CEN/TS 12200-2:2017
(Main)Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity
Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity
This part of EN 12200 gives guidance for the assessment of conformity of formulations, products, joints and assemblies in accordance with EN 12200 1:2016 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of third-party certification procedures.
NOTE In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with EN 12200 1:2016, this document is applicable to piping systems made of unplasticized poly(vinyl chloride) (PVC-U) intended to be used for above ground external rainwater, and to fittings and brackets made of acrylic materials which may be used in combination with the pipes.
Kunststoff-Rohrleitungssysteme für außenliegende Regenfallleitungen - Weichmacherfreies Polyvinylchlorid (PVC-U) - Teil 2: Empfehlungen für die Beurteilung der Konformität
Dieser Teil der EN 12200 gibt Empfehlungen für die Beurteilung der Konformität von Formmassen, Erzeugnissen, Verbindungen und Bauteilkombinationen, die, in Übereinstimmung mit EN 12200-1:2016, für eine Einbeziehung in den Qualitätssicherungsplan des Herstellers als Teil des Qualitätsmanagementsystems und für die Erstellung von Drittstellenzertifizierungsverfahren vorgesehen sind.
ANMERKUNG Zur Unterstützung des Lesers enthält Anhang A einen Überblick über das Prüfsystem.
Dieses Dokument gilt in Verbindung mit EN 12200-1:2016 für Rohrleitungssysteme aus weichmacherfreiem Polyvinylchlorid (PVC-U), die für außen liegende Regenfallleitungen vorgesehen sind, und für Formstücke und Rohrschellen aus Acrylwerkstoffen, die in Verbindung mit den Rohren verwendet werden dürfen.
Systèmes de canalisations de descentes d’eaux pluviales en plastique à usage externe en aérien - Poly(chlorure de vinyle) non plastifié (PVC-U) - Partie 2 : Guide pour l'évaluation de la conformité
Cevni sistemi iz polimernih materialov za odvod padavinskih voda za zunanjo uporabo - Nemehčan polivinilklorid (PVC-U) - 2. del: Smernice za ugotavljanje skladnosti
Ta del standarda EN 12200 vsebuje navodila za ugotavljanje skladnosti formulacij, izdelkov, spojev in sestavov s standardom EN 12200 1:2016, ki naj bi se vključila v poslovnik kakovosti proizvajalca kot del sistema vodenja kakovosti, vsebuje pa tudi navodila za vzpostavitev postopka certificiranja, ki ga izvajajo tretje osebe.
OPOMBA V pomoč bralcem dodatek A vsebuje osnovno preskusno matriko.
Ta dokument se v povezavi s standardom EN 12200 1:2016 uporablja za cevne sisteme iz nemehčanega polivinilklorida (PVC-U), ki so namenjeni za uporabo kot nadzemni zunanji sistemi za padavinske vode, ter za fitinge in nosilce iz akrilnih materialov, ki se lahko uporabljajo skupaj s cevmi.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2017
1DGRPHãþD
SIST- TS CEN/TS 12200-2:2003
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY]DRGYRGSDGDYLQVNLKYRGD]D]XQDQMR
XSRUDER1HPHKþDQSROLYLQLONORULG 39&8 GHO 6PHUQLFH]DXJRWDYOMDQMH
VNODGQRVWL
Plastics rainwater piping systems for above ground external use - Unplasticized poly
(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity
Kunststoff-Rohrleitungssysteme für außenliegende Regenfalleitungen -
Weichmacherfreies Polyvinylchlorid (PVC-U) - Teil 2: Empfehlungen für die Beurteilung
der Konformität
Systèmes de canalisations de descentes d’eaux pluviales en plastique à usage externe
en aérien - Poly(chlorure de vinyle) non plastifié (PVC-U) - Partie 2 : Guide pour
l'évaluation de la conformité
Ta slovenski standard je istoveten z: CEN/TS 12200-2:2017
ICS:
23.040.03 Cevovodi za zunanje sisteme Pipeline and its parts for
transporta vode in njihovi deli external water conveyance
systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
CEN/TS 12200-2
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
February 2017
TECHNISCHE SPEZIFIKATION
ICS 23.040.05 Supersedes CEN/TS 12200-2:2003
English Version
Plastics rainwater piping systems for above ground
external use - Unplasticized poly(vinyl chloride) (PVC-U) -
Part 2: Guidance for the assessment of conformity
Systèmes de canalisations de descentes d'eaux Kunststoff-Rohrleitungssysteme für außenliegende
pluviales en plastique à usage externe en aérien - Regenfallleitungen - Weichmacherfreies
Poly(chlorure de vinyle) non plastifié (PVC-U) - Partie Polyvinylchlorid (PVC-U) - Teil 2: Empfehlungen für
2 : Guide pour l'évaluation de la conformité die Beurteilung der Konformität
This Technical Specification (CEN/TS) was approved by CEN on 4 December 2016 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 12200-2:2017 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions, . 6
4 Abbreviated terms . 9
5 General . 9
6 Testing and inspection . 9
6.1 Material specification . 9
6.1.1 PVC-U material . 9
6.1.2 Acrylic material . 10
6.1.3 Other material . 11
6.2 Grouping . 11
6.2.1 General . 11
6.2.2 Size groups . 11
6.2.3 Fitting groups . 11
6.3 Type testing . 11
6.4 Batch release tests . 14
6.5 Process verification tests . 15
6.6 Audit tests . 16
6.7 Indirect tests (IT) . 18
6.8 Test records . 18
Annex A (informative) Basic test matrix . 19
Bibliography . 20
European foreword
This document (CEN/TS 12200-2:2017) has been prepared by Technical Committee CEN/TC 155
“Plastics piping systems and ducting systems”, the secretariat of which is held by NEN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes CEN/TS 12200-2:2003.
