EN ISO 10673:1998
(Main)Plain washers for screw and washer assemblies - Small, normal and large series - Product grade A (ISO 10673:1998)
Plain washers for screw and washer assemblies - Small, normal and large series - Product grade A (ISO 10673:1998)
Flache Scheiben für Kombi-Schrauben - Kleine, normale und große Reihe - Produktklasse A (ISO 10673:1998)
Diese Internationale Norm legt die Eigenschaften von flachen Scheiben aus Stahl der kleinen, normalen und großen Reihe, in Produktklasse A, mit den Härte- klassen 200 HV und 300 HV für Kombi-Schrauben nach ISO 10644 fest.
Rondelles plates pour vis à rondelle plate incorporée - Séries étroite, normale et large - Grade A (ISO 10673:1998)
Okrogle ravne podložke za vijake z ujeto podložko majhnih in normalnih mer, razred izdelave A (ISO 10673:1998)
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Okrogle ravne podložke za vijake z ujeto podložko majhnih in normalnih mer, razred izdelave A (ISO 10673:1998)Flache Scheiben für Kombi-Schrauben - Kleine, normale und große Reihe - Produktklasse A (ISO 10673:1998)Rondelles plates pour vis a rondelle plate incorporée - Séries étroite, normale et large - Grade A (ISO 10673:1998)Plain washers for screw and washer assemblies - Small, normal and large series - Product grade A (ISO 10673:1998)21.060.30Podložke, varovalni elementiWashers, locking elementsICS:Ta slovenski standard je istoveten z:EN ISO 10673:1998SIST EN ISO 10673:2001en01-julij-2001SIST EN ISO 10673:2001SLOVENSKI
STANDARD
AReference numberISO 10673:1998(E)INTERNATIONALSTANDARDISO10673First edition1998-07-01Plain washers for screw and washerassemblies — Small, normal and largeseries — Product grade ARondelles plates pour vis à rondelle plate incorporée — Séries étroite,normale et large — Grade ASIST EN ISO 10673:2001
ISO 10673:1998(E)©
ISO 1998All rights reserved. Unless otherwise specified, no part of this publication may be reproducedor utilized in any form or by any means, electronic or mechanical, including photocopying andmicrofilm, without permission in writing from the publisher.International Organization for StandardizationCase postale 56 · CH-1211 Genève 20 · SwitzerlandInternetiso@iso.chPrinted in SwitzerlandiiForewordISO (the International Organization for Standardization) is a worldwidefederation of national standards bodies (ISO member bodies). The work ofpreparing International Standards is normally carried out through ISOtechnical committees. Each member body interested in a subject for whicha technical committee has been established has the right to be representedon that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collab-orates closely with the International Electrotechnical Commission (IEC) onall matters of electrotechnical standardization.Draft International Standards adopted by the technical committees arecirculated to the member bodies for voting. Publication as an InternationalStandard requires approval by at least 75 % of the member bodies castinga vote.International Standard ISO 10673 was prepared by Technical CommitteeISO/TC 2, Fasteners.Annex A of this International Standard is for information only.SIST EN ISO 10673:2001
INTERNATIONAL STANDARD
© ISOISO 10673:1998(E)1Plain washers for screw and washer assemblies — Small,normal and large series — Product grade A1
ScopeThis International Standard specifies the characteristics of plain steel washers, small, normal and large series, ofproduct grade A with hardness classes 200 HV and 300 HV for metric screw and washer assemblies according toISO 10644.2
Normative referencesThe following standards contain provisions which, through reference in this text, constitute provisions of thisInternational Standard. At the time of publication, the editions indicated were valid. All standards are subject torevision, and parties to agreements based on this International Standard are encouraged to investigate thepossibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintainregisters of currently valid International Standards.ISO 3269:1988, Fasteners — Acceptance inspection.ISO 4042:—1), Fasteners — Electroplated coatings.ISO 4759-3:1991, Tolerances for fasteners — Part 3: Plain washers for bolts, screws and nuts with nominal threaddiameters from 1 mm up to and including 150 mm — Product grades A and C.ISO 6507-1:1997, Metallic materials — Vickers hardness test — Pa
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.