iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 13702-1:2003

(Main)

Bitumen and bituminous binders - Determination of dynamic viscosity of modified bitumen - Part 1: Cone and plate method

Bitumen and bituminous binders - Determination of dynamic viscosity of modified bitumen - Part 1: Cone and plate method

This European Standard specifies a method for determining the dynamic viscosity of a bituminous binder over a range of temperatures by means of a cone and plateviscosimeter. NOTE:Unlike penetration grade bitumen, polymer modified bitumens (PmB) do not show a straight line on the Heukelom-Diagram. This implies that in order to obtain information about the temperature susceptibility of PmB's, viscosity should be measured at different temperatures.

Bitumen und bitumenhaltige Bindemittel - Bestimmung der dynamischen Viskosität von modifizierten Bitumen - Teil 1: Platte-Kegel-Verfahren

Diese Europäische Norm legt ein Verfahren zur Bestimmung der dynamischen Viskosität eines bitumenhaltigen Bindemittels mit einem Platte-Kegel- Viskosimeter über einen Temperaturbereich fest. ANMERKUNG: Anders als Penetrationsbitumen weist polymermodifiziertes Bitumen (PmB) keine gerade Linie im Heukelom-Diagramm auf. Das bedeutet, daß die Viskosität, um Angaben über die Temperaturabhängigkeit von PmB zu erhalten, bei verschiedenen Temperaturen gemessen werden sollte.

Bitumes et liants bitumineux - Détermination de la viscosité dynamique des bitumes modifiés - Partie 1: Méthode cône et plateau

La présente Norme européenne prescrit une méthode permettant de déterminer la viscosité dynamique d'un liant bitumineux modifié sur un intervalle de température, au moyen d'un viscosimètre à cône et plateau. Bien que la méthode ait été développée pour les liants modifiés, elle est également applicable pour d'autres liants bitumineux.
NOTE   Contrairement aux bitumes purs, les bitumes modifiés par des polymères (BMP) peuvent ne pas décrire une ligne droite sur le diagramme de Heukelom. En conséquence, pour obtenir des informations sur la susceptibilité à la température des BMP, il est recommandé de mesurer leur viscosité à différentes températures.
AVERTISSEMENT - L'utilisation de la présente Norme européenne implique l'intervention de produits, d'opérations et d'équipements à caractère dangereux. La présente Norme européenne n'est pas censée aborder tous les problèmes de sécurité concernés par son usage. Il est de la responsabilité de l'utilisateur de consulter et d'établir des règles de sécurité et d'hygiène appropriées et de déterminer l'applicabilité des restrictions réglementaires avant utilisation.

Bitumen in bitumenska veziva – Določevanje dinamične viskoznosti modificiranih bitumnov – 1. del: Metoda s konusom in ploščo

General Information

Status
Withdrawn
Publication Date
16-Dec-2003
Withdrawal Date
25-May-2010
ICS
91.100.50 - Binders. Sealing materials
Technical Committee
CEN/TC 336 - Bituminous binders
Drafting Committee
CEN/TC 336/WG 4 - Modified bitumens
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
26-May-2010
Completion Date
26-May-2010
Ref Project
SIST EN 13702-1:2004 - Bitumen and bituminous binders - Determination of dynamic viscosity of modified bitumen - Part 1: Cone and plate method

Relations

Replaced By
EN 13702:2010 - Bitumen and bituminous binders - Determination of dynamic viscosity of modified bitumen by cone and plate method
Effective Date
22-Dec-2008

Buy Standard

EN 13702-1:2004EN 13702-1:2004
PreviousNext
Standard
EN 13702-1:2004
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.PRGLILFLUDQLKBitumen und bitumenhaltige Bindemittel - Bestimmung der dynamischen Viskosität von modifizierten Bitumen - Teil 1: Platte-Kegel-VerfahrenBitumes et liants bitumineux - Détermination de la viscosité dynamique des bitumes modifiés - Partie 1: Méthode cône et plateauBitumen and bituminous binders - Determination of dynamic viscosity of modified bitumen - Part 1: Cone and plate method91.100.50Veziva. Tesnilni materialiBinders. Sealing materials75.140Voski, bitumni in drugi naftni proizvodiWaxes, bituminous materials and other petroleum productsICS:Ta slovenski standard je istoveten z:EN 13702-1:2003SIST EN 13702-1:2004en01-september-2004SIST EN 13702-1:2004SLOVENSKI
STANDARD



