EN ISO 13349-2:2022
(Main)Fans - Vocabulary and definitions of categories - Part 2: Categories (ISO 13349-2:2022)
Fans - Vocabulary and definitions of categories - Part 2: Categories (ISO 13349-2:2022)
This document defines categories in the field of fans used for all purposes.
It is not applicable to electrical safety.
Ventilatoren - Terminologie und Klassifizierung - Teil 2: Klassifizierung (ISO 13349-2:2022)
Dieses Dokument definiert Kategorien von Ventilatoren für alle Anwendungen.
Es ist nicht anwendbar in Bezug auf die elektrische Sicherheit.
Ventilateurs - Vocabulaire et définitions des catégories - Partie 2: Catégories (ISO 13349-2:2022)
Le présent document définit les catégories dans le domaine des ventilateurs destinés à tous les usages.
Le présent document ne s’applique pas à la sécurité électrique.
Ventilatorji - Slovar in definicije kategorij - 2. del: Kategorije (ISO 13349-2:2022)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2022
Nadomešča:
SIST EN ISO 13349:2010
Ventilatorji - Slovar in definicije kategorij - 2. del: Kategorije (ISO 13349-2:2022)
Fans - Vocabulary and definitions of categories - Part 2: Categories (ISO 13349-2:2022)
Ventilateurs - Vocabulaire et définitions des catégories - Partie 2: Catégories (ISO 13349
-2:2022)
Ta slovenski standard je istoveten z: EN ISO 13349-2:2022
ICS:
01.040.23 Tekočinski sistemi in sestavni Fluid systems and
deli za splošno rabo (Slovarji) components for general use
(Vocabularies)
23.120 Zračniki. Vetrniki. Klimatske Ventilators. Fans. Air-
naprave conditioners
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 13349-2
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2022
EUROPÄISCHE NORM
ICS 01.040.23; 23.120 Supersedes EN ISO 13349:2010
English Version
Fans - Vocabulary and definitions of categories - Part 2:
Categories (ISO 13349-2:2022)
Ventilateurs - Vocabulaire et définitions des catégories
- Partie 2: Catégories (ISO 13349-2:2022)
This European Standard was approved by CEN on 4 September 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13349-2:2022 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 13349-2:2022) has been prepared by Technical Committee ISO/TC 117 "Fans"
in collaboration with Technical Committee CEN/TC 156 “Ventilation for buildings” the secretariat of
which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2023, and conflicting national standards shall be
withdrawn at the latest by April 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 13349:2010.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 13349-2:2022 has been approved by CEN as EN ISO 13349-2:2022 without any
modification.
INTERNATIONAL ISO
STANDARD 13349-2
First edition
2022-09
Fans — Vocabulary and definitions of
categories —
Part 2:
Categories
Ventilateurs — Vocabulaire et définitions des catégories —
Partie 2: Catégories
Reference number
ISO 13349-2:2022(E)
ISO 13349-2:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 13349-2:2022(E)
Contents Page
Foreword .iv
Introduction .v
1 S c op e . 1
2 N ormative references . 1
3 T erms and definitions . 1
4 S ymbols and units. 1
4.1 Symbols . 1
4.2 M ultiples of primary units . 2
4.3 U nits of time . 2
4.4 T emperature of air or gas. 2
5 F an categories . 2
5.1 G eneral . 2
5.2 S uitability for the fan pressure . 3
5.2.1 G eneral . 3
5.2.2 W ork per unit mass . 3
5 . 2 . 3 Fa n c at e g or ie s . 3
5.2.4 C hanges in air density . 3
5.3 S uitability of construction . 4
5.3.1 Categorization according to casing construction . 4
5.3.2 D esignation for hot-gas fan . 4
5.3.3 Designation and recommended categorization for smoke-ventilating fans . 5
5.3.4 C ategorization for gas-tight fans . 5
5 .4 Tr a n s m i s s ion a r r a n g ement s . 5
5.5 I nlet and outlet conditions . 9
5.6 M ethod of fan control . 10
5.7 D esignation of direction of rotation and position of parts of the fan assembly . 10
5.7.1 General . 10
5.7.2 D irection of rotation . 10
5.7.3 O utlet position of a centrifugal fan .12
5.7.4 Position of component parts of a centrifugal fan with volute casing .13
5.7.5 P osition of component parts of an axial-flow, mixed-flow or other fan with
coaxial inlet and outlet .13
5.7.6 P osition of motor or other prime movers . 14
5.8 C haracteristic dimensions and component parts . 16
5 . 8 .1 C h a r ac t er i s t ic d i men s ion s . 16
5.8.2 Terms for fan component parts . 16
Annex A (informative) Examples .24
Bibliography .26
iii
ISO 13349-2:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.