EN 1453-1:2017
(Main)Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes and the system
Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes and the system
This part of EN 1453 specifies the requirements for structured-wall unplasticized poly(vinyl chloride) (PVC U) pipes and the system intended to be used for soil and waste discharge applications (low and high temperature) inside buildings (application area code "B")
NOTE 1 The intended use is reflected in the marking of products by "B".
This part of EN 1453 is also applicable to structured-wall unplasticized poly(vinyl chloride) (PVC U) pipes, and the system intended for the following purposes:
ventilating part of the pipework in association with discharge applications;
rainwater pipework inside building.
It also specifies the test parameters for the test methods referred to in this standard.
NOTE 2 Single layer foamed PVC U pipes and spirally-formed PVC U pipes are not covered by this standard.
This standard covers a range of nominal sizes and gives recommendations concerning colours.
NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
For external above ground application additional requirements depending on the climatic conditions should be agreed between the manufacturer and the user.
NOTE 4 Pipes conforming to this standard are normally associated with fittings conforming to EN 1329 1. Pipes, fittings and components conforming to any of the product standards listed in Annex C can also be used with pipes conforming to this standard, provided they conform to the requirements for joint dimensions given in Clause 6 and to the requirements in Table 11.
NOTE 5 Joints and adhesives are considered to be part of the system as covered in the scope.
NOTE 6 Products conforming to this standard may be submitted to national requirements on fire regulation.
Kunststoff-Rohrleitungssysteme mit Rohren mit profilierter Wandung zum Ableiten von Abwasser (niedriger und hoher Temperatur) innerhalb von Gebäuden - Weichmacherfreies Polyvinylchlorid (PVC-U) - Teil 1: Anforderungen an Rohre und das Rohrleitungssystem
Systèmes de canalisations en plastique avec des tubes à paroi structurée pour l'évacuation des eaux-vannes et des eaux usées (à basse et à haute température) à l'intérieur des bâtiments - Poly(chlorure de vinyle) non plastifié (PVC-U) - Partie 1 : Spécifications pour tubes et le système
La présente partie de l’EN 1453 spécifie les exigences pour les tubes à paroi structurée fabriqués à partir de poly(chlorure de vinyle) non plastifié (PVC U) et le système destinés à être utilisés pour l'évacuation des eaux-vannes et des eaux usées (à basse et à haute température) à l'intérieur des bâtiments (code de zone d’application « B »).
NOTE 1 L’utilisation prévue est repérée au niveau du marquage des produits par « B ».
La présente partie de l’EN 1453 s’applique également aux tubes à paroi structurée fabriqués à partir de poly(chlorure de vinyle) non plastifié (PVC U) et le système destinés aux usages suivants :
- élément de ventilation des canalisations associées à des applications d’évacuation
- canalisations pour les eaux pluviales à l'intérieur du bâtiment.
Elle couvre également les paramètres d’essais pour les méthodes d’essai dont il est fait référence dans la présente norme.
NOTE 2 Les tubes en PVC U expansé simple couche et les tubes spiralés en PVC U ne sont pas couverts par la présente norme.
La présente norme couvre une gamme de dimensions nominales et donne des recommandations concernant les couleurs.
NOTE 3 Il est de la responsabilité de l'acheteur ou du prescripteur de faire les sélections appropriées à partir de ces données en tenant compte des exigences particulières et des éventuelles règles nationales et des pratiques ou codes de pose appropriés.
Pour une application externe en aérien il convient que soit spécifié entre le fabricant et l'utilisateur des exigences supplémentaires dépendant des conditions climatiques.
NOTE 4 Les tubes conformes à la présente norme sont normalement utilisés avec des raccords conformes à l'EN 1329-1 [1]. Les tubes, raccords et composants conformes à l’une des normes produits listées dans l’Annexe C peuvent également être utilisés avec des tubes conformes à la présente norme sous réserve qu'ils répondent aux exigences dimensionnelles des assemblages données à l’Article 6 et aux exigences du Tableau 11.
NOTE 5 Les assemblages et colles sont considérés comme faisant partie du système tel que couvert dans le domaine d’application.
NOTE 6 Les produits conformes à la présente norme peuvent être soumis à des exigences nationales concernant la réglementation au feu.
