EN ISO 225:2010
(Main)Fasteners - Bolts, screws, studs and nuts - Symbols and descriptions of dimensions (ISO 225:2010)
Fasteners - Bolts, screws, studs and nuts - Symbols and descriptions of dimensions (ISO 225:2010)
ISO 225:2010 defines the symbols and gives descriptions of the dimensions of bolts, screws, studs and nuts in English, French and Russian, for use in the appropriate product standards and drawings.
The figures of the fasteners in ISO 225:2010 are given only as examples.
In addition to terms used in the three official ISO languages (English, French and Russian), ISO 225:2010 gives the equivalent terms in Chinese, German, Italian, Japanese, Spanish and Swedish.
Mechanische Verbindungselemente - Schrauben und Muttern - Bemaßung (ISO 225:2010)
Éléments de fixation - Vis, goujons et écrous - Symboles et description des dimensions (ISO 225:2010)
L'ISO 225:2010 définit les symboles et la description des dimensions des vis, goujons, tiges filetées et écrous, pour utilisation dans les normes de produits appropriées et les spécifications sur plan.
Les figures des éléments de fixation de l'ISO 225:2010 ne sont données qu'à titre d'exemples.
En complément des termes utilisés dans les trois langues officielles de l'ISO (anglais, français et russe), l'ISO 225:2010 donne les termes équivalents en chinois, allemand, italien, japonais, espagnol et suédois.
Vezni elementi - Vijaki in matice - Oznake in opisi mer (ISO 225:2010)
Ta mednarodni standard opredeljuje oznake in podaja opise mer vijakov in matic, ki se uporabljajo v ustreznih standardih in risbah izdelkov.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2012
1DGRPHãþD
SIST EN 20225:1996
Vezni elementi - Vijaki in matice - Oznake in opisi mer (ISO 225:2010)
Fasteners - Bolts, screws, studs and nuts - Symbols and designations of dimensions
(ISO 225:2010)
Mechanische Verbindungselemente - Schrauben und Muttern - Bemaßung (ISO
225:2010)
Éléments de fixation - Vis, goujons et écrous - Symboles et désignations des dimensions
(ISO 225:2010)
Ta slovenski standard je istoveten z: EN ISO 225:2010
ICS:
01.040.21 Mehanski sistemi in deli za Mechanical systems and
splošno rabo (Slovarji) components for general use
(Vocabularies)
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
21.060.20 Matice Nuts
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 225
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2010
ICS 21.060.10 Supersedes EN 20225:1991
English Version
Fasteners - Bolts, screws, studs and nuts - Symbols and
descriptions of dimensions (ISO 225:2010)
Éléments de fixation - Vis, goujons et écrous - Symboles et Mechanische Verbindungselemente - Schrauben und
description des dimensions (ISO 225:2010) Muttern - Bemaßung (ISO 225:2010)
This European Standard was approved by CEN on 25 September 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 225:2010: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
The text of ISO 225:2010 has been prepared by Technical Committee ISO/TC 2 “Fasteners” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 225:2010 by
Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2011, and conflicting national standards shall be withdrawn at the
latest by April 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 20225:1991.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 225:2010 has been approved by CEN as a EN ISO 225:2010 without any modification.
INTERNATIONAL ISO
STANDARD 225
NORME
Third edition
Troisième édition
INTERNATIONALE
Tретье изданиe
2010-10-01
МЕЖДУНАРОДНЫЙ
СТАНДАРТ
Fasteners — Bolts, screws, studs and
nuts — Symbols and descriptions of
dimensions
Éléments de fixation — Vis, goujons et
écrous — Symboles et description des
dimensions
Крепежные изделия — Болты, винты,
шпильки и гайки — Символы и
обозначения размеров
Mechanische Verbindungselemente —
Schrauben und Muttern — Symbole und
Bemaßung
Reference number
Numéro de référence
Номер ссылки
ISO 225:2010(E/F/R)
©
ISO 2010
ISO 225:2010(E/F/R)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier peut
être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence autorisant
l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées acceptent de fait la
responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute responsabilité en la
matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info du
fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir l'exploitation de
ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation, veuillez en informer le
Secrétariat central à l'adresse donnée ci-dessous.
