iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM C901-01

(Specification)

Standard Specification for Prefabricated Masonry Panels

Standard Specification for Prefabricated Masonry Panels

ABSTRACT
This specification covers the structural design and quality control of fabrication for load-bearing and non-load-bearing prefabricated masonry panels. Structural design of panels shall be performed in accordance with the provisions of the applicable local building code and the requirements specified. A quality control test shall be made in accordance with the specified requirements.
SCOPE
1.1 This specification covers the structural design and quality control of fabrication for load-bearing and non-load-bearing prefabricated masonry panels. Methods of prefabrication, field erection, and jointing are not covered in this specification.

General Information

Status
Historical
Publication Date
09-Aug-2001
ICS
91.060.10 - Walls. Partitions. Facades
Technical Committee
C15 - Manufactured Masonry Units
Drafting Committee
C15.05 - Masonry Assemblies
Current Stage
Ref Project

Relations

Replaces
ASTM C901-93a - Standard Specification for Prefabricated Masonry Panels
Effective Date
10-Aug-2001
Replaced By
ASTM C901-09 - Standard Specification for Prefabricated Masonry Panels
Effective Date
15-Jun-2009

Buy Standard

ASTM C901-01 - Standard Specification for Prefabricated Masonry PanelsASTM C901-01 - Standard Specification for Prefabricated Masonry Panels
PreviousNext
Technical specification
ASTM C901-01 - Standard Specification for Prefabricated Masonry Panels
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C 901 – 01
Standard Specification for
1
Prefabricated Masonry Panels
This standard is issued under the fixed designation C901; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope C67 Test Methods for Sampling and Testing Brick and
7
Structural Clay Tile
1.1 This specification covers the structural design and qual-
C73 Specification for Calcium Silicate Brick (Sand-Lime
itycontroloffabricationforload-bearingandnon-load-bearing
7
Brick)
prefabricated masonry panels. Methods of prefabrication, field
C 90 Specification for Loadbearing Concrete Masonry
erection, and jointing are not covered in this specification.
7
Units
2. Referenced Documents
C109/C109M Test Method for Compressive Strength of
Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube
2.1 ASTM Standards:
8
Specimens)
A82 Specification for Steel Wire, Plain, for Concrete Re-
2
C126 Specification for Ceramic Glazed Structural Clay
inforcement
7
Facing Tile, Facing Brick, and Solid Masonry Units
A116 Specification for Metallic-Coated Steel Woven Wire
3
C140 Test Methods of Sampling and Testing Concrete
Fence Fabric
7
Masonry Units and Related Units
A153 SpecificationforZincCoating(Hot-Dip)onIronand
7
3
C212 Specification for Structural Clay Facing Tile
Steel Hardware
C216 Specification for Facing Brick (Solid Masonry Units
A 167 Specification for Stainless and Heat-Resisting
7
4
Made from Clay or Shale)
Chromium-Nickel Steel Plate, Sheet, and Strip
7
C270 Specification for Mortar for Unit Masonry
A185 Specification for Steel Welded Wire, Fabric, Plain,
7
2
C476 Specification for Grout for Masonry
for Concrete Reinforcement
C652 Specification for Hollow Brick (Hollow Masonry
A 615/A 615M Specification for Deformed and Plain
7
2
Units Made from Clay or Shale)
Billet-Steel Bars for Concrete Reinforcement
C744 Specification for Prefaced Concrete and Calcium
A616/A616M Specification for Rail-Steel Deformed and
7
5
Silicate Masonry Units
Plain Bars for Concrete Reinforcement
C780 Test Method for Preconstruction and Construction
A617/A617M Specification for Axle-Steel Deformed and
5
Evaluation of Mortars for Plain and Reinforced Unit
Plain Bars for Concrete Reinforcement
7
Masonry
B227 Specification for Hard-Drawn Copper-Clad Steel
7
6
C1019 Test Method of Sampling and Testing Grout
Wire
C1314 Test Method of Compressive Strength of Masonry
C34 Specification for Structural Clay Load-Bearing Wall
7
7
Prisms
Tile
7
C 1357 Test Methods for Evaluating Masonry Bond
C55 Specification for Concrete Brick
7
Strength
C62 SpecificationforBuildingBrick(SolidMasonryUnits
7
E72 Methods of Conducting Strength Tests of Panels for
Made from Clay or Shale)
8
Building Construction
E447 Test Methods for Compressive Strength of Labora-
1
9
This specification is under the jurisdiction of ASTM Committee C15 on
tory Constructed Masonry Prisms
Manufactured Masonry Units and is the direct responsibility of Subcommittee
E518 Test Methods for Flexural Bond Strength of
C15.05 on Masonry Assemblies.
7
Masonry
Current edition approved Aug. 10, 2001. Published October 2001. Originally
published as C901 – 79. Last previous edition C901 – 93a.
2
Annual Book of ASTM Standards, Vol 01.04.
3
Annual Book of ASTM Standards, Vol 01.06.
4
Annual Book of ASTM Standards, Vol 01.03.
5
Discontinued. See 1998 Annual Book of ASTM Standards, Vol 01.04.
6 8
Annual Book of ASTM Standards, Vol 02.03. Annual Book of ASTM Standards, Vol 04.01.
7 9
Annual Book of ASTM Standards, Vol 04.05. Discontinued. See 1999 Annual Book of ASTM Standards, Vol 04.05.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
C901–01
3. Materials and Manufacture 3.4.4 Specification A616 for rail-steel deformed and plain
bars for concrete reinforcement.
3.1 Masonry Units—Masonry units shall conform to the
3.4.5 Specification A617/A617M for axle-steel deformed
following applicable specifications:
and plain bars for concrete reinforcement.
3.1.1 Brick—Specification C62 for building brick, Specifi-
cation C216 for facing brick, Specification C126 for ceramic
4. Structural Design
glazed structural clay tile, facing brick, and solid masonry
4.1 General—Structural design of panels shall be per-
units, and Specification C652 for hollow brick.
formed in accordance with the provisions of the applicable
3.1.2 Concrete Masonry Units—Specification C55 for con-
local building code and the requirements of this specification.
crete building brick, Specificati
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E519/E519M-22(Test Method)
Standard Test Method for Diagonal Tension (Shear) in Masonry Assemblages

