EN ISO 15995:2010
(Main)Gas cylinders - Specifications and testing of LPG cylinder valves - Manually operated (ISO 15995:2006)
Gas cylinders - Specifications and testing of LPG cylinder valves - Manually operated (ISO 15995:2006)
ISO 15995:2005 specifies the requirements for design, specification and type testing of dedicated LPG manually operated cylinder valves specifically for use with transportable refillable LPG cylinders from 0,5 l up to 150 l water capacity. It includes references to associated equipment for vapour or liquid service.
Gasflaschen - Spezifikation und Prüfung von Flaschenventilen für Flüssiggas (LPG) - Handbetätigt (ISO 15995:2006)
Diese Internationale Norm legt Anforderungen an Auslegung, Spezifikation und Baumusterprüfung von
handbetätigten Flaschenventilen für Flüssiggas (LPG, en: Liquified Petroleum Gas), speziell zur Verwendung
mit LPG-Gasflaschen mit einem geometrischen Volumen von 0,5 l bis einschließlich 150 l fest. Sie enthält
Verweisungen auf zugehöriges Zubehör für den Betrieb in der Gas- und Flüssigphase.
ANMERKUNG Anhang C enthält Empfehlungen für Produktionsprüfungen und -inspektionen.
Diese Internationale Norm gilt nicht für in Fahrzeugen fest eingebaute Einrichtungen.
Bouteilles à gaz - Spécifications et essais pour valves de bouteilles de GPL - Fermeture manuelle (ISO 15995:2006)
L'ISO 15995:2006 spécifie les exigences de conception, les spécifications et les essais de type des valves de bouteilles de GPL dédiées à fonctionnement manuel, spécifiquement pour être utilisées avec les bouteilles de GPL transportables rechargeables, d'une capacité en eau de 0,5 l à 150 l. Elle comprend des références aux équipements associés pour le service en phase gazeuse ou liquide.
Plinske jeklenke - Specifikacija in preskušanje ventilov za jeklenke za utekočinjeni naftni plin (UNP) - Ročno upravljanje (ISO 15995:2006)
Ta mednarodni standard določa zahteve za načrtovanje, specifikacijo in tipsko preskušanje namenskih ventilov z ročnim upravljanjem za jeklenke za utekočinjeni naftni plin (UNG) za izrecno uporabo s prenosnimi jeklenkami za utekočinjeni naftni plin za večkratno polnjenje s prostornino od 0,5 l do 150 l. Vključuje sklice na povezano opremo za oskrbo s paro ali tekočinami.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2010
1DGRPHãþD
SIST EN 13153:2002
SIST EN 13153:2002/A1:2003
3OLQVNHMHNOHQNH6SHFLILNDFLMDLQSUHVNXãDQMHYHQWLORY]DMHNOHQNH]DXWHNRþLQMHQL
QDIWQLSOLQ 813 5RþQRXSUDYOMDQMH ,62
Gas cylinders - Specifications and testing of LPG cylinder valves - Manually operated
(ISO 15995:2006)
Gasflaschen - Spezifikation und Prüfung von Flaschenventilen für Flüssiggas (LPG) -
Handbetätigt (ISO 15995:2006)
Bouteilles à gaz - Spécifications et essais pour valves de bouteilles de GPL - Fermeture
manuelle (ISO 15995:2006)
Ta slovenski standard je istoveten z: EN ISO 15995:2010
ICS:
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
23.060.40 7ODþQLUHJXODWRUML Pressure regulators
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 15995
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2010
ICS 23.020.30 Supersedes EN 13153:2001
English Version
Gas cylinders - Specifications and testing of LPG cylinder valves
- Manually operated (ISO 15995:2006)
Bouteilles à gaz - Spécifications et essais pour valves de Gasflaschen - Spezifikation und Prüfung von
bouteilles de GPL - Fermeture manuelle (ISO 15995:2006) Flaschenventilen für Flüssiggas (LPG) - Handbetätigt (ISO
15995:2006)
This European Standard was approved by CEN on 20 May 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15995:2010: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
The text of ISO 15995:2006 has been prepared by Technical Committee ISO/TC 58 “Gas cylinders” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 15995:2010 by
Technical Committee CEN/TC 286 “Liquefied petroleum gas equipment and accessories” the secretariat of
which is held by NSAI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2010, and conflicting national standards shall be withdrawn
at the latest by December 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13153:2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 15995:2006 has been approved by CEN as a EN ISO 15995:2010 without any modification.
INTERNATIONAL ISO
STANDARD 15995
First edition
2006-02-15
Gas cylinders — Specifications
and testing of LPG cylinder
valves — Manually operated
Bouteilles à gaz — Spécifications et essais pour valves de bouteilles de
GPL — Fermeture manuelle
Reference number
ISO 15995:2006(E)
©
ISO 2006
ISO 15995:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved
ISO 15995:2006(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 1
4 Design and specification . 4
4.1 General. 4
4.2 Materials . 4
4.3 Essential components. 5
4.4 Optional components. 6
4.5 Leak tightness. 7
4.6 Operating torque. 7
4.7 Opening torque . 8
4.8 Closing torque. 8
5 Valve type test. 8
5.1 General. 8
5.2 Test procedure and test requirements . 8
5.3 External and internal tightness tests (Test nos. 2, 5, 8, 11, 12, 13, 15, 16 and 17). 8
5.4 Hydraulic pressure test (Test no. 1). 10
5.5 External and internal tightness test (Test no. 2) . 10
5.6 Valve closure test (Test no. 3) . 11
5.7 Valve stem test (Test no. 4) . 11
5.8 External and internal tightness test (Test no. 5) . 11
5.9 Hand wheel fire exposure test (Test no. 6) .12
5.10 Impact test (Test no. 7). 12
5.11 External and internal tightness test (Test no. 8) . 13
5.12 Resistance to excessive closing torque test (Test no. 9). 13
5.13 Resistance to excessive opening torque test (Test no. 10) . 13
5.14 External tightness test (Test no. 11). 14
5.15 External and internal tightness test (Test no. 12) . 14
5.16 External and internal tightness test after ageing (Test no. 13). 14
5.17 Endurance test (Test no. 14). 14
5.18 External and internal tightness test (Test no. 15) . 15
5.19 External and internal tightness test — High temperature (Test no. 16). 15
5.20 External and internal tightness test — Low temperature (Test no. 17). 15
5.21 Examination of dismantled valves number 9 to 13 (Test number 18). 15
5.22 Acceptance criteria. 15
6 Documentation/Test report. 15
6.1 Documentation. 15
6.2 Test report . 16
7 Markings . 16
Annex A (normative) Valve dimensions. 17
Annex B (normative) Valves for cylinders up to and including 7,5 litre water capacity. 18
Annex C (informative) Production testing and inspection. 20
Annex D (normative) Special low temperature requirements for valves. 21
Bibliography . 22
ISO 15995:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held respon
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.