iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM C1232-23

(Terminology)

Standard Terminology for Masonry

Standard Terminology for Masonry

SCOPE
1.1 This standard incorporates generic terms and generic definitions of terms specifically associated with manufactured masonry units and masonry constructed with manufactured masonry units. These generic terms and definitions are used within the standards developed by Committee C12 on Mortars and Grouts for Unit Masonry and Committee C15 on Manufactured Masonry Units.  
1.2 This standard incorporates terms and definitions of terms associated with the standards specific to clay masonry units, in particular to Specifications C32, C34, C56, C62, C126, C212, C216, C279, C410, C530, C652, C902, C1088, C1167, C1261, C1272, and C1405, and to Test Methods C67/C67M.  
1.3 This standard incorporates terms and definitions of terms associated with the standards specific to concrete masonry units in particular to Specifications C55, C73, C90, C129, C139, C744, C1319, C1372, C1491, C1623, and C1634 and to Test Methods C140/C140M, C426, and C1262/C1262M.  
1.4 This standard incorporates terms and definition of terms associated with the standards specific to autoclaved aerated concrete masonry units in particular to Practice C1692 and to Specifications C1386, C1691, and C1693.  
1.5 This standard incorporates terms and definitions of terms associated with the standards specific to clay and concrete roofing tile units in particular to Specifications C1167 and C1492 and to Test Methods C1568, C1569, and C1570.  
1.6 For terminology specific to mortar and grout, see Terminology C1180.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
14-Dec-2023
ICS
01.040.91 - Construction materials and building (Vocabularies)
91.080.30 - Masonry
Technical Committee
C15 - Manufactured Masonry Units
Drafting Committee
C15.08 - Terminology
Current Stage
Ref Project

Relations

Replaces
ASTM C1232-21a - Standard Terminology for Masonry
Effective Date
15-Dec-2023
Referred By
ASTM C1088-23 - Standard Specification for Thin Veneer Brick Units Made From Clay or Shale
Effective Date
15-Dec-2023
Referred By
ASTM C62-23 - Standard Specification for Building Brick (Solid Masonry Units Made from Clay or Shale)
Effective Date
15-Dec-2023
Referred By
ASTM C1717-19 - Standard Test Methods for Conducting Strength Tests of Masonry Wall Panels
Effective Date
15-Dec-2023
Referred By
ASTM C1715/C1715M-22 - Standard Test Method for Evaluation of Water Leakage Performance of Masonry Wall Drainage Systems
Effective Date
15-Dec-2023
Referred By
ASTM C1716/C1716M-23 - Standard Specification for Compression Testing Machine Requirements for Concrete Masonry Units, Related Units, and Prisms
Effective Date
15-Dec-2023
Referred By
ASTM C1825-19 - Standard Guide for Developing Specifications for Masonry Units
Effective Date
15-Dec-2023
Referred By
ASTM C1791-16(2021) - Standard Guide for Reduction of Efflorescence Potential in New Unit Pavement Systems
Effective Date
15-Dec-2023
Referred By
ASTM C1790-21 - Standard Specification for Fly Ash Facing Brick
Effective Date
15-Dec-2023
Referred By
ASTM C1197-22 - Standard Test Method for In Situ Measurement of Masonry Deformability Properties Using the Flatjack Method
Effective Date
15-Dec-2023
Referred By
ASTM C1884-23a - Standard Specification for Manufactured Concrete Ballast Units
Effective Date
15-Dec-2023
Referred By
ASTM C139-23 - Standard Specification for Concrete Masonry Units for Construction of Catch Basins and Manholes
Effective Date
15-Dec-2023
Referred By
ASTM E514/E514M-20 - Standard Test Method for Water Penetration and Leakage Through Masonry
Effective Date
15-Dec-2023
Referred By
ASTM C129-23 - Standard Specification for Nonloadbearing Concrete Masonry Units
Effective Date
15-Dec-2023
Referred By
ASTM C1587/C1587M-21a - Standard Practice for Preparation of Field Removed Manufactured Masonry Units and Masonry Specimens for Testing
Effective Date
15-Dec-2023