SIGNIFICANCE AND USE
3.1 This test method was developed to measure more accurately the diagonal tensile (shear) strength of masonry than was possible with other available methods. The specimen size was selected as being the smallest that would be reasonably representative of a full-size masonry assemblage and that would permit the use of testing machines such as are used by many laboratories.
Note 1: As a research test method used only for the purpose of evaluating the effects of variables such as type of masonry unit, mortar, workmanship, etc., a smaller size specimen could be used if the available testing equipment will not accommodate a 1.2-m [4-ft] square specimen. However, there is a lack of experimental data that would permit an evaluation of the effect of specimen size on the shear strength or to permit a correlation between the results of small-scale specimen tests and larger specimens.
SCOPE
1.1 This test method covers determination of the diagonal tensile or shear strength of masonry assemblages by loading them in compression along one diagonal (see Fig. 1), thus causing a diagonal tension failure with the specimen splitting apart parallel to the direction of load.
FIG. 1 Apparatus for Determination of Diagonal Tensile or Shear Strength Masonry Assemblages  
1.2 Annex A1 provides requirements regarding the determination of the diagonal-tension strength of masonry under combined diagonal-tension and compressive loading.  
1.3 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 These test methods cover the application of the tests using either inch-pound or SI units. The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.5 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM C1072-22(Test Method)
Standard Test Methods for Measurement of Masonry Flexural Bond Strength

