
should be taken when handling mercury and mercury-containing products. See the applicable product Material Safety Data Sheet
(MSDS) for details and EPA’s website (http://www.epa.gov/mercury/faq.htm) for additional information. Users should be aware
that selling mercury or mercury-containing products, or both, in your state may be prohibited by state law.
1.8 The following precautionary statement pertains to the test method portions only, in 7.4, 8.4, and 9.4 of this specification:
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the
user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations
prior to use.
1
This specification is under the jurisdiction of ASTM Committee F08 on Sports Equipment and Facilities and is the direct responsibility of Subcommittee F08.63 on
Playground Surfacing Systems.
´1
Current edition approved Jan. 15, 2010. Published February 2010. Originally approved in 2001. Last previous edition approved in 2004 as F2075–04 . DOI:
10.1520/F2075-10.
Current edition approved Aug. 1, 2010. Published September 2010. Originally approved in 2001. Last previous edition approved in 2010 as F2075 – 10. DOI:
10.1520/F2075-10A.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F2075 – 10a
2. Referenced Documents
2
2.1 ASTM Standards:
C136 Test Method for Sieve Analysis of Fine and Coarse Aggregates
D1193 Specification for Reagent Water
D2217 Practice for Wet Preparation of Soil Samples for Particle-Size Analysis
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.