Cevni sistemi iz polimernih materialov s strukturirano steno cevi za nizko- in visokotemperaturne odvodne sisteme v stavbah - Nemehčan polivinilklorid (PVC-U) - 1. del: Specifikacije za cevi in sistem
Ta del standarda EN 1453 določa zahteve za strukturirane stene cevi iz nemehčanega polivinilklorida (PVC-U) in sistem, ki je namenjen za odvodne sisteme (nizko- in visokotemperaturne) v zgradbah (koda območja uporabe »B«). Ta del standarda EN 1453 se uporablja tudi za strukturirane stene cevi iz nemehčanega polivinilklorida (PVC-U) in sistem, ki je namenjen: –prezračevalnemu delu cevovoda v povezavi z odvajanjem ⎯cevovodu za deževnico v stavbi. Določa tudi preskusne parametre za preskusne metode, navedene v tem standardu. Ta standard zajema vrsto nazivnih velikosti in podaja priporočila glede barv. Za zunanjo nadzemno uporabo je priporočljiv dogovor med proizvajalcem in uporabnikom glede dodatnih zahtev v povezavi s podnebjem.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunststoff-Rohrleitungssysteme mit Rohren mit profilierter Wandung und glatten Rohroberflächen zum Ableiten von Abwasser (niedriger und hoher Temperatur) innerhalb von Gebäuden - Weichmacherfreies Polyvinylchlorid (PVC-U) - Teil 1: Anforderungen an Rohre und das RohrleitungssystemSystèmes de canalisations en plastique avec des tubes à paroi structurée pour l'évacuation des eaux-vannes et des eaux usées (à basse et à haute température) à l'intérieur des bâtiments - Poly(chlorure de vinyle) non plastifié (PVC-U) - Partie 1 : Spécifications pour tubes et le systèmePlastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes and the system91.140.80Drenažni sistemiDrainage systems23.040.01Deli cevovodov in cevovodi na splošnoPipeline components and pipelines in generalICS:Ta slovenski standard je istoveten z:EN 1453-1:2017SIST EN 1453-1:2017en,fr,de01-marec-2017SIST EN 1453-1:2017SLOVENSKI
STANDARDSIST EN 1453-1:20001DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1453-1
January
t r s y ICS
t uä r v rä r sâ
t uä r v rä r wâ
{ sä s v rä z r Supersedes EN
s v w uæ sã t r r rEnglish Version
Plastics piping systems with structuredæwall pipes for soil Part
sã Specifications for pipes and the system Systèmes de canalisations en plastique avec des tubes àparoi structurée pour l 5évacuation des eauxævannes et et le système
KunststoffæRohrleitungssysteme mit Rohren mit profilierter Wandung zum Ableiten von Abwasser Rohrleitungssystem This European Standard was approved by CEN on
t { October
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s v w uæ sã t r s y ESIST EN 1453-1:2017
Contents Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions, symbols and abbreviations . 6 3.1 Terms and definitions . 6 3.2 Symbols . 8 3.3 Abbreviations . 9 4 Material . 9 4.1 Raw material . 9 4.2 Utilization of non-virgin material . 9 4.3 Sealing ring retaining means . 9 5 General characteristics . 10 5.1 Appearance . 10 5.2 Colour . 10 6 Geometrical characteristics . 10 6.1 General . 10 6.2 Dimensions of pipes . 10 6.3 Dimensions of sockets . 13 7 Mechanical characteristics . 19 7.1 General requirements . 19 7.2 Additional requirements . 20 8 Physical characteristics . 21 9 Performance requirements . 22 10 Sealing rings . 22 11 Adhesives . 22 12 Marking . 22 12.1 General . 22 12.2 Minimum required marking . 23 12.3 Additional marking . 23 Annex A (informative)
Guidance for calcium carbonate additives . 24 A.1 Composition of calcium carbonate additives . 24 A.2 Physical properties of calcium carbonate additive . 24 Annex B (normative)
Utilization of non-virgin material . 25 B.1 Own reprocessed material . 25 B.2 External reprocessed and recycled materials with agreed specification . 25 B.3 External reprocessed and recycled material not covered by an agreed specification . 28 Annex C (informative)
Product standards . 29 Bibliography . 30 SIST EN 1453-1:2017
1) EN 1453 does not cover a recommended practice for installation. A recommended practice for installation is covered by the following European Technical Report: CEN/TR 13801, Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure — Thermoplastics — Recommended practice for installation. SIST EN 1453-1:2017
1 Scope This part of EN 1453 specifies the requirements for structured-wall unplasticized poly(vinyl chloride) (PVC-U) pipes and the system intended to be used for soil and waste discharge applications (low and high temperature) inside buildings (application area code “B”) NOTE 1 The intended use is reflected in the marking of products by “B”. This part of EN 1453 is also applicable to structured-wall unplasticized poly(vinyl chloride) (PVC-U) pipes, and the system intended for the following purposes: — ventilating part of the pipework in association with discharge applications; — rainwater pipework inside building. It also specifies the test parameters for the test methods referred to in this standard. NOTE 2 Single layer foamed PVC-U pipes and spirally-formed PVC-U pipes are not covered by this standard. This standard covers a range of nominal sizes and gives recommendations concerning colours. NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. For external above ground application additional requirements depending on the climatic conditions should be agreed between the manufacturer and the user. NOTE 4 Pipes conforming to this standard are normally associated with fittings conforming to EN 1329–1 [1]. Pipes, fittings and components conforming to any of the product standards listed in Annex C can also be used with pipes conforming to this standard, provided they conform to the requirements for joint dimensions given in Clause 6 and to the requirements in Table 11. NOTE 5 Joints and adhesives are considered to be part of the system as covered in the scope. NOTE 6 Products conforming to this standard may be submitted to national requirements on fire regulation. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 681-1, Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber EN 681-2, Elastomeric Seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers EN 1905, Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes, fittings and material - Method for assessment of the PVC content based on total chlorine content EN 10204:2004, Metallic products - Types of inspection documents EN 14680, Adhesives for non-pressure thermoplastics piping systems - Specifications EN 15346:2014, Plastics - Recycled plastics - Characterization of poly(vinyl chloride) (PVC) recyclates SIST EN 1453-1:2017
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.