iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN ISO 4033:2012

(Main)

Hexagon high nuts (style 2) - Product grades A and B (ISO 4033:2012)

Hexagon high nuts (style 2) - Product grades A and B (ISO 4033:2012)

ISO 4033:2012 specifies the characteristics of hexagon high nuts (style 2), with threads from M5 up to and including M36, with product grade A for threads of diameter less than or equal to M16 and product grade B for threads of diameter greater than M16.

Hohe Sechskantmuttern (Typ 2) - Produktklassen A und B (ISO 4033:2012)

Diese Internationale Norm legt Eigenschaften von hohen Sechskantmuttern (Typ 2) mit Gewinden von M5 bis M36, in Produktklasse A für Gewinde D  M16 und Produktklasse B für Gewinde D  M16, fest.
Falls in besonderen Fällen andere Festlegungen als die in dieser Internationalen Norm aufgeführten benötigt werden, können diese den entsprechenden Internationalen Normen entnommen werden, z. B. ISO 724, ISO 898 2, ISO 965 1 und ISO 4759 1.
ANMERKUNG   Für Sechskantmuttern mit normaler Höhe (Typ 1), siehe ISO 4032.

Écrous hexagonaux hauts (style 2) - Grades A et B (ISO 4033:2012)

L'ISO 4033:2012 spécifie les caractéristiques des écrous hexagonaux hauts (style 2), de diamètres de filetage M5 à M36 inclus, de grade A pour les filetages de diamètre inférieur ou égal à M16 et de grade B pour les filetages de diamètre supérieur à M16.

Šestrobe matice, tip 2 - Razreda izdelave A in B (ISO 4033:2012)

Ta mednarodni standard določa značilnosti šestrobih matic (tip 2) z navoji od M5 do vključno M36, z razredom izdelave A za navoje D ≤ M16 in razredom izdelave B za navoje D > M16. Če so v posebnih primerih zahtevane specifikacije, ki niso navedene v tem mednarodnem standardu, jih je mogoče izbrati iz obstoječih mednarodnih standardov, na primer standardov ISO 724, ISO 898-2, ISO 965-1 in ISO 4759-1.

General Information

Status
Withdrawn
Publication Date
18-Dec-2012
Withdrawal Date
05-Sep-2023
ICS
21.060.10 - Bolts, screws, studs
21.060.20 - Nuts
Technical Committee
CEN/TC 185 - Threaded and nonthreaded mechanical fasteners and accessories
Drafting Committee
CEN/TC 185 - Threaded and nonthreaded mechanical fasteners and accessories
Current Stage
Ref Project
SIST EN ISO 4033:2014 - Hexagon nuts, style 2 - Product grades A and B (ISO 4033:2012)

Relations

Replaces
EN ISO 4033:2000 - Hexagon nuts, style 2 - Product grades A and B (ISO 4033:1999)
Effective Date
26-Dec-2012
Replaced By
EN ISO 4033:2023 - Fasteners - Hexagon high nuts (style 2) (ISO 4033:2023)
Effective Date
28-Jan-2023
Revised
prEN ISO 4033 - Hexagon high nuts (style 2) - Product grades A and B (ISO/DIS 4033:2016)
Effective Date
19-Jan-2023

Buy Standard

EN ISO 4033:2014EN ISO 4033:2014
PreviousNext
Standard
EN ISO 4033:2014
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-julij-2014
1DGRPHãþD
SIST EN ISO 4033:2002
Šestrobe matice, tip 2 - Razreda izdelave A in B (ISO 4033:2012)
Hexagon nuts, style 2 - Product grades A and B (ISO 4033:2012)
Sechskantmuttern, Typ 2 - Produktklassen A und B (ISO 4033:2012)
Écrous hexagonaux, style 2 - Grades A et B (ISO 4033:2012)
Ta slovenski standard je istoveten z: EN ISO 4033:2012
ICS:
21.060.20 Matice Nuts
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 4033
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2012
ICS 21.060.20 Supersedes EN ISO 4033:2000
English Version
Hexagon high nuts (style 2) - Product grades A and B (ISO
4033:2012)
Écrous hexagonaux hauts (style 2) - Grades A et B (ISO Sechskantmuttern, Typ 2 - Produktklassen A und B (ISO
4033:2012) 4033:2012)
This European Standard was approved by CEN on 13 November 2012.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4033:2012: E
worldwide for CEN national Members.

Contents Page
Foreword . 3

Foreword
This document (EN ISO 4033:2012) has been prepared by Technical Committee ISO/TC 2 "Fasteners" in
collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2013, and conflicting national standards shall be withdrawn at
the latest by June 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 4033:2000.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 4033:2012 has been approved by CEN as a EN ISO 4033:2012 without any modification.