Buy Standard

ASTM C1232-23 - Standard Terminology for MasonryASTM C1232-23 - Standard Terminology for Masonry
PreviousNext
Standard
ASTM C1232-23 - Standard Terminology for Masonry
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM C1232-23 - Standard Terminology for MasonryREDLINE ASTM C1232-23 - Standard Terminology for Masonry
PreviousNext
Standard
REDLINE ASTM C1232-23 - Standard Terminology for Masonry
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: C1232 − 23
Standard Terminology for
1
Masonry
This standard is issued under the fixed designation C1232; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
1.1 This standard incorporates generic terms and generic 2.1 ASTM Standards:
definitions of terms specifically associated with manufactured C32 Specification for Sewer and Manhole Brick (Made
masonry units and masonry constructed with manufactured From Clay or Shale)
masonry units. These generic terms and definitions are used C34 Specification for Structural Clay Loadbearing Wall Tile
within the standards developed by Committee C12 on Mortars C55 Specification for Concrete Building Brick
and Grouts for Unit Masonry and Committee C15 on Manu- C56 Specification for Structural Clay Nonloadbearing Tile
factured Masonry Units. C62 Specification for Building Brick (Solid Masonry Units
Made from Clay or Shale)
1.2 This standard incorporates terms and definitions of
C67/C67M Test Methods for Sampling and Testing Brick
terms associated with the standards specific to clay masonry
and Structural Clay Tile
units, in particular to Specifications C32, C34, C56, C62,
C73 Specification for Calcium Silicate Brick (Sand-Lime
C126, C212, C216, C279, C410, C530, C652, C902, C1088,
Brick)
C1167, C1261, C1272, and C1405, and to Test Methods
C90 Specification for Loadbearing Concrete Masonry Units
C67/C67M.
C126 Specification for Ceramic Glazed Structural Clay Fac-
1.3 This standard incorporates terms and definitions of
ing Tile, Facing Brick, and Solid Masonry Units
terms associated with the standards specific to concrete ma-
C129 Specification for Nonloadbearing Concrete Masonry
sonry units in particular to Specifications C55, C73, C90,
Units
C129, C139, C744, C1319, C1372, C1491, C1623, and C1634
C139 Specification for Concrete Masonry Units for Con-
and to Test Methods C140/C140M, C426, and C1262/
struction of Catch Basins and Manholes
C1262M.
C140/C140M Test Methods for Sampling and Testing Con-
crete Masonry Units and Related Units
1.4 This standard incorporates terms and definition of terms
C212 Specification for Structural Clay Facing Tile
associated with the standards specific to autoclaved aerated
concrete masonry units in particular to Practice C1692 and to C216 Specification for Facing Brick (Solid Masonry Units
Made from Clay or Shale)
Specifications C1386, C1691, and C1693.
C279 Specification for Chemical-Resistant Masonry Units
1.5 This standard incorporates terms and definitions of
C410 Specification for Industrial Floor Brick
terms associated with the standards specific to clay and
C426 Test Method for Linear Drying Shrinkage of Concrete
concrete roofing tile units in particular to Specifications C1167
Masonry Units
and C1492 and to Test Methods C1568, C1569, and C1570.
C530 Specification for Structural Clay Nonloadbearing
1.6 For terminology specific to mortar and grout, see
Screen Tile
Terminology C1180.
C652 Specification for Hollow Brick (Hollow Masonry
1.7 This international standard was developed in accor- Units Made From Clay or Shale)
dance with internationally recognized principles on standard- C744 Specification for Prefaced Concrete and Calcium Sili-
ization established in the Decision on Principles for the cate Masonry Units
Development of International Standards, Guides and Recom- C902 Specification for Pedestrian and Light Traffic Paving
mendations issued by the World Trade Organization Technical Brick
Barriers to Trade (TBT) Committee. C936/C936M Specification for Solid Concrete Interlocking
Paving Units
1
This terminology is under the jurisdiction of ASTM Committee C15 on
Manufactured Masonry Units and is the direct responsibility of Subcommittee
2
