ASTM D129-00(2005)
(Test Method)Standard Test Method for Sulfur in Petroleum Products (General Bomb Method)
Standard Test Method for Sulfur in Petroleum Products (General Bomb Method)
ABSTRACT
This standard details the general bomb test method for determination of the amount of sulfur in lubricating oils with additives, additive concentrates, lubricating greases, and other petroleum products with low volatilities. This test method entails oxidizing samples by combustion in a bomb containing oxygen under pressure. The amount of sulfur is determined by gravimetry. Materials needed for the test include a combustion bomb, sample cup, firing wire, ignition circuit, and a cotton wicking or nylon sewing thread. All reagents, samples, and other chemicals used for the test should conform to the required concentration and purity.
SCOPE
1.1 This test method covers the determination of sulfur in petroleum products, including lubricating oils containing additives, additive concentrates, and lubricating greases that cannot be burned completely in a wick lamp. The test method is applicable to any petroleum product sufficiently low in volatility that it can be weighed accurately in an open sample boat and containing at least 0.1 % sulfur.
Note 1—This test method is not applicable to samples containing elements that give residues, other than barium sulfate, which are insoluble in dilute hydrochloric acid and would interfere in the precipitation step. These interfering elements include iron, aluminum, calcium, silicon, and lead which are sometimes present in greases, lube oil additives, or additive oils. Other acid insoluble materials that interfere are silica, molybdenum disulfide, asbestos, mica, and so forth. The test method is not applicable to used oils containing wear metals, and lead or silicates from contamination. Samples that are excluded can be analyzed by Test Method D 1552.
1.2This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 3.2 for specific precautionary directions incorporated in the test method.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
British Standard 4454
Designation:D129–00 (Reapproved 2005)
Designation: 61/99
Standard Test Method for
1
Sulfur in Petroleum Products (General Bomb Method)
This standard is issued under the fixed designation D129; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This test method has been adopted for use by government agencies to replace Method 5202 of Federal Test Method No. 791b
1. Scope* D6299 Practice for Applying Statistical Quality Assurance
and Control Charting Techniques to Evaluate Analytical
1.1 This test method covers the determination of sulfur in
Measurement System Performance
petroleum products, including lubricating oils containing addi-
E144 Practice for Safe Use of Oxygen Combustion Bombs
tives, additive concentrates, and lubricating greases that cannot
be burned completely in a wick lamp. The test method is
3. Summary of Test Method
applicable to any petroleum product sufficiently low in vola-
3.1 The sample is oxidized by combustion in a bomb
tility that it can be weighed accurately in an open sample boat
containing oxygen under pressure. The sulfur, as sulfate in the
and containing at least 0.1 % sulfur.
bomb washings, is determined gravimetrically as barium sul-
NOTE 1—This test method is not applicable to samples containing
fate.
elements that give residues, other than barium sulfate, which are insoluble
3.2 Warning—Strict adherence to all of the provisions
in dilute hydrochloric acid and would interfere in the precipitation step.
prescribed hereafter ensures against explosive rupture of the
These interfering elements include iron, aluminum, calcium, silicon, and
bomb, or a blow-out, provided the bomb is of proper design
leadwhicharesometimespresentingreases,lubeoiladditives,oradditive
and construction and in good mechanical condition. It is
oils. Other acid insoluble materials that interfere are silica, molybdenum
disulfide, asbestos, mica, and so forth.The test method is not applicable to desirable, however, that the bomb be enclosed in a shield of
usedoilscontainingwearmetals,andleadorsilicatesfromcontamination.
steel plate at least 13 mm thick, or equivalent protection be
Samples that are excluded can be analyzed by Test Method D1552.
provided against unforseeable contingencies.
1.2 This standard does not purport to address all of the
4. Apparatus and Materials
safety concerns, if any, associated with its use. It is the
3,4
responsibility of the user of this standard to establish appro- 4.1 Bomb, having a capacity of not less than 300 mL, so
constructed that it will not leak during the test and that
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use. See 3.2 for specific quantitative recovery of the liquids from the bomb may be
achieved readily. The inner surface of the bomb may be made
precautionary directions incorporated in the test method.
of stainless steel or any other material that will not be affected
2. Referenced Documents
by the combustion process or products. Materials used in the
2
2.1 ASTM Standards: bomb assembly, such as the head gasket and lead-wire insula-
D1193 Specification for Reagent Water tion,shallberesistanttoheatandchemicalaction,andshallnot
D1552 Test Method for Sulfur in Petroleum Products undergo any reaction that will affect the sulfur content of the
(High-Temperature Method) liquid in the bomb.
4.2 Sample Cup, platinum, 24 mm in outside diameter at the
bottom, 27 mm in outside diameter at the top, 12 mm in height
1
outside, and weighing 10 to 11 g.
This test method is under the jurisdiction of ASTM Committee D02 on
Petroleum Products and Lubricants and is the direct responsibility of Subcommittee
4.3 Firing Wire, platinum, No. 26B&S gage, 0.41 mm (16
D02.03 on Elemental Analysis.
thou), 27 SWG, or equivalent. (Warning—The switch in the
Current edition approved May 1, 2005. Published May 2005. Originally
ignition circuit shall be of a type which remains open, except
approved in 1922. Last previous edition approved in 2000 as D129 – 00.
This test method was adopted as a joint ASTM-IP standard in 1964. when held in closed position by the operator.)
In the IP, this test method is under the jurisdiction of the Standardization
Committee. DOI: 10.1520/D0129-00R05.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
3
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Criteria for judging the acceptability of new and used oxygen combustion
Standards volume information, refer to the standard’s Document Summary page on bombs are described in Practice E144
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.