INTERNATIONAL ISO
STANDARD 4033
Third edition
2012-12-15
Hexagon high nuts (style 2) — Product
grades A and B
Écrous hexagonaux hauts (style 2) — Grades A et B
Reference number
ISO 4033:2012(E)
©
ISO 2012
ISO 4033:2012(E)
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved

ISO 4033:2012(E)
Contents Page
Foreword .iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Dimensions . 1
4 Requirements and reference International Standards . 4
5 Designation . 4
Bibliography . 5
ISO 4033:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 4033 was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 12, Fasteners with
metric internal thread.
This third edition cancels and replaces the second edition (ISO 4033:1999), of which it constitutes a minor revision.
iv © ISO 2012 – All rights reserved

ISO 4033:2012(E)
Introduction
This International Standard belongs to a complete group of product standards developed b
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 14399-3:2015(Main)
High-strength structural bolting assemblies for preloading - Part 3: System HR - Hexagon bolt and nut assemblies
SIST EN 14399-3:2015

This European Standard specifies, together with EN 14399 1 and EN 14399 2, the requirements for assemblies of high-strength structural bolts and nuts of system HR suitable for preloaded joints with large widths across flats, thread sizes M12 to M36 and property classes 8.8/8 or 8.8/10 and 10.9/10.
Bolting assemblies in accordance with this document have been designed to allow preloading of at least 0,7 fub × As  ) according to EN 1993 1 8 (Eurocode 3) and to obtain ductility predominantly by plastic elongation of the bolt. For this purpose the components have the following characteristics:
-   normal nut height (style 1), see EN ISO 4032;
-   thread length of the bolt according to ISO 888.
Bolting assemblies in accordance with this document include washers according to EN 14399 6 or to EN 14399 5 (under the nut only).
NOTE   Attention is drawn to the importance of ensuring that bolting assemblies are correctly used if satisfactory results are to be obtained. For recommendations concerning proper application, reference to EN 1090-2 is made.
General requirements and requirements for suitability for preloading are specified in EN 14399 2.
Clamp lengths and grip lengths for the bolting assemblies are specified in the normative Annex A.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 225:2010(Main)
Fasteners - Bolts, screws, studs and nuts - Symbols and descriptions of dimensions (ISO 225:2010)
SIST EN ISO 225:2012

ISO 225:2010 defines the symbols and gives descriptions of the dimensions of bolts, screws, studs and nuts in English, French and Russian, for use in the appropriate product standards and drawings.
The figures of the fasteners in ISO 225:2010 are given only as examples.
In addition to terms used in the three official ISO languages (English, French and Russian), ISO 225:2010 gives the equivalent terms in Chinese, German, Italian, Japanese, Spanish and Swedish.

  • Standard
    70 pages
    English, French, German and Russian language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14831:2005(Main)
Fasteners - Tightening performance - Torque/Angle simplified test method
SIST EN 14831:2005

This European standard specifies a test method for fasteners with ISO metric thread from M6 to M16 and with property classes 8.8 to 12.9 for bolts and screws and with property classes 8 to 12 for nuts, to check their tightening performance in the elastic range.
It applies to steel fasteners with an ISO metric thread according to ISO 68-1.
It applies to fasteners having a friction coefficient from 0,06 up to and including 0,18. For higher values of friction coefficients, the dispersion of test results increases and the test method should not be applied. For lower values friction of coefficients, which are for very specific applications and require special lubrication, this standard does not apply.
This comparative test method can be used to monitor stability of a production process (such as coating, lubrication, shot-blasting) or to compare various production manufacturing lots. It can also be used to detect fasteners, which are out of specification.
NOTE   This simplified test method has been developed to avoid systematic use of more complex procedures.
In case of dispute the torque/tension test method according to EN ISO 16047 is the referee test.
This standard does not apply for assessment of fasteners in actual assembly conditions; it does not allow the measurement of operating friction coefficients.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 28839:1991(Main)
Mechanical properties of fasteners - Bolts, screws, studs and nuts made of non-ferrous metals (ISO 8839:1986)
SIST EN 28839:2000

Specifies the mechanical properties of products: with nominal thread diameters from M 1,6 to M 39 inclusive, with metric ISO thread in accordance with ISO 261, made of copper and copper alloys or aluminium and aluminium alloys; it does not apply to products with special property requirements.

  • Standard
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1515-4:2021/AC:2022(Corrigendum)
Flanges and their joints - Bolting - Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 2014/68/EU
SIST EN 1515-4:2021/AC:2022

This document is applicable to the selection of bolting for flanged joints on equipment subject to the Pressure Equipment Directive 2014/68/EU.
It specifies standards and additional requirements for dimensions, material properties and technical conditions of delivery for bolting.
NOTE 1   Washers are not within the scope of this document.
The selection is based on commonly used bolting. It covers common temperature ranges of the general service of flanges.
When selecting bolting according to this document it is essential to take into account environmental conditions and other parameters including type of fluids, corrosion hazards, sour service, low temperature brittle failure and relaxation at elevated temperatures.
The purpose of this document is to provide a selection of most commonly used bolting types and bolting material combinations.
It is not the intention to specify all possible applications but to give guidance on the most common applications. For example, application limits for material in the creep range are not explicitly covered in this document. Where material standard provides mechanical properties for the creep range respective reference is made in Table 3.
NOTE 2   Special services and ambient conditions may require the application of coatings. It is the purchaser’s option to decide on this. Depending on the coating used, a verification of the temperature ranges given in Table 3 and Table 4 may be required.
NOTE 3   In Annex B there are bolting types and bolting material combinations according to commonly used national standards other than those listed in Table 2, Table 3 and Table 4.

