EN 16228-5:2014+A1:2021
(Main)Drilling and foundation equipment - Safety - Part 5: Diaphragm walling equipment
Drilling and foundation equipment - Safety - Part 5: Diaphragm walling equipment
This European Standard, together with part 1, deals with all significant hazards for diaphragm walling equipment when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer associated with the whole life time of the machine (see Clause 4).
The requirements of this part are complementary to the common requirements formulated in EN 16228-1:2014+A1:2021.
This document does not repeat the requirements from EN 16228-1:2014+A1:2021, but adds or replaces the requirements for application for diaphragm walling equipment.
Geräte für Bohr- und Gründungsarbeiten - Sicherheit - Teil 5: Geräte für Schlitzwandarbeiten
Diese Europäische Norm behandelt zusammen mit Teil 1 alle signifikanten Gefährdungen für Geräte für Schlitzwandarbeiten, wenn sie bestimmungsgemäß und unter den Bedingungen der Fehlanwendung, die vernünftigerweise vom Hersteller vorhersehbar sind und mit der gesamten Lebensdauer der Maschine in Verbindung stehen, verwendet werden (siehe Abschnitt 4).
Die Anforderungen in diesem Teil gelten zusätzlich zu den in !EN 16228 1:2014+A1:2021" gestellten Anforderungen.
Das vorliegende Dokument wiederholt nicht die Anforderungen von !EN 16228 1:2014+A1:2021", sondern ergänzt oder ersetzt die Anforderungen für die Anwendung von Geräten für Schlitzwandarbeiten.
Machines de forage et de fondation - Sécurité - Partie 5 : Machines pour parois moulées
La présente Norme européenne traite, avec la partie 1, de tous les phénomènes dangereux significatifs liés aux machines pour parois moulées, lorsqu'elles sont utilisées normalement et dans les conditions de mauvaise utilisation raisonnablement prévisibles par le fabricant, associés à toute la durée de vie des machines (voir Article 4).
Les prescriptions figurant dans la présente partie viennent en complément des prescriptions communes spécifiées dans l'EN 16228-1:2014+A1:2021.
Le présent document ne répète pas les prescriptions de l'EN 16228-1:2014+A1:2021, mais ajoute ou remplace les prescriptions applicables aux machines pour parois moulées.
Oprema za vrtanje in temeljenje - Varnost - 5. del: Oprema za izdelavo membranskih sten (vključno z dopolnilom A1)
Ta evropski standard skupaj s 1. delom obravnava vsa večja tveganja za opremo za izdelavo membranskih sten, če se uporablja, kot je bilo predvideno, in pod pogoji nepravilne uporabe, ki jih je razumno predvidel proizvajalec, v zvezi s celotno življenjsko dobo opreme (glej točko 4).
Zahteve iz tega dela dopolnjujejo splošne zahteve, navedene v standardu EN 16228-1:2014+A1:2021.
Ta dokument ne ponavlja zahtev iz standarda EN 16228-1:2014+A1:2021, temveč dodaja ali nadomešča zahteve za uporabo opreme za izdelavo membranskih sten.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2022
Oprema za vrtanje in temeljenje - Varnost - 5. del: Oprema za izdelavo
membranskih sten (vključno z dopolnilom A1)
Drilling and foundation equipment - Safety - Part 5: Diaphragm walling equipment
Geräte für Bohr- und Gründungsarbeiten - Sicherheit - Teil 5: Geräte für
Schlitzwandarbeiten
Machines de forage et de fondation - Sécurité - Partie 5 : Machines pour parois moulées
Ta slovenski standard je istoveten z: EN 16228-5:2014+A1:2021
ICS:
53.100 Stroji za zemeljska dela Earth-moving machinery
93.020 Zemeljska dela. Izkopavanja. Earthworks. Excavations.
Gradnja temeljev. Dela pod Foundation construction.