C15.08 on Terminology. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Dec. 15, 2023. Published December 2023. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1993. Last previous edition approved in 2021 as C1232 – 21a. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/C1232-23. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C1232 − 23
C1088 Specification for Thin Veneer Brick Unit
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1232 − 21a C1232 − 23
Standard Terminology for
1
Masonry
This standard is issued under the fixed designation C1232; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This standard incorporates generic terms and generic definitions of terms specifically associated with manufactured masonry
units and masonry constructed with manufactured masonry units. These generic terms and definitions are used within the standards
developed by Committee C12 on Mortars and Grouts for Unit Masonry and Committee C15 on Manufactured Masonry Units.
1.2 This standard incorporates terms and definitions of terms associated with the standards specific to clay masonry units, in
particular to Specifications C32, C34, C56, C62, C126, C212, C216, C279, C410, C530, C652, C902, C1088, C1167, C1261,
C1272, and C1405, and to Test Methods C67/C67M.
1.3 This standard incorporates terms and definitions of terms associated with the standards specific to concrete masonry units in
particular to Specifications C55, C73, C90, C129, C139, C744, C1319, C1372, C1491, C1623, and C1634 and to Test Methods
C140/C140M, C426, and C1262/C1262M.
1.4 This standard incorporates terms and definition of terms associated with the standards specific to autoclaved aerated concrete
masonry units in particular to Practice C1692 and to Specifications C1386, C1691, and C1693.
1.5 This standard incorporates terms and definitions of terms associated with the standards specific to clay and concrete roofing
tile units in particular to Specifications C1167 and C1492 and to Test Methods C1568, C1569, and C1570.
1.6 For terminology specific to mortar and grout, see Terminology C1180.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
C32 Specification for Sewer and Manhole Brick (Made From Clay or Shale)
C34 Specification for Structural Clay Loadbearing Wall Tile
C55 Specification for Concrete Building Brick
C56 Specification for Structural Clay Nonloadbearing Tile
1
This terminology is under the jurisdiction of ASTM Committee C15 on Manufactured Masonry Units and is the direct responsibility of Subcommittee C15.08 on
Terminology.
Current edition approved Dec. 1, 2021Dec. 15, 2023. Published December 2021December 2023. Originally approved in 1993. Last previous edition approved in 2021 as
C1232 – 21.C1232 – 21a. DOI: 10.1520/C1232-21A.10.1520/C1232-23.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C1232 − 23
C62 Specification for Building Brick (Solid Masonry Units Made from Clay or Shale)
C67/C67M Test Methods for Sampling and Testing Brick and Structural Clay Tile
C73 Specification for Calcium Silicate Brick (Sand-Lime Brick)
C90 Specification for Loadbearing Concrete Masonry Units
C126 Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units
C129 Specification for Nonloadbearing Concrete Masonry Units
C139 Specification for Concrete Masonry Units for Construction of Catch Basins and Manholes
C140/C140M Test Methods for Sampling and Testing Concrete Masonry Units and Related Units
C212 Specification for Structural Clay Facing Tile
C216 Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)
C279 Specification for Chemical-Resistant Masonry Units
C410 Specification for Industrial Floor Brick
C426 Test Method for Linear Drying Shrinkage of Concrete Masonry Units
C530 Specification for Structural Clay Nonloadbearing Screen Tile
C652 Specification for Hollow Brick (Hollow Masonry Units Made From Clay or Shale)
C744 Specification for Prefaced Concrete and Calcium Silicate Masonry Units
C902 Spec
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D6866-24(Test Method)
Standard Test Methods for Determining the Biobased Content of Solid, Liquid, and Gaseous Samples Using Radiocarbon Analysis

