Ball valves for thermoplastics piping systems for hot and cold water installations under pressure - Types, dimensions and requirements (ISO/DIS 18984:2024)

This document is applicable to 2-way or multi-way ball valve manufactured with thermoplastic materials to be used for the transport of pressurized water whether or not intended for human consumption (domestic systems) for applications in buildings and utility branches.
              NOTE The two-way valve is generally used for sectioning and control, the multi-way one to divert or mix the flows; information on their functionality can be       
                 found in Appendix B information of ISO 16135.
The application classes are indicated in the relevant hot and cold water system standards.
This document defines the dimensions necessary for the assembly of the valves, ensuring its
interchangeability and defines its physical and mechanical requirements.

Kugelventile für thermoplastische Heiß‑ und Kaltwasserdruckrohrleitungen - Arten, Abmessungen und Anforderungen (ISO/DIS 18984:2024)

Robinets à tournant sphérique pour systèmes de canalisations en matières thermoplastiques pour installations d'eau chaude et froide sous pression - Types, dimensions et exigences (ISO/DIS 18984:2024)

Kroglični ventili za cevne sisteme iz termoplastov za napeljave tople in hladne vode pod tlakom - Vrste, mere in zahteve (ISO/DIS 18984:2024)

General Information

Status
Not Published
Publication Date
26-Aug-2025
Current Stage
4060 - Closure of enquiry - Enquiry
Start Date
24-Apr-2024
Due Date
14-Nov-2024
Completion Date
24-Apr-2024

Buy Standard

Draft
prEN ISO 18984:2024
English language
23 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-april-2024
Kroglični ventili za cevne sisteme iz termoplastov za napeljave tople in hladne
vode pod tlakom - Vrste, mere in zahteve (ISO/DIS 18984:2024)
Ball valves for thermoplastics piping systems for hot and cold water installations under
pressure - Types, dimensions and requirements (ISO/DIS 18984:2024)
Kugelventile für thermoplastische Heiß- und Kaltwasserdruckrohrleitungen - Arten,
Abmessungen und Anforderungen (ISO/DIS 18984:2024)
Robinets à tournant sphérique pour systèmes de canalisations en matières
thermoplastiques pour installations d'eau chaude et froide sous pression - Types,
dimensions et exigences (ISO/DIS 18984:2024)
Ta slovenski standard je istoveten z: prEN ISO 18984
ICS:
23.060.20 Zapirni ventili (kroglasti in Ball and plug valves
pipe)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT INTERNATIONAL STANDARD
ISO/DIS 18984
ISO/TC 138/SC 7 Secretariat: UNI
Voting begins on: Voting terminates on:
2024-01-31 2024-04-24
Ball valves for thermoplastics piping systems for hot
and cold water installations under pressure — Types,
dimensions and requirements
Robinets à tournant sphérique pour systèmes de tuyauterie en materiaux thermoplastiques pour
installations d'eau chaude et froide sous pression — Types, dimensions et exigences
ICS: 23.060.20
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 18984:2024(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2024

ISO/DIS 18984:2024(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 18984
ISO/TC 138/SC 7 Secretariat: UNI
Voting begins on: Voting terminates on:

Ball valves for thermoplastics piping systems for hot
and cold water installations under pressure — Types,
dimensions and requirements
Robinets à tournant sphérique pour systèmes de tuyauterie en materiaux thermoplastiques pour
installations d'eau chaude et froide sous pression — Types, dimensions et exigences
ICS: 23.060.20
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2024
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 18984:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023

ISO/DIS 18984:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Requirements . 4
4.1 Design . 4
4.1.1 Design operating conditions . 4
4.1.2 Function . 4
4.1.3 Design characteristics . 4
4.1.4 Types of valve ends . 5
4.2 Materials . 5
4.2.1 General . 5
4.2.2 Body / Shell material . 5
4.2.3 Valve end materials . 6
4.2.4 Materials for internal components and functional components of the valve . 6
4.2.5 Metal parts . 6
4.2.6 Sealing materials . 6
4.2.7 Greases and lubricants . 6
4.2.8 Adhesives . 6
4.2.9 Assembly. 6
5 Application classes for hot water .6
5.1 Design pressure for the application class . 6
6 Dimensions .7
6.1 Face-to-face dimensions . 7
6.1.1 Joint dimensions of the valve end connections (DN) . 7
6.2 Operation . 7
6.3 Functional characteristics . 7
6.4 Other requirements . 7
6.4.1 Control of the manufacture of body and bonnet/cover . 7
6.4.2 Permanent jointing . 8
6.4.3 Wear . . 8
6.4.4 Operating instructions . 8
7 Marking, Documentation, Storage and transportation . 8
7.1 Marking and documentation . 8
7.2 Preparation for storage and transportation . 9
8 Effect on water quality . 9
Annex A (normative) PP Valve .10
Annex B (normative) PVC-C VALVE .14
Annex C (informative) Determination of Kv .17
Bibliography .18
iii
ISO/DIS 18984:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use
of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereof. As of the date of publication of this document, ISO had not received
notice of (a) patent(s) which may be required to implement this document. However, implementers are
cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/patents. ISO shall not be held responsible for identifying any or all
such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for
the transport of fluids, Subcommittee SC 07, Valves and auxiliary equipment of plastics materials.
Any feedback or questions on this document should be directed to the user’s nationa
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.