Railway applications - Wheelsets and bogies - Monobloc wheels - Technical approval procedure - Part 1: Forged and rolled wheels

The aim of this European Standard is to define the requirements that a monobloc wheel of a freight of passenger railway vehicle non-powered axle shall meet in order to be able to be used on a European network.
For wheels of powered axles or wheels with noise dampers, the requirements may be amended or supplemented.
For light vehicles and tramways, other standards or documents accepted by the customer and supplier may be used.
This European Standard only applies to wheels of new design.
These requirements are intended to assess the validity of the design choice for the proposed use.
The assessment of these requirements is the technical approval procedure.
This European Standard is applicable to forged and rolled wheels for which the quality requirements are defined in EN 13262.

Bahnanwendungen - Radsätze und Drehgestelle - Vollräder - Technische Zulassungsverfahren - Teil 1: Geschmiedete und gewalzte Räder

Applications ferroviaires - Essieux montés et bogies - Roues monobloc - Procédure d'homologation technique - Partie 1: Roues forgées et laminées

Železniške naprave - Kolesne dvojice in podstavni vozički - Monoblok kolesa - Postopek za tehnično odobritev - 1. del: Kovana in valjana kolesa

General Information

Status
Not Published
Current Stage
5060 - Closure of Vote - Formal Approval
Start Date
23-Dec-2010
Due Date
24-Dec-2011
Completion Date
23-Dec-2010

Relations

Buy Standard

Amendment
EN 13979-1:2004/kprA2:2010
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 13979-1:2004/kprA2:2010
01-december-2010
äHOH]QLãNHQDSUDYH.ROHVQHGYRMLFHLQSRGVWDYQLYR]LþNL0RQREORNNROHVD
3RVWRSHN]DWHKQLþQRRGREULWHYGHO.RYDQDLQYDOMDQDNROHVD

Railway applications - Wheelsets and bogies - Monobloc wheels - Technical approval

procedure - Part 1: Forged and rolled wheels
Bahnanwendungen - Radsätze und Drehgestelle - Vollräder - Technische
Zulassungsverfahren - Teil 1: Geschmiedete und gewalzte Räder

Applications ferroviaires - Essieux montés et bogies - Roues monobloc - Procédure

d'homologation technique - Partie 1: Roues forgées et laminées
Ta slovenski standard je istoveten z: EN 13979-1:2003/FprA2
ICS:
45.040 Materiali in deli za železniško Materials and components
tehniko for railway engineering
SIST EN 13979-1:2004/kprA2:2010 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 13979-1:2004/kprA2:2010
---------------------- Page: 2 ----------------------
SIST EN 13979-1:2004/kprA2:2010
EUROPEAN STANDARD
FINAL DRAFT
EN 13979-1:2003+A1:2009
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA2
September 2010
ICS 45.040; 45.060.01
English Version
Railway applications - Wheelsets and bogies - Monobloc wheels
- Technical approval procedure - Part 1: Forged and rolled
wheels

Applications ferroviaires - Essieux montés et bogies - Bahnanwendungen - Radsätze und Drehgestelle - Vollräder

Roues monobloc - Procédure d'homologation technique - - Technische Zulassungsverfahren - Teil 1: Geschmiedete

Partie 1: Roues forgées et laminées und gewalzte Räder

This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee

CEN/TC 256.

This draft amendment A2, if approved, will modify the European Standard EN 13979-1:2003+A1:2009. If this draft becomes an

amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion

of this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made

by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same

status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,

Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and

shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13979-1:2003/FprA2:2010: E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13979-1:2004/kprA2:2010
EN 13979-1:2003/prA2:2010 (E)
Contents Page

Foreword..............................................................................................................................................................3

1 Amendment of the foreword.................................................................................................................4

2 Amendment of Annex ZA......................................................................................................................4

---------------------- Page: 4 ----------------------
SIST EN 13979-1:2004/kprA2:2010
EN 13979-1:2003/prA2:2010 (E)
Foreword

This document (EN 13979-1:2003/FprA2:2010) has been prepared by Technical Committee CEN/TC 256

“Railway applications”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.

This document has been prepared under a mandate given to CEN/CENELEC/ETSI by the European

Commission and the European Free Trade Association, and supports essential requirements of

EU Directive 2008/57/EC.

For relationship with EU Directive 2008/57/EC, see informative Annex ZA, which is an integral part of this

document.
---------------------- Page: 5 ----------------------
SIST EN 13979-1:2004/kprA2:2010
EN 13979-1:2003/prA2:2010 (E)
1 Amendment of the foreword
Replace the 11 paragraph of the Foreword with:

"This document has been prepared under a mandate given to CEN/CENELEC/ETSI by the European

Commission and the European Free Trade Association, and supports essential requirements of EU Directive

2008/57/EC."
Replace the 12 paragraph of the Foreword with:

"For relationship with EU Directive 2008/57/EC, see informative Annex ZA, which is an integral part of this

document."
2 Amendment of Annex ZA
Replace Annex ZA with the following Annex ZA:
Annex ZA
(informative)
Relationship between this European Standard and the Essential Requirements of
EU Directive 2008/57/EC
This European Standard has been prepared und
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.