SIGNIFICANCE AND USE
4.1 This testing method provides accurate biobased/biogenic carbon content results to materials whose carbon source was directly in equilibrium with CO2 in the atmosphere at the time of cessation of respiration or metabolism, such as the harvesting of a crop or grass living its natural life in a field. Special considerations are needed to apply the testing method to materials originating from within artificial environments. Application of these testing methods to materials derived from CO2 uptake within artificial environments is beyond the present scope of this standard.  
4.2 Method B utilizes AMS along with Isotope Ratio Mass Spectrometry (IRMS) techniques to quantify the biobased content of a given product. Instrumental error can be within 0.1-0.5 % (1 relative standard deviation (RSD)), but controlled studies identify an inter-laboratory total uncertainty up to ±3 % (absolute). This error is exclusive of indeterminate sources of error in the origin of the biobased content (see Section 22 on precision and bias).  
4.3 Method C uses LSC techniques to quantify the biobased content of a product using sample carbon that has been converted to benzene. This test method determines the biobased content of a sample with a maximum total error of ±3 % (absolute), as does Method B.  
4.4 The test methods described here directly discriminate between product carbon resulting from contemporary carbon input and that derived from fossil-based input. A measurement of a product’s 14C/12C or 14C/13C content is determined relative to a carbon based modern reference material accepted by the radiocarbon dating community such as NIST Standard Reference Material (SRM) 4990C, (referred to as OXII or HOxII). It is compositionally related directly to the original oxalic acid radiocarbon standard SRM 4990B (referred to as OXI or HOxI), and is denoted in terms of fM, that is, the sample’s fraction of modern carbon. (See Terminology, Section 3.)  
4.5 Reference standards, available to all...
SCOPE
1.1 This standard is a test method that teaches how to experimentally measure biobased carbon content of solids, liquids, and gaseous samples using radiocarbon analysis. These test methods do not address environmental impact, product performance and functionality, determination of geographical origin, or assignment of required amounts of biobased carbon necessary for compliance with federal laws.  
1.2 These test methods are applicable to any product containing carbon-based components that can be combusted in the presence of oxygen to produce carbon dioxide (CO2) gas. The overall analytical method is also applicable to gaseous samples, including flue gases from electrical utility boilers and waste incinerators.  
1.3 These test methods make no attempt to teach the basic principles of the instrumentation used although minimum requirements for instrument selection are referenced in the References section. However, the preparation of samples for the above test methods is described. No details of instrument operation are included here. These are best obtained from the manufacturer of the specific instrument in use.  
1.4 Limitation—This standard is applicable to laboratories working without exposure to artificial carbon-14 (14C). Artificial 14C is routinely used in biomedical studies by both liquid scintillation counter (LSC) and accelerator mass spectrometry (AMS) laboratories and can exist within the laboratory at levels 1,000 times or more than 100 % biobased materials and 100,000 times more than 1% biobased materials. Once in the laboratory, artificial 14C can become undetectably ubiquitous on door knobs, pens, desk tops, and other surfaces but which may randomly contaminate an unknown sample producing inaccurately high biobased results. Despite vigorous attempts to clean up contaminating artificial 14C from a laboratory, isolation has proven to be the only successful method of avoidance. Completely separate chemical ...