Compared with CEN/TS 12200-2:2003, the following changes have been made:
a) use of the template drafted by CEN/TC 155/WG 21 for assessment of conformity documents
(change of “Terms and definitions” and addition of 1 column “Sampling procedures” in Tables);
b) introduction of “Limits of addition of PVC reprocessed and recycled material” in a separate table
(Table 2);
c) addition of an informative Annex A: Basic test matrix.
EN 12200 consists of the following Parts, under the general title “Plastics rainwater piping systems for
above ground external use — Unplasticized poly (vinyl chloride) (PVC-U)”.
— Part 1: Specifications for pipes, fittings and the system;
— Part 2: Guidance for the assessment of conformity;
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to announce this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
the United Kingdom.
Introduction
Figures 1 and 2 are intended to provide general information on the concept of testing and organization
of those tests used for the purpose of the assessment of conformity. For each type of test, i.e. type test
(TT), batch release test (BRT), process verification test (PVT) and audit test (AT), this part of EN 12200
details the applicable characteristics to be assessed and the frequency and sampling of testing.
A typical scheme for the assessment of conformity of materials (formulations), pipes, fittings or
assemblies by manufacturers is given in Figure 1.
Figure 1 — Typical scheme for the assessment of conformity by a manufacturer
A typical scheme for the assessment of conformity of materials (formulations), pipes, fittings, valves or
assemblies by manufacturers, including a third-party certification, is given in Figure 2.
Figure 2 — Typical scheme for the assessment of conformity by a manufacturer, including
certification
1 Scope
This part of EN 12200 gives guidance for the assessment of conformity of formulations, products, joints
and assemblies in accordance with EN 12200-1:2016 intended to be included in the manufacturer’s
quality plan as part of the quality management system and for the establishment of third-party
certification procedures.
NOTE In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with EN 12200-1:2016, this document is applicable to piping systems made of
unplasticized poly(vinyl chloride) (PVC-U) intended to be used for above ground external rainwater,
and to fittings and brackets made of acrylic materials which may be used in combination with the pipes.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
EN 12200-1:2016, Plastics rainwater piping systems for above ground external use - Unplasticized
poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
3 Terms and definitions,
For the purposes of this document, the terms and definitions given in EN 12200-1:2016, and the
following apply.
3.1
certification body
impartial body, governmental or non-governmental, possessing the necessary competence and
responsibility to carry out certification of conformity according to given rules of procedure and
management
Note 1 to entry: A certification body is preferably accredited to EN ISO/IEC 17021 [2].
3.2
inspection body
body, that performs inspection
[SOURCE: EN ISO/IEC 17020:2012 [3], 2.2]
Note 1 to entry: A body can be an organization, or part of an organization.
Note 2 to entry: A inspection body is preferably compliant with EN ISO/IEC 17020 [3].
3.3
testing laboratory
laboratory which measures, tests, calibrates or otherwise determines the characteristics of the
performance of materials and products
Note 1 to entry: In the context of this part of EN 12202, the materials and products can be subjected to type
testing, batch release testing, process verification testing, audit testing, and witness testing, as applicable.
Note 2 to entry: A testing laboratory is preferably compliant with EN ISO/IEC 17025 [4].
3.4
quality management system
management system to direct and control an organization with regard to quality
[SOURCE: EN ISO 9000:2015 [5], 3.2.3]
Note 1 to entry: Requirements for quality management systems are given in EN ISO 9001 [1].
3.5
quality plan
document setting out the specific quality practices, resources and sequence of activities relevant to a
particular product or range of products
3.6
type testing
TT
testing performed to prove that the formulation, product, joint or assembly is capable of conforming to
the requirements given in the relevant standard
Note 1 to entry: The type test results remain valid until there is a change in the material or product or assembly
provided that the process verification tests are done regularly.
3.7
batch release test
BRT
test performed by or on behalf of the manufacturer on a batch of materials or products, which needs to
be satisfactorily completed before the batch can be released
3.8
process verification test
PVT
test performed by, or on behalf of the manufacturer on materials, products or joints or assemblies at
specific intervals to confirm that the process continues to be capable of producing products which
conform to the requirements given in the relevant standard
Note 1 to entry: Such tests are not required to release batches of materials or products; rather they are carried
out as a measure of process control.
3.9
audit test
AT
test performed by a test laboratory on behalf of an inspection body or certification body to confirm that
the material, product, joint or assembly continues to conform to the requirements given in the relevant
standard and to provide i
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.