Plastics and rubber machines - Blow moulding machines - Safety requirements

This European Standard covers essential health and safety requirements for the design of blow moulding machines for the processing of plastics. The significant hazards inherent in blow moulding machines are listed in Clause 4.
This European Standard does not cover dip blow moulding machines.
This European Standard does not cover hazards due to the use of fluorine or other toxic fluids.
The safety requirements for the interaction between blow moulding machines and ancillary equipment are stipulated. The technical safety requirements for the design of this equipment are not covered.
This European Standard does not cover the requirements for the design of the exhaust system.
The European Standard does not cover noise hazards.
This European Standard is not applicable to blow moulding machines which are manufactured before the date of its publication as an EN. A transition period until 29 December 2009 is foreseen during which the manufacturer may choose to apply either this or the previous version of the standard.

Kunststoff- und Gummimaschinen - Blasformmaschinen - Sicherheitsanforderungen

Diese Europäische Norm behandelt die wesentlichen Gesundheits- und Sicherheitsanforderungen an die
Konstruktion von Blasformmaschinen für die Verarbeitung von Kunststoff. Die signifikanten Gefährdungen an
Blasformmaschinen sind in Abschnitt 4 angegeben.
Diese Europäische Norm behandelt nicht Tauchblasformmaschinen.
Diese Europäische Norm behandelt nicht Gefährdungen durch die Verwendung von Fluor oder anderen
toxischen Fluiden.
Die Sicherheitsanforderungen für das Zusammenwirken zwischen Blasformmaschinen und Zusatzeinrichtungen
werden festgelegt. Die Sicherheitsanforderungen für die Konstruktion dieser Zusatzeinrichtungen
werden nicht behandelt.
Diese Europäische Norm behandelt nicht die Anforderungen an die Gestaltung einer Absaugeinrichtung.
Diese Europäische Norm behandelt nicht die Gefährdungen durch Lärm.
Diese Europäische Norm gilt nicht für Blasformmaschinen, die vor dem Ausgabedatum der Norm hergestellt
wurden. Eine Übergangszeit bis zum 28. Dezember 2009 ist vorgesehen, in der der Hersteller wählen kann,
entweder diese oder die Vorgängerversion der Norm anzuwenden.

Machines pour les matières plastiques et le caoutchouc - Machines de moulage par soufflage - Prescriptions de sécurité

La présente Norme européenne spécifie les prescriptions essentielles de santé et de sécurité relatives à la
conception des machines de moulage par soufflage utilisées dans l’industrie des matières plastiques. Les
phénomènes dangereux significatifs associés aux machines de moulage par soufflage sont énumérés à
l'Article 4.
La présente Norme européenne ne couvre pas les machines de moulage par soufflage de préformes
obtenues par trempage.
La présente Norme européenne ne couvre pas les phénomènes dangereux résultant de l’utilisation de fluor ou
d’autres fluides toxiques.
Les prescriptions de sécurité relatives aux interactions entre les machines de moulage par soufflage et leurs
équipements auxiliaires sont spécifiées. Les prescriptions de sécurité relatives à la conception des
équipements auxiliaires ne sont pas spécifiées.
La présente Norme européenne ne donne pas de prescriptions sur la conception de systèmes d’aspiration.
La présente Norme européenne ne traite pas des phénomènes dangereux dus au bruit.
Ce document n'est pas applicable aux machines de moulage par soufflage fabriquées avant sa date de
publication comme EN. Il est prévu une période de transition allant jusqu’au 29 décembre 2009, pendant
laquelle le constructeur peut choisir d’appliquer soit la présente norme, soit sa version antérieure.

Stroji za predelavo gume in plastike - Pihalni stroji za oblikovanje - Varnostne zahteve

General Information

Status
Published
Publication Date
09-Jun-2009
Withdrawal Date
30-Dec-2009
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
04-Mar-2020

Relations

Buy Standard

Standard
EN 422:2009
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 422:2008
English language
21 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Stroji za predelavo gume in plastike - Pihalni stroji za oblikovanje - Varnostne zahteveKunststoff- und Gummimaschinen - Blasformmaschinen - SicherheitsanforderungenMachines pour les matières plastiques et le caoutchouc - Machines de moulage par soufflage - Prescriptions de sécuritéPlastics and rubber machines - Blow moulding machines - Safety requirements83.200Oprema za gumarsko industrijo in industrijo polimernih materialovEquipment for the rubber and plastics industriesICS:Ta slovenski standard je istoveten z:EN 422:2009SIST EN 422:2009en,fr01-september-2009SIST EN 422:2009SLOVENSKI
STANDARDSIST EN 422:20001DGRPHãþD



SIST EN 422:2009



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 422June 2009ICS 83.200Supersedes EN 422:1995
English VersionPlastics and rubber machines - Blow moulding machines -Safety requirementsMachines pour les matières plastiques et le caoutchouc -Machines de moulage par soufflage - Prescriptions desécuritéKunststoff- und Gummimaschinen - Blasformmaschinen -SicherheitsanforderungenThis European Standard was approved by CEN on 13 May 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 422:2009: ESIST EN 422:2009



EN 422:2009 (E) 2 Contents Page Foreword .4Introduction .51 Scope .62 Normative references .63 Terms and definitions .74 List of significant hazards .84.1 General hazards .84.2 Mechanical hazards related to power operated movements during production . 104.3 Additional hazards associated with machines of specific design . 104.3.1 Machines allowing whole body access . 104.3.2 Rotary machines . 104.4 Additional hazards when using ancillary equipment . 105 Safety requirements and/or protective measures . 105.1 General . 105.1.1 Basic requirements. 105.1.2 Safety distances. 105.1.3 Emergency stop . 115.1.4 Flu
...

SLOVENSKI STANDARD
oSIST prEN 422:2008
01-april-2008
Stroji za predelavo gume in plastike - Pihalni stroji za oblikovanje - Varnostne
zahteve
Plastics and rubber machines - Blow moulding machines - Safety requirements
Kunststoff- und Gummimaschinen - Blasformmaschinen - Sicherheitsanforderungen
Machines pour les matières plastiques et le caoutchouc - Machines de moulage par
soufflage - Prescriptions de sécurité
Ta slovenski standard je istoveten z: prEN 422
ICS:
83.200
oSIST prEN 422:2008 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
DRAFT
prEN 422
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2008
ICS 83.200 Will supersede EN 422:1995
English Version
Plastics and rubber machines - Blow moulding machines -
Safety requirements
Machines pour les matières plastiques et le caoutchouc - Kunststoff- und Gummimaschinen - Blasformmaschinen -
Machines de moulage par soufflage - Prescriptions de Sicherheitsanforderungen
sécurité
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 145.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
: This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
Warning
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 422:2008: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------
prEN 422:2008 (E)
Contents Page
Foreword.4
Introduction .4
1 Scope.4
2 Normative references.5
3 Terms and definitions .6
4 List of significant hazards .7
4.1 General hazards.7
4.2 Mechanical hazards related to power operated movements during production .8
4.3 Additional hazards associated with machines of specific design .8
4.3.1 Machines allowing whole body access .8
4.3.2 Rotary machines.8
4.4 Additional hazards when using ancillary equipment.9
5 Safety requirements and/or protective measures.9
5.1 General.9
5.1.1 Safety distances.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.