  • Standard
    19 pages
    English language
    sale 15% off
  • Standard
    19 pages
    English language
    sale 15% off
ASTM
ASTM F2231-02(2024)(Test Method)
Standard Test Method for Charpy Impact Test on Thin Specimens of Polyethylene Used in Pressurized Pipes

SIGNIFICANCE AND USE
5.1 Brown and Lu4,5 show the Charpy impact energy is related to the ultimate critical temperature of the rapid crack propagation [RCP] behavior as measured by the ISO 13477, S-4 test.6  
5.2 The test method may be used to determine the impact energy of polyethylene used in the manufacture of pipe . This test method involves the preparation of a small compression molded specimen of PE resin that is then notched in a specified manner. The specimen is then broken in a pendulum impact machine. The impact energy is recorded in joules. The value obtained is referred to as the Charpy impact energy.
SCOPE
1.1 This test method describes the specimen preparation and the method of measuring the impact energy of polyethylene used in pressurized pipes.  
1.2 The test specimens are taken from compression molded plaques of the resin from pellets or pipe.  
1.3 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM E3426/E3426M-24(Test Method)
Standard Test Method for Evaluating Aerial Response Robot Endurance

SIGNIFICANCE AND USE
5.1 This test method is part of an overall suite of related test methods that provide repeatable measures of robotic system mobility and remote pilot proficiency. The operational endurance of a robot significantly impacts the performance of the robot during a variety of tasks. Robot endurance is a complex function of robot design, control scheme design, and energy storage selection. This test method evaluates the endurance of a robot through continuous operation. The outdoor and indoor movement tests flight path chosen for endurance testing specifically challenges robotic system locomotion, flight system to maintain position, and remote situational awareness by the remote pilot. As such, it can be used to represent modest outdoor flight or indoor flight within confined areas. The indoor hovering and dwelling tests similarly challenge these capabilities, but for remaining stationary in air within an outdoor or confined indoor area. The endurance test standard provides a method in which the operational endurance of a large variety of robot sizes and locomotion system designs may be compared. The test provides both a measure of the endurance of the robot and a measure of the reliability of the robot when operating continuously for extended periods of time on complex flight paths or continuous use, or both.  
5.2 The indoor tests with containment walls represent repeatable complexity within commercial spaces and residential dwellings with hallways and doorways, or warehouses.  
5.3 The test apparatuses are low-cost and easy to fabricate so they can be widely replicated. The procedure is also simple to conduct. This eases comparisons across various testing locations and dates to determine best-in-class systems and remote pilots.  
5.4 Evaluation—This test method can be used in a controlled environment to measure baseline capabilities. The endurance test apparatus can also be embedded into operational training scenarios to measure degradation due to uncontrolled variab...
SCOPE
1.1 This test method is intended for remotely operated aerial response robots (that is, unmanned aerial systems [UAS], drones, unmanned aircrafts) operating in complex, unstructured, and often hazardous environments. It specifies the apparatuses, procedures, and performance metrics necessary to measure the mission endurance of an aerial robot while either station keeping or following an approximate flight path defined by obstacles or boundaries, or both, intended to induce repeated cyclical movement. This test method is one of several robot tests that can be used to evaluate overall system capabilities.  
1.2 The robotic system includes a remote pilot in control of most functionality, so an onboard camera and remote pilot display are typically required. This test method can be used to evaluate assistive or autonomous behaviors intended to improve the effectiveness or efficiency of remotely operated systems.  
1.3 Different user communities can set their own thresholds of acceptable performance within this test method for various mission requirements.  
1.4 Performing Location—This test method may be performed anywhere the specified apparatuses and environmental conditions can be implemented. Flying unmanned aircraft without a comprehensive understanding of the laws and regulations enforced by the relevant jurisdiction poses significant safety and legal risks. Failure to comply with these regulations may result in accidents, injuries, property damage, and legal consequences. Users of this standard are strongly advised to review and adhere to all applicable ASTM Committee F38 standards and to ensure full compliance with the authorities holding jurisdiction.  
1.5 Units—The International System of Units (SI Units) and U.S. Customary Units (Imperial Units) are used throughout this document. They are not mathematical conversions. Rather, they are approximate equivalents in each system of units to enable use of readily ava...

  • Standard
    14 pages
    English language
    sale 15% off
ASTM
ASTM F714-24(Specification)
Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter

ABSTRACT
This specification covers polyethylene (PE) pipe made in dimensions based on outside determined range of diameters and larger. The piping is intended for new construction and insertion renewal of old piping systems used for the transport of water, municipal sewage, domestic sewage, industrial process liquids, effluents, slurries, etc., in both pressure and nonpressure systems. Different dimensional properties of pipes like outside diameter, wall thickness, eccentricity, toe-in, and special sizes shall be determined. Physical properties such asdensity, melt index, flexural modulus, tensile strength, slow crack growth resistance, hydrostatic strength, color and UV stabilizer, HDB, and HDS shall determined as well. In order to determine the performance of pipes under pressure the following tests shall be done: short-term pressurization test and elevated temperature sustained pressure test. The pipe shall be homogeneous throughout and essentially uniform in color, opacity, density, and other properties. The inside and outside surfaces shall be semi matte or glossy in appearance (depending on the type of plastic) and free of chalking, sticky, or tacky material. The surfaces shall be free of excessive bloom, that is, slight bloom is acceptable. The pipe walls shall be free of cracks, holes, blisters, voids, foreign inclusion, or other defects that are visible to the naked eye and that may affect the wall integrity. Holes deliberately placed in perforated pipe are acceptable. Bloom or chalking may develop in pipe exposed to direct rays of the sun (ultraviolet radiant energy) for extended periods and, consequently, these requirements do not apply to pipe after extended exposure to direct rays of the sun.
SCOPE
1.1 This specification covers polyethylene (PE) pipe made in three standard outside diameter sizing systems, based on outside diameters of DIPS 3, IPS 4, Metric 90 mm and larger. For smaller sizes refer to Specification D3035. See 5.2.5 for guidelines on special sizes.  
1.2 The piping is intended for new construction and insertion renewal of old piping systems used for the transport of water, municipal sewage, domestic sewage, industrial process liquids, effluents, slurries, etc., in both pressure and nonpressure systems.
Note 1: The user should consult the manufacturer to ensure that any mechanical or chemical effects to the polyethylene pipe caused by the material being transported will not affect the service life beyond limits acceptable to the user. See PPI TR-19 Chemical Resistance of Thermoplastic Piping Materials for guidance on chemical effects, www.plasticpipe.org  
1.3 All pipes produced under this specification are pressure-rated. See Appendix X5 for information on pressure rating.
Note 2: References and material descriptions for PE2406, PE3408 and materials having a HDB of 1450 psi have been removed from Specification F714 due to changes in Specification D3350 and PPI TR-3. For removed designations, refer to previous editions of Specification F714, Specification D3350, PPI TR-3 and PPI TR-4. The removal of these materials does not affect pipelines that are in service. See Note 4 and Note 9.  
1.4 This specification includes criteria for choice of raw material, together with performance requirements and test methods for determining conformance with the requirements.  
1.5 Quality-control measures are to be taken by manufacturers. See Appendix X4 for general information on quality control.  
1.6 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.7 The following safety hazards caveat pertains only to the test methods portion, Section 6, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard t...