SIST EN 13702-1:2004



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13702-1December 2003ICS 91.100.50English versionBitumen and bituminous binders - Determination of dynamicviscosity of modified bitumen - Part 1: Cone and plate methodBitumes et liants bitumineux - Détermination de la viscositédynamique des bitumes modifiés - Partie 1: Méthode côneet plateauBitumen und bitumenhaltige Bindemittel - Bestimmung derdynamischen Viskosität von modifizierten Bitumen - Teil 1:Platte-Kegel-VerfahrenThis European Standard was approved by CEN on 21 November 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13702-1:2003 ESIST EN 13702-1:2004



EN 13702-1:2003 (E)2Contents pageForeword.31Scope.42Normative references.43Principle.44Apparatus.55Sampling.56Procedure.57Expression of results.68Precision.68.1Repeatability.68.2Reproducibility.69Test report.6SIST EN 13702-1:2004



EN 13702-1:2003 (E)3ForewordThis document EN 13702-1:2003 has been prepared by Technical Committee CEN/TC 336 “Bituminous binders”,the secretariat of which is held by AFNOR.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by June 2004, and conflicting national standards shall be withdrawn at the latest byJune 2004.This European Standard consists of the following parts under the general title Bitumen and bituminous binders –Determination of dynamic viscosity of modified bitumen.Part 1 – Cone and plate methodPart 2 – Coaxial cylinders methodAccording to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard : Austria, Belgium, Czech Republic, Denmark, Finland,France,
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 12595:2023(Main)
Bitumen and bituminous binders - Determination of kinematic viscosity
klSIST FprEN 12595:2023

This document specifies a method for the determination of the kinematic viscosity of bituminous binders at 60 °C and 135 °C, in a range from 6 mm2/s to 300 000 mm2/s. Other temperatures are possible if calibration constants are known. Bituminous emulsions are not covered within the scope of this method.
Results for this method can be used to calculate dynamic viscosity when the density of the test material is known or can be determined.
NOTE   This document assumes Newtonian behaviour of the sample at test conditions.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to identify the hazards and assess the risks involved in performing this test method and to implement sufficient control measures to protect individual operators (and the environment). This includes appropriate safety and health practices and determination of the applicability of regulatory limitations prior to use.

  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14769:2023(Main)
Bitumen and bituminous binders - Accelerated long-term ageing conditioning by a Pressure Ageing Vessel (PAV)
kSIST FprEN 14769:2023

This document specifies an accelerated long-term ageing/conditioning procedure for bituminous binders. The procedure involves ageing trays of binder at elevated temperatures under pressurized conditions in a pressure ageing vessel (PAV).
NOTE   For binders to be used in hot and warm asphalt applications, the pre-conditioning of the sample can be performed using one of the methods in the EN 12607 series. For binders to be used in bituminous emulsion and cut back or fluxed applications, the stabilization of the sample is such that there are no volatiles remaining.
WARNING - The use of this document can involve hazardous materials, operations and equipment, in particular, the use of a high pressure ageing vessel. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate health and safety practices and determine the applicability of regulatory limitations prior to use. If there is the likelihood of volatile components being present in a binder, this procedure is not used.

  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14770:2023(Main)
Bitumen and bituminous binders - Determination of complex shear modulus and phase angle - Dynamic Shear Rheometer (DSR)
kSIST FprEN 14770:2023

This document specifies a general method of using a dynamic shear rheometer (DSR) for measuring the rheological properties of bituminous binders. The procedure involves determining the complex shear modulus and phase angle of binders over a range of test frequencies and test temperatures when tested in oscillatory shear.
From the test, the complex shear modulus, |G*|, and its phase angle, δ, at a given temperature and frequency are calculated, as well as the components G' and G" of the complex shear modulus.
This method is applicable to un-aged, aged, stabilized and recovered bituminous binders. The test procedure in accordance with this document is not applicable for bituminous binders with particles larger than 250 μm (e.g. filler material, granulated rubber).
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12596:2023(Main)
Bitumen and bituminous binders - Determination of dynamic viscosity by vacuum capillary
kSIST FprEN 12596:2023