zemljo Underground works
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 16228-5:2014+A1
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2021
EUROPÄISCHE NORM
ICS 93.020 Supersedes EN 16228-5:2014
English Version
Drilling and foundation equipment - Safety - Part 5:
Diaphragm walling equipment
Machines de forage et de fondation - Sécurité - Partie 5: Geräte für Bohr- und Gründungsarbeiten - Sicherheit -
Machines pour parois moulées Teil 5: Geräte für Schlitzwandarbeiten
This European Standard was approved by CEN on 6 March 2014 and includes Amendment 1 approved by CEN on 22 November
2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 16228-5:2014+A1:2021 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 List of additional significant hazards . 8
5 Safety requirements and/or protective measures . 9
5.1 General . 9
5.2 Requirements for strength and stability . 9
5.2.1 General . 9
5.2.2 Loads from diaphragm wall cutting tools . 9
5.2.3 Stability of diaphragm walling rig . 9
5.3 Winches and pulleys . 11
5.4 Control devices . 11
5.4.1 General . 11
5.4.2 Control of the diaphragm walling rig equipped with cutter . 11
5.4.3 Control of winches for suspending grabs or cutters when changing ropes . 12
5.4.4 !Free fall operation" . 12
5.5 Moving parts involved in the process . 14
5.6 Maintenance of diaphragm wall cutters . 14
5.7 Hose and cable handling systems . 14
5.8 !Holding brake" . 14
5.9 !Compatibility of the carrier machine" . 14
5.10 Inclination of the carrier . 14
5.11 !Operating position(s)" . 14
5.12 !Noise" . 15
6 Verification of the safety requirements and/or protective measures . 15
6.1 General . 15
7 Information for use . 17
7.1 Operator’s manual . 17
7.1.1 General . 17
7.1.2 Specific instructions on the diaphragm wall cutting tools put on the market
separetely . 17
7.2 Maintenance instructions . 18
Annex A (normative) Noise test code . 19
Annex ZA (informative) !Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered" . 20
Bibliography . 24
European foreword
This document (EN 16228-5:2014+A1:2021) has been prepared by Technical Committee CEN/TC 151
“Construction equipment and building material machines - Safety”, the secretariat of which is held by
DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2022 and conflicting national standards shall be
withdrawn at the latest by June 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes !EN 16228-5:2014".
This document includes Amendment 1 approved by CEN on 22 November 2021.
The start and finish of text introduced or altered by amendment is indicated in the text by tags !".
This document has been prepared under a Standardization Request given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of EU
Directive(s) / Regulation(s).
For relationship with EU Directive(s) / Regulation(s), see informative Annex ZA, which is an integral
part of this document.
This European Standard is divided into several parts and covers drilling and foundation equipment.
Part 1 contains requirements that are/may be common to all drilling and foundation equipment. Other
parts contain additional requirements for specific machines that supplement or modify the
requirements of part 1. Compliance with the clauses of part 1 together with those of a relevant specific
part of this standard giving requirements for a particular machine provides one means of conforming
with the essential health and safety requirements of the Directive concerned.
When a relevant specific part does not exist, part 1 can help to establish the requirements for the
machine, but will not by itself provide a means of conforming to the relevant essential health and safety
requirements of the Directive.
This European Standard, EN 16228, Drillling and foundation equipment – Safety, consists of the
following parts:
Part 1: Common requirements
!Part 2: Mobile drill rigs for civil and geotechnical engineering in soil or soil and rock mixture"
Part 3: Horizontal directional drilling equipment (HDD)
Part 4: Foundation equipment
Part 5: Diaphragm walling equipment
Part 6: Jetting, grouting and injection equipment
Part 7: Interchangeable auxiliary equipment
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Introduction
This European Standard is a type C standard as stated in EN ISO 12100.
The machinery concerned and the extent to which hazards are covered are indicated in the scope of this
standard.
When provisions of this type C standard are different from those which are stated in type A or B
standards, the provisions of this type C standard take precedence over the provisions of the other
standards, for drilling and foundation equipment that have been designed and built according to the
provisions of this type C standard.
1 Scope
This European Standard, together with part 1, deals with all significant hazards for diaphragm walling
equipment when they are used as intended and under the conditions of misuse which are reasonably
foreseeable by the manufacturer associated with the whole life time of the machine (see Clause 4).
The requirements of this part are complementary to the common requirements formulated in
!EN 16228-1:2014+A1:2021".
This document does not repeat the requirements from !EN 16228-1:2014+A1:2021", but adds or
replaces the requirements for application for diaphragm walling equipment.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
EN 474-5:2006+A3:2013, Earth-moving machinery — Safety — Part 5: Requirements for hydraulic
excavators
EN 474-12:2006+A1:2008, Earth-moving machinery — Safety — Part 12: Requirements for cable
excavators
!EN 16228-1:2014+A1:2021", Drilling and foundation equipment — Safety — Part 1: Common
requirements
!EN 16228-4:2014+A1:2021, Drilling and foundation equipment — Safety — Part 4: Foundation
equipment
EN 13000:2010+A1:2014, Cranes — Mobile cranes"
EN ISO 12100:2010, Safety of machinery — General principles for design — Risk assessment and risk
reduction (ISO 12100:2010)
ISO 6395:2008, Earth-moving machinery — Determination of sound power level — Dynamic test
conditions
ISO 6396:2008, Earth-moving machinery — Determination of emission sound pressure level at operator’s
position — Dynamic test conditions
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN ISO 12100:2010,
!EN 16228-1:2014+A1:2021" and the fo
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.