  • Technical specification
    12 pages
    English language
    sale 15% off
  • Technical specification
    12 pages
    English language
    sale 15% off
ASTM
ASTM F2136-18(2024)(Test Method)
Standard Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE Resins or HDPE Corrugated Pipe

SIGNIFICANCE AND USE
4.1 This test method does not purport to interpret the data generated.  
4.2 This test method is intended to compare slow-crack-growth (SCG) resistance for a limited set of HDPE resins.  
4.3 This test method may be used on virgin HDPE resin compression-molded into a plaque or on extruded HDPE corrugated pipe that is chopped and compression-molded into a plaque (see 7.1.1 for details).
SCOPE
1.1 This test method is used to determine the susceptibility of high-density polyethylene (HDPE) resins or corrugated pipe to slow-crack-growth under a constant ligament-stress in an accelerating environment. This test method is intended to apply only to HDPE of a limited melt index (0.947 g/cm3 to 0.955 g/cm3). This test method may be applicable for other materials, but data are not available for other materials at this time.  
1.2 This test method measures the failure time associated with a given test specimen at a constant, specified, ligament-stress level.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 Definitions are in accordance with Terminology F412, and abbreviations are in accordance with Terminology D1600, unless otherwise specified.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM C1503-24(Specification)
Standard Specification for Silvered Flat Glass Mirror

ABSTRACT
This specification covers the requirements for silvered flat glass mirrors of rectangular shape supplied as cut sizes, stock sheets or as lehr ends and to which no further processing (such as edgework or other fabrication) has been done. The quality requirements of silvered annealed monolithic clear and tinted flat glass mirrors up to a certain thickness are also discussed. The mirrors are intended to be used indoors for mirror glazing, for components of decorative accessories or for similar uses. The mirrors are not intended for use in environments where high humidity or airborne corrosion promoters, or both, are consistently present (such as swimming pool areas, ocean-going vessels, chemical laboratories and other corrosive environments). The classification of mirrors are according to the following properties: grades, cut size, stock sheet, lehr end, select quality, glazing quality, color (clear or tinted), and thickness. Different test methods shall be performed in order to determine or measure the following properties: reflectance, silver coating appearance, coating resistance, blemish (point and linear blemishes), dimension, and squareness.
SCOPE
1.1 This specification covers the requirements for silvered flat glass mirrors of rectangular shape supplied as cut sizes, stock sheets, or as lehr ends and to which no further processing (such as edgework or other fabrication) has been done.  
1.2 This specification covers the quality requirements of silvered annealed monolithic clear and tinted flat glass mirrors only, up to 6 mm (1/4 in.) thick. The mirrors are intended to be used indoors for mirror glazing, for components of decorative accessories or for similar uses.  
1.3 This specification does not address safety glazing materials nor requirements for mirror applications. Consult model building codes and other applicable standards for safety glazing applications.  
1.4 Mirrors covered in this specification are not intended for use in environments where high humidity or airborne corrosion promoters, or both, are consistently present (such as swimming pool areas, ocean-going vessels, chemical laboratories, and other corrosive environments).  
1.5 The dimensional values stated in metric units are to be regarded as the standard. The inch-pound units given in parentheses are for information only.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM E1044-96(2024)(Specification)
Standard Specification for Glass Serological Pipets (General Purpose and Kahn)