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1515-4:2021(Main)
Flanges and their joints - Bolting - Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 2014/68/EU
SIST EN 1515-4:2021

This document is applicable to the selection of bolting for flanged joints on equipment subject to the Pressure Equipment Directive 2014/68/EU.
It specifies standards and additional requirements for dimensions, material properties and technical conditions of delivery for bolting.
NOTE 1   Washers are not within the scope of this document.
The selection is based on commonly used bolting. It covers common temperature ranges of the general service of flanges.
When selecting bolting according to this document it is essential to take into account environmental conditions and other parameters including type of fluids, corrosion hazards, sour service, low temperature brittle failure and relaxation at elevated temperatures.
The purpose of this document is to provide a selection of most commonly used bolting types and bolting material combinations.
It is not the intention to specify all possible applications but to give guidance on the most common applications. For example, application limits for material in the creep range are not explicitly covered in this document. Where material standard provides mechanical properties for the creep range respective reference is made in Table 3.
NOTE 2   Special services and ambient conditions may require the application of coatings. It is the purchaser’s option to decide on this. Depending on the coating used, a verification of the temperature ranges given in Table 3 and Table 4 may be required.
NOTE 3   In Annex B there are bolting types and bolting material combinations according to commonly used national standards other than those listed in Table 2, Table 3 and Table 4.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14399-3:2015(Main)
High-strength structural bolting assemblies for preloading - Part 3: System HR - Hexagon bolt and nut assemblies
SIST EN 14399-3:2015

This European Standard specifies, together with EN 14399 1 and EN 14399 2, the requirements for assemblies of high-strength structural bolts and nuts of system HR suitable for preloaded joints with large widths across flats, thread sizes M12 to M36 and property classes 8.8/8 or 8.8/10 and 10.9/10.
Bolting assemblies in accordance with this document have been designed to allow preloading of at least 0,7 fub × As  ) according to EN 1993 1 8 (Eurocode 3) and to obtain ductility predominantly by plastic elongation of the bolt. For this purpose the components have the following characteristics:
-   normal nut height (style 1), see EN ISO 4032;
-   thread length of the bolt according to ISO 888.
Bolting assemblies in accordance with this document include washers according to EN 14399 6 or to EN 14399 5 (under the nut only).
NOTE   Attention is drawn to the importance of ensuring that bolting assemblies are correctly used if satisfactory results are to be obtained. For recommendations concerning proper application, reference to EN 1090-2 is made.
General requirements and requirements for suitability for preloading are specified in EN 14399 2.
Clamp lengths and grip lengths for the bolting assemblies are specified in the normative Annex A.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 225:2010(Main)
Fasteners - Bolts, screws, studs and nuts - Symbols and descriptions of dimensions (ISO 225:2010)
SIST EN ISO 225:2012

ISO 225:2010 defines the symbols and gives descriptions of the dimensions of bolts, screws, studs and nuts in English, French and Russian, for use in the appropriate product standards and drawings.
The figures of the fasteners in ISO 225:2010 are given only as examples.
In addition to terms used in the three official ISO languages (English, French and Russian), ISO 225:2010 gives the equivalent terms in Chinese, German, Italian, Japanese, Spanish and Swedish.

  • Standard
    70 pages
    English, French, German and Russian language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14831:2005(Main)
Fasteners - Tightening performance - Torque/Angle simplified test method
SIST EN 14831:2005

This European standard specifies a test method for fasteners with ISO metric thread from M6 to M16 and with property classes 8.8 to 12.9 for bolts and screws and with property classes 8 to 12 for nuts, to check their tightening performance in the elastic range.
It applies to steel fasteners with an ISO metric thread according to ISO 68-1.
It applies to fasteners having a friction coefficient from 0,06 up to and including 0,18. For higher values of friction coefficients, the dispersion of test results increases and the test method should not be applied. For lower values friction of coefficients, which are for very specific applications and require special lubrication, this standard does not apply.
This comparative test method can be used to monitor stability of a production process (such as coating, lubrication, shot-blasting) or to compare various production manufacturing lots. It can also be used to detect fasteners, which are out of specification.
NOTE   This simplified test method has been developed to avoid systematic use of more complex procedures.
In case of dispute the torque/tension test method according to EN ISO 16047 is the referee test.
This standard does not apply for assessment of fasteners in actual assembly conditions; it does not allow the measurement of operating friction coefficients.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1515-2:2001(Main)
Flanges and their joints - Bolting - Part 2: Classification of bolt materials for steel flanges, PN designated
SIST EN 1515-2:2002

This European Standard covers the classification of bolt materials combination with the flange material groups of steel flanges prEN 1092-1 (PN-designated).
Bolt materials are listed in EN 1515-1, flange material groups are listed in prEN 1092-1.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day