This document specifies a method for the determination of the dynamic viscosity of bituminous binders by means of a vacuum capillary viscometer at 60 °C in a range between 0,003 6 Pa⋅s and 580 000 Pa⋅s. Other temperatures are possible if calibration constants are known. Bituminous emulsions and non-newtonian binders (e.g. some polymer modified bitumen) are not within the scope of this method.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to identify the hazards and assess the risks involved in performing this test method and to implement sufficient control measures to protect individual operators (and the environment). This includes appropriate safety and health practices and determination of the applicability of regulatory limitations prior to use.

  • Draft
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14771:2023(Main)
Bitumen and bituminous binders - Determination of the flexural creep stiffness - Bending Beam Rheometer (BBR)
kSIST FprEN 14771:2023

This document specifies a method for the determination of the flexural creep stiffness of bitumen and bituminous binders in the range of 30 MPa to 1 GPa by means of the bending beam rheometer.
The method can be applied to a variety of bitumens, including unmodified as well as modified binders, as fresh (unused) binders, as well as binders after laboratory ageing conditioning (e.g. EN 12607-1, EN 14769), and also binders that have been recovered from asphalt mixtures.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12846-1:2022(Main)
Bitumen and bituminous binders - Determination of efflux time by the efflux viscometer - Part 1: Bituminous emulsions
SIST EN 12846-1:2023

This document specifies a method for the determination of the efflux time at 40 °C of bituminous emulsions in seconds using an efflux viscometer. Alternative test temperature is 50 °C.
NOTE   The procedure described in this document can also be followed to determine efflux time at other temperatures such as 25 °C.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12846-2:2022(Main)
Bitumen and bituminous binders - Determination of efflux time by the efflux viscometer - Part 2: Cut-back and fluxed bituminous binders
SIST EN 12846-2:2023

This document specifies a method for the determination of the efflux time at 25 °C of petroleum cut-back and fluxed bituminous binders in seconds using an efflux viscometer. Alternative test temperatures are 40 °C, 50 °C and 60 °C.
WARNING - The use of this document involves hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17643:2022(Main)
Bitumen and bituminous binders - Determination of equi-shear modulus temperature and phase angle using a Dynamic Shear Rheometer (DSR) - BTSV test
SIST EN 17643:2022

This document specifies the Binder Fast Characterization Test (for short: BTSV test, German: Bitumen-Typisierungs-Schnell-Verfahren). The test is conducted using a Dynamic Shear Rheometer (DSR). It is used to characterize bitumen and bituminous binders and to assess the deformation behaviour at high service temperatures.
The test procedure described in this document covers the testing of paving grade bitumen or modified bitumen, as fresh (unused) binders, as well as binders after laboratory ageing conditioning (e.g. EN 12607-1, EN 14769), and also binders that have been recovered from asphalt mixtures. The test procedure in accordance with this document is not applicable for bituminous binders with particles larger than 250 μm (e.g. filler material, granulated rubber).
NOTE   The test procedure has not been applied on bituminous binders recovered from bitumen emulsions yet.
The test determines the temperature and the associated phase angle at which a bituminous binder exhibits a defined complex shear modulus in stress-controlled oscillation mode at constant frequency and with continuous increase of the test temperature.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to ensure that regulatory requirements are fulfilled prior to application of this document. This document involves handling of apparatus and binders at very high temperatures. Always wear protective gloves and eyewear when handling hot binders, and avoid contact with any exposed, unprotected skin.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12847:2022(Main)
Bitumen and bituminous binders - Determination of settling tendency of bituminous emulsions
SIST EN 12847:2022

This document specifies a method for the determination of the settling tendency of bituminous emulsions.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12850:2022(Main)
Bitumen and bituminous binders - Determination of the pH value of bituminous emulsions
SIST EN 12850:2022

This document specifies a method for measuring the pH value of bituminous emulsions.
It is applicable to anionic, cationic bituminous emulsions and bituminous emulsions prepared by means of non-ionic surfactant.
NOTE   In certain circumstances, the pH value can provide an indication of the ionic character of a bituminous emulsion when confirmed by a particle polarity test conforming to EN 1430 [1].
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day