ABSTRACT
This specification covers reusable glass serological pipets used for measuring volumes of liquid. The pipets may be classified into three styles according to operational set-up and should be made with approved glass materials. Each pipet should be straight, of one-piece construction, and properly calibrated. All products should conform to the required dimension of delivery tips, zero gradation line position, dimensions and outflow times, graduation markings, color coding, identification markings, and workmanship.
SCOPE
1.1 This specification covers glass serological pipets, used in measuring volumes of liquids.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2921-98(2024)(Test Method)
Standard Test Method for Qualitative Tests for the Presence of Water Repellents and Preservatives in Wood Products

SIGNIFICANCE AND USE
3.1 Although chlorinated phenol-treated wood has become less common due to environmental concerns, repellent-treated wood is commonly specified in construction. This test method provides a means to verify the presence of a significant level of water repellent protection.
SCOPE
1.1 This test method covers simple qualitative field or laboratory tests to determine water repellency or the presence of chlorinated phenol2 preservative chemicals in wood products that are specified to be water repellent preservative treated.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D1240-24(Test Method)
Standard Test Methods for Rosin Acids Content of Pine Chemicals, Including Rosin, Tall Oil, and Related Products

SIGNIFICANCE AND USE
4.1 This is a revision of the method for measuring rosin acids content combines the three major ways of determining the rosin acids content of pine chemicals products into a single method.  
4.1.1 For materials containing less than 15 % rosin, the modified Glidden procedure has gained acceptance. For materials containing more than 15 % rosin the modified Wolfe Method is preferred. The modified Wolfe and modified Glidden procedures differ only in their details. They have been combined here into a single procedure. This procedure can be run using either a potentiometer or an internal indicator to determine the end point of the titration. Use of a potentiometer is preferred and is the referee method. Use of an internal indicator is the principal alternative method. They will be referred to as the Potentiometric Method and the Internal Indicator Method.
SCOPE
1.1 These test methods cover the determination of rosin acids in tall oil, tall oil fatty acid, tall oil rosin, and other pine chemicals products.  
1.2 These test methods may not be applicable to adducts or derivatives of rosin, fatty acid, or other pine chemicals products.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM E1135-19(2024)(Test Method)
Standard Test Method for Comparing the Brightness of Fluorescent Penetrants

SIGNIFICANCE AND USE
5.1 The principle use of this procedure is for the comparison of the brightness between batches of fluorescent penetrants compared to a specified standard, as a batch quality control test.  
5.2 The procedure is also utilized in monitoring the brightness of an in-use penetrant against the brightness of the unused sample of the same material.  
5.3 The significance of the results are not absolute values but rather relative comparisons at a point in time, by a particular laboratory or operator on the specified fluorometer.
SCOPE
1.1 This test method describes the techniques for comparing the brightness of the penetrants used in the fluorescent dye penetrant process. This comparison is performed under controlled conditions that eliminate most of the variables present in actual penetrant examination. Thus, the brightness factor is isolated and is measured independently of the other factors which affect the performance of a penetrant system.  
1.2 The brightness of a penetrant indication is affected by the developer with which it is used. This test method, however, measures the brightness of a penetrant on a convenient filter paper substrate which serves as a substitute for the developer.  
1.3 The brightness measurement obtained is color-corrected to approximate the color response of the average human eye. Since most examinations are done by human eyes, this number has more practical value than a measurement in units of energy emitted. Also, the comparisons are expressed as a percentage of some chosen standard penetrant because no absolute system of measurement exists at this time.  
1.4 The measurements made by this standard compare the brightness of a candidate penetrant to that of a standard penetrant when tested according to the technique. There is no known correlation between the results obtained and the brightness of actual flaw indications obtained using the penetrant in inspection.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off