SIGNIFICANCE AND USE
5.1 This test method is intended for use in comparing the bond strengths (under the given conditions) of masonry mortars.  
5.2 This test method could be used, for example, to check one aspect of the quality of mortar products after production, or to indicate the bond potential of a mortar product without requiring the product to be tested in combination with many different units.  
5.3 This test method uses controlled conditions of fabrication and curing that are not intended to represent field conditions.  
5.4 This test method uses standard concrete masonry units. Mortars are batched by weight equivalents of volume proportions and are mixed to a prescribed flow. Prisms are constructed using a jig and are bag-cured.  
5.5 Flexural bond strength determined by this test method shall not be interpreted as the flexural bond strength of a wall (because standard units are not used for wall construction), nor shall it be interpreted as an indication of extent of bond for purposes of water permeability evaluation.
SCOPE
1.1 These test methods evaluate the flexural bond strength, normal to the bed joints, of masonry built of manufactured masonry units. Sampling and testing procedures are referenced, and terms are defined. Three different specimen fabrication methods are specified, each for a different purpose:  
1.1.1 The first method is the “Test Method for Laboratory-Prepared Specimens.” Its purpose is to compare the bond strengths (under the given conditions) of masonry mortars. It could be used, for example, to check the quality of mortar products after production, or to indicate the bond strength (under the given conditions) of a mortar product without requiring the product to be tested in combination with many different units. It is not intended to represent field conditions. It uses standard concrete masonry units. Mortars are batched by weight equivalents of volume proportions and are mixed to a prescribed flow. Prisms are constructed using a jig and are bag-cured.  
1.1.2 The second method is the “Test Method for Field-Prepared Specimens.” Its purpose is to evaluate the bond strength (under the given conditions) of a particular unit-mortar combination, either for preconstruction evaluation of materials or for quality control purposes during construction. Mortars are batched conventionally, and the flow is not prescribed. Prisms are constructed conventionally (no jig) and are bag-cured.  
1.1.3 The third method is the “Test Method for Prisms Removed from Existing Masonry.” Its purpose is to evaluate the bond strength of unit-mortar combinations of prisms cut from existing walls.  
1.1.4 The three methods are not consistent, nor are they intended to be. They are intended to be used for three different purposes. To make this clear, the three methods are presented separately.  
1.1.5 Appendix X1 suggests two possible criteria for assessing the bond strength values obtained using these test methods. These possible evaluation criteria are given for illustration only and are not mandatory.  
1.2 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Princip...

  • Standard
    19 pages
    English language
    sale 15% off
  • Standard
    19 pages
    English language
    sale 15% off
ASTM
ASTM C1197-22(Test Method)
Standard Test Method for In Situ Measurement of Masonry Deformability Properties Using the Flatjack Method

SIGNIFICANCE AND USE
5.1 Deformation and strength properties are measured only on the masonry between flatjacks. Boundary effects of the collar joint behind the wythe tested and adjacent masonry are neglected. In the case of multi-wythe masonry, deformability is estimated only in the wythe in which the flatjack is inserted. Deformability of other wythes may be different.
SCOPE
1.1 This test method describes an in situ method for determining the deformation properties of existing unreinforced solid-unit masonry. (See Note 1.) This test method concerns the measurement of in-situ masonry deformability properties in existing masonry by use of thin, bladder-like flatjack devices that are installed in cut mortar joints in the masonry wall. This test method provides a relatively non-destructive means of determining masonry properties.
Note 1: Solid-unit masonry is that built with stone, concrete, or clay units whose net area is equal to or greater than 75 % of the gross area.  
1.2 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM E518/E518M-22(Test Method)
Standard Test Methods for Flexural Bond Strength of Masonry

