CR 14245:2001
(Main)Guidelines for the application of EN 197-2 "Conformity Evaluation"
Guidelines for the application of EN 197-2 "Conformity Evaluation"
EN 197-2 specifies the scheme for the evaluation of conformity of cements to their corresponding product specification standards, including certification of conformity by a certification body.
The standard provides technical rules for factory production control by the manufacturer, including autocontrol testing of samples, and for the tasks of the certification body. It also provides rules for actions to be followed in the event of non-conformity, the procedure for the certification of conformity and requirements for dispatching centres.
In EN 197-2 the word "cement" is used to refer both to common cements as defined in EN 197-1 and to other cements and binders for which the relevant product specification standard makes reference to EN 197-2 and which are submitted for certification. Such a cement is produced at a given factory and belongs to a particular type and a particular strength class, as defined and specified in the relevant product specification standard. ¿
Smernice za uporabo EN 197-2 "Ovrednotenje skladnosti"
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST-TP CR 14245:2004
01-januar-2004
Smernice za uporabo EN 197-2 "Ovrednotenje skladnosti"
Guidelines for the application of EN 197-2 "Conformity Evaluation"
Ta slovenski standard je istoveten z: CR 14245:2001
ICS:
91.100.10 Cement. Mavec. Apno. Malta Cement. Gypsum. Lime.
Mortar
SIST-TP CR 14245:2004 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TP CR 14245:2004
---------------------- Page: 2 ----------------------
SIST-TP CR 14245:2004
CEN REPORT
CR 14245
RAPPORT CEN
CEN BERICHT
July 2001
ICS
English version
Guidelines for the application of EN 197-2 “Conformity
Evaluation”
This CEN Report was approved by CEN on 13 March 2001. It has been drawn up by the Technical Committee CEN/TC 51.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. CR 14245:2001 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST-TP CR 14245:2004
CR 14245:2001 (E)
Introduction to this Guidelines Document
Purpose
The purpose of this Guidelines Document is to provide explanatory detail on points not
fully elaborated in EN 197-2. It is intended for use by manufacturers and by
certification bodies involved in the certification of cement following EN 197-2, in
particular for the issuing of an EC Certificate of Conformity.
This Document does not deal with the necessary internal procedures that the
certification bodies will have.
It is an objective of this Guidelines Document that its use will assist in the
establishment of equivalent procedures for certification of cement. It is expected that,
following this Document, traditional good procedures and practices that may be
different can continue to be used, provided that they are not in contradiction with EN
197-2 and the relevant product specification standard. Such existing good procedures
and practices, applied in conjunction with these Guidelines, are not considered to be
an impediment to the achievement of the uniform level of certification throughout
Europe, and by different certification bodies, that is expected from the application of
EN 197-2 together with these Guidelines.
This Guidelines Document is based on existing situations for production, evaluation of
conformity and certification of cements. It may happen that certification bodies be
confronted by a situation different to those included in this document. In such a case,
specific procedures should be elaborated on a case by case situation and be approved
and fully recorded by the Certification Body. These specific procedures should always
fulfil the requirements of EN 197-1 and EN 197-2 and lead to the same level of
confidence in product conformity that would be achieved by application of this
Guidelines Document.
Arrangement
The clause numbering system of EN 197-2 is followed. The text of each of the clauses
of the Standard is reproduced in full and is followed by guidance, which is provided
only for those clauses where clarification or elaboration is needed.
CLAUSES OF EN 197-2
Foreword
1 Scope
2 Normative references
3 Definitions
4 Factory production control by the manufacturer
5 Tasks for the certification body
6 Actions in the event of non-conformity
7 Procedure for third party certification of conformity
8 Certificate of conformity and conformity mark
9 Requirements for dispatching centres
Tables 1 and 2
Annexes A and B
2
---------------------- Page: 4 ----------------------
SIST-TP CR 14245:2004
CR 14245:2001 (E)
Foreword
This European Standard has been prepared by Technical Committee CEN/TC 51
"Cement and building limes", the secretariat of which is held by IBN.
This European Standard supersedes ENV 197-2:1995.
Annex A of EN 197-2 is normative, annex B is informative.
According to the CEN/CENELEC Internal Regulations, the national standards
organisations of the following countries are bound to implement this European
Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany,
Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain,
Swede, Switzerland and the United Kingdom.
1 Scope
EN 197-2 specifies the scheme for the evaluation of conformity of cements to their
corresponding product specification standards, including certification of conformity by
a certification body.
The standard provides technical rules for factory production control by the
manufacturer, including autocontrol testing of samples, and for the tasks of the
certifica
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.