EN 14399-5:2015

High-strength structural bolting assemblies for preloading - Part 5: Plain washers

This European Standard specifies, together with EN 14399 1 and EN 14399 2, hardened and tempered plain washers intended for bolting assemblies with large series hexagon high-strength structural bolts and nuts with threads from M12 to M36 inclusive. Washers according to this standard can be applied under the nut only.
Washers according to this standard are not intended to be used in direct contact with oversized or slotted holes.
NOTE   Attention is drawn to the importance of ensuring that the washers are correctly used if satisfactory results are to be obtained. For recommendations concerning proper application, reference to EN 1090-2 is made.

Hochfeste vorspannbare Garnituren für Schraubverbindungen im Metallbau - Teil 5: Flache Scheiben

Diese Europäische Norm legt, zusammen mit EN 14399-1 und EN 14399-2, Anforderungen für vergütete flache Scheiben, welche für die Ver¬wendung mit hochfesten Sechskantschrauben und  muttern mit großer Schlüsselweite für den Metallbau mit Gewindegrößen von M12 bis M36 vorgesehen sind, fest. Scheiben nach dieser Norm können nur unter der Mutter verwendet werden.
Scheiben nach dieser Norm sind nicht dafür vorgesehen in direktem Kontakt mit übergroßen Löchern oder Langlöchern verwendet zu werden.
ANMERKUNG   Es wird darauf hingewiesen, dass zufriedenstellende Ergebnisse nur dann erzielt werden, wenn sichergestellt ist, dass die Scheiben sachgerecht eingesetzt werden. Für Empfehlungen zur richtigen Anwendung wird auf EN 1090-2 verwiesen.

Boulonnerie de construction métallique à haute résistance apte à la précontrainte - Partie 5 : Rondelles plates

La présente Norme européenne, avec l’EN 14399-1 et l’EN 14399-2, spécifie les exigences applicables aux rondelles plates trempées et revenues destinées à être assemblées avec des vis et écrous hexagonaux de construction métallique à haute résistance à surplat de série large et de diamètre de filetage de M12 à M36 inclus. Les rondelles conformes à la présente norme peuvent uniquement être utilisées sous l'écrou.
Les rondelles conformes à la présente norme ne sont pas destinées à être utilisées en contact direct avec des trous oblongs ou de grande dimension.
NOTE   Il est important de s’assurer que les rondelles soient utilisées de façon correcte afin d’obtenir un résultat satisfaisant. Pour les recommandations relatives à la bonne utilisation, se référer à l’EN 1090-2.

Visokotrdnostne strukturne vijačne zveze za prednapetje - 5. del: Ploščate podložke

Ta dokument skupaj s standardom EN 14399-1 določa ojačane in kaljene ploščate podložke, namenjene za zveze z velikimi vrstami visokotrdnostnih strukturnih vijakov s šestrobo glavo in šestrobimi maticami z navoji od M12 do vključno M36. Podložke po tem standardu se lahko uporabljajo samo pod matico.
OPOMBA: Opozoriti je treba na pomembnost zagotavljanja pravilne uporabe podložk za dosego zadovoljivih rezultatov. Za priporočila glede pravilne uporabe je naveden standard EN 1090-2.

General Information

• Status: Published
• Publication Date: 17-Feb-2015
• Withdrawal Date: 29-Nov-2016
• ICS: 21.060.30 - Washers, locking elements
• Technical Committee: CEN/TC 185 - Threaded and nonthreaded mechanical fasteners and accessories
• Drafting Committee: CEN/TC 185/WG 6 - Structural bolting
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Ref Project: SIST EN 14399-5:2015 - High-strength structural bolting assemblies for preloading - Part 5: Plain washers

Relations

• Replaces: EN 14399-5:2005/AC:2006 - High-strength structural bolting assemblies for preloading - Part 5: Plain washers
• Effective Date: 25-Feb-2015
• Replaces: EN 14399-5:2005 - High-strength structural bolting assemblies for preloading - Part 5: Plain washers
• Effective Date: 19-Mar-2011

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.SRGORåNHHochfeste vorspannbare Garnituren für Schraubverbindungen im Metallbau - Teil 5: Flache ScheibenBoulonnerie de construction métallique à haute résistance apte à la précontrainte - Partie 5: Rondelles platesHigh-strength structural bolting assemblies for preloading - Part 5: Plain washers21.060.30Podložke, varovalni elementiWashers, locking elementsICS:Ta slovenski standard je istoveten z:EN 14399-5:2015SIST EN 14399-5:2015en,fr,de01-maj-2015SIST EN 14399-5:2015SLOVENSKI
STANDARDSIST EN 14399-5:2005/AC:2006SIST EN 14399-5:20051DGRPHãþD



SIST EN 14399-5:2015



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14399-5
February 2015 ICS 21.060.30 Supersedes EN 14399-5:2005English Version
High-strength structural bolting assemblies for preloading - Part 5: Plain washers
Boulonnerie de construction métallique à haute résistance apte à la précontrainte - Partie 5 : Rondelles plates
Hochfeste vorspannbare Garnituren für Schraubverbindungen im Metallbau - Teil 5: Flache Scheiben This European Standard was approved by CEN on 18 October 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14399-5:2015 ESIST EN 14399-5:2015



EN 14399-5:2015 (E) 2 Contents Page Foreword .3 Introduction .4 1 Scope .6 2 Normative references .6 3 Dimensions .6 4 Specifications and reference standards .7 5 Designation .8 6 Marking .8 Bibliography .9
SIST EN 14399-5:2015



EN 14399-5:2015 (E) 3 Foreword This document (EN 14399-5:2015) has been prepared by Technical Committee CEN/TC 185 “Fasteners”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2015 and conflicting national standards shall be withdrawn at the latest by November 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 14399-5:2005. In comparison with EN 14399-5:2005, the following modifications have been made: — Table 1 containing the overview of the composition of bolting assemblies and component marking has been added; — a washer with a larger value of d2 (marked HD for HRD nuts) that may be supplied by
...