SIGNIFICANCE AND USE
4.1 These test methods are intended to provide simplified and economical means for gathering comparative research data on the flexural bond strength developed with different types of masonry units and mortar or for the purpose of checking job quality control (materials and workmanship).
Note 2: These test methods are not intended for use in establishing design stresses. For this purpose, Test Methods C1717 should be used.
SCOPE
1.1 These test methods cover determination of the flexural bond strength of unreinforced masonry assemblages. Two procedures are provided:  
1.1.1 Test Method A—Simply supported beam with third-point loading.  
1.1.2 Test Method B—Simply supported beam with uniform loading.
Note 1: Third-point loading (Test Method A) produces a moment distribution that is significantly different from uniformly distributed loading (Test Method B).Third-point loading (Test Method A) subjects more mortar joints to the maximum moment and thus, is likely to produce more conservative capacities than uniform loading (Test Method B).  
1.2 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.3 These test methods cover the application of the tests using either inch-pound or SI units. The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM C1196-20(Test Method)
Standard Test Method for In Situ Compressive Stress Within Solid Unit Masonry Estimated Using Flatjack Measurements

SIGNIFICANCE AND USE
5.1 Stress is applied as pressure over the area of the flatjack. In the case of multi-wythe masonry, stress is estimated only in the wythe in which the flatjack is inserted. Stress in other wythes may be different.
SCOPE
1.1 This test method covers the determination of the average compressive stress in existing unreinforced solid-unit masonry (see Note 1). This test method concerns the measurement of in-situ compressive stress in existing masonry by use of thin, bladder-like flatjack devices that are installed in cut mortar joints in the masonry wall. This test method provides a relatively non-destructive means of determining masonry properties in place.
Note 1: Solid-unit masonry is that built with stone, concrete, or clay units whose net area is equal to or greater than 75 % of the gross area.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM C1717-19(Test Method)
Standard Test Methods for Conducting Strength Tests of Masonry Wall Panels

SIGNIFICANCE AND USE
4.1 The test methods described in this standard are intended for use as a starting point in developing specific testing protocols for masonry elements.  
4.1.1 The testing protocols could be used for general research on the load-deflection behavior of masonry elements.  
4.1.2 The testing protocols could be used for qualification of masonry elements and materials by evaluation services and other parties.  
4.1.3 The test methods described in this standard are general, and are intended to be adaptable to address a wide range of anticipated support and loading conditions.  
4.2 How the test results are interpreted will depend on the intended use of the masonry element being tested.
SCOPE
1.1 These test methods cover methods for determining the strength and load-deflection characteristics of masonry wall elements.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM C901-18(Specification)
Standard Specification for Prefabricated Masonry Panels

ABSTRACT
This specification covers the structural design and quality control of fabrication for load-bearing and non-load-bearing prefabricated masonry panels. Structural design of panels shall be performed in accordance with the provisions of the applicable local building code and the requirements specified. A quality control test shall be made in accordance with the specified requirements.
SCOPE
1.1 This specification covers the structural design and quality control of fabrication for load-bearing and non-load-bearing prefabricated masonry panels. Methods of prefabrication, field erection, and jointing are not covered in this specification.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM C1280-18(2023)(Specification)
Standard Specification for Application of Exterior Gypsum Panel Products for Use as Sheathing

