EN 16603-10-03:2014

Space engineering - Testing

This standard addresses the requirements for performing verification by testing of space segment elements and space segment equipment on ground prior to launch. The document is applicable for tests performed on qualification models, flight models (tested at acceptance level) and protoflight models.
The standard provides:
•   Requirements for test programme and test management,
•   Requirements for retesting,
•   Requirements for redundancy testing,
•   Requirements for environmental tests,
•   General requirements for functional and performance tests,
NOTE    Specific requirements for functional and performance tests are not part of this standard since they are defined in the specific project documentation.
•   Requirements for qualification, acceptance, and protoflight testing including qualification, acceptance, and proto-fight models’ test margins and duration,
•   Requirements for test factors, test condition, test tolerances, and test accuracies,
•   General requirements for development tests pertinent to the start of the qualification test programme,
NOTE    Development tests are specific and are addressed in various engineering discipline standards.
•   Content of the necessary documentation for testing activities (e.g. DRD).
Due to the specific aspects of the following types of test, this Standard does not address:
•   Space system testing (i.e. testing above space segment element), in particular the system validation test,
•   In-orbit testing,
•   Testing of space segment subsystems,
NOTE    Tests of space segment subsystems are often limited to functional tests that, in some case, are run on dedicated models. If relevant, qualification tests for space segment subsystems are assumed to be covered in the relevant discipline standards.
•   Testing of hardware below space segment equipment levels (including assembly, parts, and components),
•   Testing of stand-alone software,
NOTE    For verification of flight or ground software, ECSS-E-ST-40 and ECSS-Q-ST-80 apply.
•   Qualification testing of two-phase heat transport equipment,
NOTE    For qualification testing of two-phase heat transport equipment, ECSS-E-ST-31-02 applies.
•   Tests of launcher segment, subsystem and equipment, and launch facilities,
•   Tests of facilities and ground support equipment,
•   Tests of ground segment.
This standard may be tailored for the specific characteristic and constrains of a space project in conformance with ECSS-S-ST-00. Annex D gives guidelines for performing this tailoring.

Raumfahrttechnik - Tests

Ingénierie spatiale — Vérification par essai

Vesoljska tehnika - Preskušanje

Standard EN 16603-10-03 določa zahteve za izvajanje preverjanja na tleh s testiranjem vesoljskih elementov in opreme pred izstrelitvijo. Dokument velja za preskuse, izvedene na kvalifikacijskih modelih, modelih za letenje (preskušenih pri sprejemljivostni ravni) in prototipnih modelih za letenje. Standard določa: – zahteve za preskusni program in preskusno upravljanje, – zahteve za ponovno preskušanje, – zahteve za preskušanje redundance, – zahteve za okoljske preskuse, – splošne zahteve za funkcionalne in izvedbene preskuse, – zahteve za kvalifikacije, sprejemljivost in preskušanje prototipnih modelov za letenje, vključno s kvalifikacijami, sprejemljivostjo in preskusnimi mejnimi vrednostmi ter trajanjem preskusa za prototipne modele za letenje, – zahteve za preskusne dejavnike, preskusne pogoje, preskusna odstopanja in preskusno natančnost, – splošne zahteve za razvojne preskuse, ki se nanašajo na začetek kvalifikacijskega preskusnega programa.

General Information

• Status: Withdrawn
• Publication Date: 19-Aug-2014
• Withdrawal Date: 04-Oct-2022
• ICS: 49.140 - Space systems and operations
• Technical Committee: CEN/CLC/TC 5 - Space
• Drafting Committee: CEN/CLC/TC 5 - Space
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 05-Oct-2022
• Mandate: M/496 - Mandate addressed to CEN, CENELEC and ETSI to develop standardisation regarding space industry (Phase 3 of the process)
• Ref Project: SIST EN 16603-10-03:2014 - Space engineering - Testing

Relations

• Replaces: EN 14824:2003 - Space engineering - Testing
• Effective Date: 27-Aug-2014
• Replaced By: EN 16603-10-03:2022 - Space engineering - Testing
• Effective Date: 02-Dec-2020

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 16603-10-03:2014
01-november-2014
1DGRPHãþD
SIST EN 14824:2004
Vesoljska tehnika - Preskušanje
Space engineering - Testing
Raumfahrttechnik - Tests
Ingénerie spatiale - Tests
Ta slovenski standard je istoveten z: EN 16603-10-03:2014
ICS:
49.140 Vesoljski sistemi in operacije Space systems and
operations
SIST EN 16603-10-03:2014 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 16603-10-03:2014

---------------------- Page: 2 ----------------------

SIST EN 16603-10-03:2014


EUROPEAN STANDARD
EN 16603-10-03

NORME EUROPÉENNE

EUROPÄISCHE NORM
August 2014
ICS 49.140 Supersedes EN 14824:2003
English version
Space engineering - Testing
Ingénerie spatiale - Tests Raumfahrttechnik - Tests
This European Standard was approved by CEN on 28 December 2013.

CEN and CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving
this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning
such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN and CENELEC
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN and CENELEC member into its own language and notified to the CEN-CENELEC Management Centre
has the same status as the official versions.

CEN and CENELEC members are the national standards bodies and national electrotechnical committees of Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia,
Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.







CEN-CENELEC Management Centre:
Avenue Marnix 17, B-1000 Brussels
© 2014 CEN/CENELEC All rights of exploitation in any form and by any means reserved Ref. No. EN 16603-10-03:2014 E
worldwide for CEN national Members and for CENELEC
Members.

---------------------- Page: 3 ----------------------

SIST EN 16603-10-03:2014
EN 16603-10-03:2014 (E)
Table of contents
Foreword . 5
Introduction . 6
1 Scope . 8
2 Normative references . 10
3 Terms, definitions and abbreviated terms . 12
3.1 Terms from other standards . 12
3.2 Terms specific to the present standard . 18
3.3 Abbreviated terms. 24
4 General requirements. 27
4.1 Test programme . 27
4.2 Development test prior qualification . 27
4.3 Test management . 28
4.3.1 General . 28
4.3.2 Test reviews . 28
4.3.3 Test documentation . 32
4.3.4 Anomaly or failure during testing . 33
4.3.5 Test data . 33
4.4 Test conditions, tolerances, and accuracies. 33
4.4.1 Test conditions . 33
4.4.2 Test tolerances . 34
4.4.3 Test accuracies .
...