EN ISO 10297:2014/A1:2017
(Amendment)Gas cylinders - Cylinder valves - Specification and type testing - Amendment 1: Pressure drums and tubes (ISO 10297:2014/Amd 1:2017)
Gas cylinders - Cylinder valves - Specification and type testing - Amendment 1: Pressure drums and tubes (ISO 10297:2014/Amd 1:2017)
Gasflaschen - Flaschenventile - Spezifikation und Baumusterprüfungen - Änderung 1 (ISO 10297:2014/Amd 1:2017)
Bouteilles à gaz - Robinets de bouteilles - Spécifications et essais de type - Amendement 1: Fûts à pression et tubes (ISO 10297:2014/Amd 1:2017)
Plinske jeklenke - Ventili za jeklenke - Specifikacija in preskus tipa - Dopolnilo A1: Tlačni sodi in velike jeklenke (ISO 10297:2014/Amd 1:2017)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2018
3OLQVNHMHNOHQNH9HQWLOL]DMHNOHQNH6SHFLILNDFLMDLQSUHVNXVWLSD'RSROQLOR$
7ODþQLVRGLLQYHOLNHMHNOHQNH ,62 $PG
Gas cylinders - Cylinder valves - Specification and type testing - Amendment 1: Pressure
drums and tubes (ISO 10297:2014/Amd 1:2017)
Gasflaschen - Flaschenventile - Spezifikation und Baumusterprüfungen - Änderung 1
(ISO 10297:2014/Amd 1:2017)
Bouteilles à gaz - Robinets de bouteilles - Spécifications et essais de type -
Amendement 1: Fûts à pression et tubes (ISO 10297:2014/Amd 1:2017)
Ta slovenski standard je istoveten z: EN ISO 10297:2014/A1:2017
ICS:
23.020.35 Plinske jeklenke Gas cylinders
23.060.40 7ODþQLUHJXODWRUML Pressure regulators
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 10297:2014/A1
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2017
EUROPÄISCHE NORM
ICS 23.020.35; 23.060.40
English Version
Gas cylinders - Cylinder valves - Specification and type
testing - Amendment 1: Pressure drums and tubes (ISO
10297:2014/Amd 1:2017)
Bouteilles à gaz - Robinets de bouteilles - Spécifications Gasflaschen - Flaschenventile - Spezifikation und
et essais de type - Amendement 1: Fûts à pression et Baumusterprüfungen - Änderung 1 (ISO
tubes (ISO 10297:2014/Amd 1:2017) 10297:2014/Amd 1:2017)
This amendment A1 modifies the European Standard EN ISO 10297:2014; it was approved by CEN on 9 February 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10297:2014/A1:2017 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 10297:2014/A1:2017) has been prepared by Technical Committee ISO/TC 58
"Gas cylinders" in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the
secretariat of which is held by BSI.
This Amendment to the European Standard EN ISO 10297:2014 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by October 2017,
and conflicting national standards shall be withdrawn at the latest by October 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 10297:2014/Amd 1:2017 has been approved by CEN as EN ISO 10297:2014/A1:2017
without any modification.
INTERNATIONAL ISO
STANDARD 10297
Third edition
2014-07-15
AMENDMENT 1
2017-03
Gas cylinders — Cylinder valves —
Specification and type testing
AMENDMENT 1: Pressure drums and
tubes
Bouteilles à gaz — Robinets de bouteilles — Spécifications et essais de
type
AMENDEMENT 1: Fûts à pression et tubes
Reference number
ISO 10297:2014/Amd.1:2017(E)
©
ISO 2017
ISO 10297:2014/Amd.1:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
ISO 10297:2014/Amd.1:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expres
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.