ASTM D843-17
(Specification)Standard Specification for Nitration Grade Xylene
Standard Specification for Nitration Grade Xylene
ABSTRACT
This specification covers nitration grade xylene. The nonaromatic hydrocarbons, acid wash color, copper corrosion, appearance, distillation range, initial distillation temperature, and dry point of nitration grade xylene shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers nitration grade xylene.
1.2 The following applies to all specified limits in this standard: for purposes of determining conformance with this standard, an observed value or a calculated value shall be round off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the round-off method of Practice E29.
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.4 Consult OSHA regulations, supplier’s Safety Data Sheets, and local regulations for all materials used in this specification.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D843 −17
Standard Specification for
1
Nitration Grade Xylene
This standard is issued under the fixed designation D843; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D5386 Test Method for Color of Liquids Using Tristimulus
Colorimetry
1.1 This specification covers nitration grade xylene.
D6563 Test Method for Benzene, Toluene, Xylene (BTX)
1.2 The following applies to all specified limits in this
Concentrates Analysis by Gas Chromatography
standard: for purposes of determining conformance with this
D8005 Test Method for Color of Clear Liquids (Platinum-
standard, an observed value or a calculated value shall be
Cobalt Scale)
round off “to the nearest unit” in the last right-hand digit used
E29 Practice for Using Significant Digits in Test Data to
in expressing the specification limit, in accordance with the
Determine Conformance with Specifications
round-off method of Practice E29.
E2680 Test Method for Appearance of Clear, Transparent
1.3 The values stated in SI units are to be regarded as
Liquids (Visual Inspection Procedure)
standard. The values given in parentheses are for information
2.2 Other Document:
only.
OSHA Regulations, 29 CFR paragraphs 1910.1000 and
1.4 Consult OSHA regulations, supplier’s Safety Data
3
1910.1200
Sheets, and local regulations for all materials used in this
specification.
3. Properties
1.5 This international standard was developed in accor-
3.1 Nitration grade xylene shall conform to the following
dance with internationally recognized principles on standard-
requirements:
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom- ASTM Test
Property Specification
A
Method
mendations issued by the World Trade Organization Technical
Nonaromatic hydrocarbons, max, volume % 4.0 D6563
Barriers to Trade (TBT) Committee.
Acid wash color, max pass with 6 D848
Copper corrosion pass (1A or 1B) D849
Appearance, free of haze, particulates pass E2680
2. Referenced Documents
or suspended matter particles
2
Color, Pt/Co scale, max 20 D5386 or
2.1 ASTM Standards:
D8005
D848 Test Method for Acid Wash Color of Industrial Aro-
Distillation range at 101.3 kPa (760 mm Hg 5 D850
matic Hydrocarbons pressure), max,°C
Initial distillation temperature, min,°C 137 D850
D849 Test Method for Copper Strip Corrosion by Industrial
Dry point, max,°C 143 D850
Aromatic Hydrocarbons
D850 Test Method for Distillation of Industrial Aromat
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D843 − 16 D843 − 17
Standard Specification for
1
Nitration Grade Xylene
This standard is issued under the fixed designation D843; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*Scope
1.1 This specification covers nitration grade xylene.
1.2 The following applies to all specified limits in this standard: for purposes of determining conformance with this standard,
an observed value or a calculated value shall be round off “to the nearest unit” in the last right-hand digit used in expressing the
specification limit, in accordance with the round-off method of Practice E29.
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.4 Consult OSHA regulations, supplier’s Safety Data Sheets, and local regulations for all materials used in this specification.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D848 Test Method for Acid Wash Color of Industrial Aromatic Hydrocarbons
D849 Test Method for Copper Strip Corrosion by Industrial Aromatic Hydrocarbons
D850 Test Method for Distillation of Industrial Aromatic Hydrocarbons and Related Materials
D3437 Practice for Sampling and Handling Liquid Cyclic Products
D5386 Test Method for Color of Liquids Using Tristimulus Colorimetry
D6563 Test Method for Benzene, Toluene, Xylene (BTX) Concentrates Analysis by Gas Chromatography
D8005 Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E2680 Test Method for Appearance of Clear, Transparent Liquids (Visual Inspection Procedure)
2.2 Other Document:
3
OSHA Regulations, 29 CFR paragraphs 1910.1000 and 1910.1200
1
This specification is under the jurisdiction of ASTM Committee D16 on Aromatic Hydrocarbons Aromatic, Industrial, Specialty and Related Chemicals and is the direct
responsibility of Subcommittee D16.01 on Benzene, Toluene, Xylenes, Cyclohexane and Their Derivatives.
Current edition approved June 1, 2016June 1, 2017. Published June 2016June 2017. Originally approved in 1945. Last previous edition approved in 20112016 as D843 – 06
ɛ1
(2011)D843 – 16. . DOI: 10.1520/D0843-16.10.1520/D0843-17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact AS
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.