PDF – Oсвoбoждeниe oт oбязaннoсти
Нaстoящий фaйл PDF мoжeт сoдeржaть интeгрирoвaнныe шрифты. В сooтвeтствии с лицeнзиoнными услoвиями фирмы Adobe, этoт
фaйл мoжeт быть oтпeчaтaн или визуaлизирoвaн, oднaкo oн нe дoлжeн быть измeнeн, зa исключeниeм случaeв, кoгдa примeняeмый
для этoй цeли кoмпьютeр имeeт прaвo нa испoльзoвaниe этиx шрифтoв и eсли эти пoслeдниe инстaллирoвaны. Зaгружeниeм
нaстoящeгo фaйлa зaинтeрeсoвaнныe стoрoны сoглaшaются принять нa сeбя oтвeтствeннoсть зa сoблюдeниe лицeнзиoнныx
услoвий фирмы Adobe. Цeнтрaльный сeкрeтaриaт ИСO нe нeсeт никaкoй oтвeтствeннoсти в этoм oтнoшeнии.
Adobe являeтся тoргoвым знaкoм фирмы Adobe Systems Incorporated.
Дeтaли, oтнoсящиeся к прoгрaммнoму oбeспeчeнию и испoльзoвaнныe для сoздaния нaстoящeгo фaйлa PDF, мoгут быть
прoкoнсультирoвaны в рубрикe General Info фaйлa; пaрaмeтры для сoздaния PDF были oптимизирoвaны для пeчaти. Были приняты
всe нeoбxoдимыe мeры, чтoбы гaрaнтирoвaть пoльзoвaниe нaстoящим фaйлoм всeми члeнaми ИСO. В рeдкиx случaяx, кoгдa мoгли
бы вoзникнуть прoблeмы испoльзoвaния, прoсьбa инфoрмирoвaть Цeнтрaльный сeкрeтaриaт пo aдрeсу, привeдeннoму нижe.
DOCUMENT PROTÉGÉ PAR COPYRIGHT
ДОКУМЕНТ ОХРАНЯЕМЫЙ АВТОРСКИМ ПРАВОМ
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester. / Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être
reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les
microfilms, sans l'accord écrit de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur. / Всe прaвa сoxрaнeны.
Eсли нe укaзaнo иным oбрaзoм, никaкaя чaсть нaстoящeй публикaции нe мoжeт быть кoпирoвaнa или испoльзoвaнa в кaкoй-либo
фoрмe или кaким-либo элeктрoнным или мexaничeским спoсoбoм, включaя фoтoкoпии и микрoфильмы, бeз прeдвaритeльнoгo
письмeннoгo сoглaсия ИСO, кoтoрoe дoлжнo быть пoлучeнo пoслe зaпрoсa o рaзрeшeнии, нaпрaвлeннoгo пo aдрeсу, прeвeдeннoму
нижe или в кoмитeт-члeн ИСO в стрaнe зaинтeрeсoвaннoгo.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland/Publié en Suisse/Oтпeчaтaнo в Швeйцaрии
ii © ISO 2010 – All rights reserved/Tous droits réservés/Все права сохранены
ISO 225:2010(E/F/R)
Contents Page
Foreword.vii
1 Scope .2
2 Normative reference.2
3 Bolts, screws and studs.4
3.1 Hexagon head products.4
3.1.1 Hexagon head bolts and screws.4
3.1.2 Hexagon head bolts and screws with flange.7
3.2 Hexagon socket head screws .8
3.2.1 Cylindrical head .8
3.2.2 Countersunk head .9
3.2.3 Button head.10
3.3 Hexalobular socket head screws.11
3.3.1 Cylindrical head .11
3.3.2 Cheese head.12
3.3.3 Pan head.13
3.3.4 Raised countersunk head.13
3.4 Triple square socket head screws.14
3.4.1 Cylindrical head .14
3.4.2 Cylindrical head with flange .15
3.4.3 Raised countersunk head.16
3.5 Cup head square neck bolts.17
3.6 Slotted and cross-recessed head screws.18
3.7 Studs.20
3.8 Set screws .21
3.9 Headless screws with shank .21
3.10 Ends of parts with external thread (points) .22
3.11 Thread rolling (thread forming) screws.24
3.12 Thread cutting screws.25
3.13 Tapping screws.26
3.14 Drilling screws with tapping screw thread.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.