ABSTRACT
This specification covers the minimum requirements for and the methods of application of gypsum sheathing for use as a substrate for exterior wall cladding. Gypsum sheathing board is a substrate that shall be covered by an exterior cladding or other weather-resistive barrier and is not intended for long-term exposure. Framing members shall be installed so that the surface will be in an even plane, unless otherwise specified, after the gypsum sheathing has been applied. The gypsum sheathing shall be cut by scoring and breaking or by sawing, working from the face side. The cut edges and ends of gypsum sheathing shall be trimmed to obtain neat fitting joints when installed. Gypsum sheathing shall be fitted snugly around all window and door openings. Control joints, other accessories, and metal plaster base shall be fastened through gypsum sheathing to framing members. Where fire resistance or shear resistance is not required, and when metal lath and Portland cement plaster are to be applied as the exterior cladding over gypsum sheathing installed over framing members and the metal lath shall be installed after the gypsum sheathing, the gypsum sheathing shall be permitted to be applied and fastening of the gypsum sheathing shall be completed with the attachment of the self-furred metal lath.
SCOPE
1.1 This specification covers the minimum requirements for and methods of application of exterior gypsum panel products that are specifically designed for use as a substrate for exterior cladding.  
1.1.1 This specification does not cover gypsum panel products that are specifically designed for interior applications.  
1.2 Details of construction for a specific assembly to achieve the required fire resistance shall be obtained from reports of fire-resistance tests, engineering evaluations, or listings from recognized fire testing laboratories.  
1.2.1 This specification shall govern where it is more stringent (size or thickness of framing and size and spacing of fasteners) than the fire-rated construction.  
1.3 Where sound control is required for a gypsum panel product assembly, the details of construction shall be in accordance with the acoustical test report of an assembly that has met the required acoustical value(s).  
1.3.1 This specification shall govern where it is more stringent (size or thickness of framing and size and spacing of fasteners) than the sound-rated construction.  
1.4 Where resistance to racking loads or shear is required for a gypsum panel product assembly, the details of construction shall be in accordance with the racking or shear test report of an assembly that has met the required racking or shear value(s).  
1.4.1 This specification shall govern where it is more stringent (size or thickness of framing and size and spacing of fasteners) than the racking or shear-tested construction.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 The text of this standard references notes which provide explanatory material. These notes shall not be considered as requirements of the standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM F3660-23(Specification)
Standard Consumer Safety Performance Specification for Motorized Partitions

SCOPE
1.1 This consumer safety performance specification establishes performance requirements, test methods, and labeling requirements for motorized partitions.  
1.2 Motorized partitions are used to provide flexibility in the size of spaces typically used for meetings, sports, recreational areas, schools, or social functions where children are often present.  
1.3 Motorized partitions include a motor to direct the opening and closing of the partition and are operated by trained individuals who control the on/off mechanism and opening and closing movement of the partition.  
1.4 The partition is made up of a series of rigid panels that move along a track.  
1.5 This specification does not include motorized curtains, elevator or garage doors, or non-motorized partitions.  
1.6 This specification shall be taken into consideration by owners/operators, architects, planners, engineers, equipment manufacturers, construction companies, construction contractors, and appropriate inspectors who may be involved in the design and construction of new facilities.  
1.7 This specification applies to the installation of new motorized partitions but may be useful for renovation projects such as updating older motorized partitions.  
1.8 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM E1996-23(Specification)
Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Windborne Debris in Hurricanes

ABSTRACT
This specification covers exterior windows, glazed curtain walls, doors and impact protective systems used in buildings located in geographic regions that are prone to hurricanes. The test specimens shall be Fenestration assemblies, and impact protective systems; which shall be tested using the large missile test, and small missile test. The air pressure cycling, missiles, and impact location are also detailed.
SCOPE
1.1 This specification covers exterior windows, glazed curtain walls, doors, and impact protective systems used in buildings located in geographic regions that are prone to hurricanes.  
1.1.1 Exception—Exterior garage doors and rolling doors are governed by ANSI/DASMA 115 and are beyond the scope of this specification.  
1.2 This specification provides the information required to conduct Test Method E1886.  
1.3 Qualification under this specification provides a basis for judgment of the ability of applicable elements of the building envelope to remain unbreached during a hurricane; thereby minimizing the damaging effects of hurricanes on the building interior and reducing the magnitude of internal pressurization. While this standard was developed for hurricanes, it may be used for other types of similar windstorms capable of generating windborne debris.  
1.4 This specification provides a uniform set of guidelines based upon currently available information and research.2 As new information and research becomes available it will be considered.  
1.5 All values are stated in SI units and are to be regarded as standard. Values given in parentheses are for information only. Where certain values contained in reference documents cited and quoted herein are stated in inch-pound units, they must be converted by the user.  
1.6 The following precautionary statement pertains only to the test method portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    15 pages
    English language
    sale 15% off
  • Technical specification
    15 pages
    English language
    sale 15% off