prEN ISO 11102-1
(Main)Reciprocating internal combustion engines - Handle starting equipment - Part 1: Safety requirements and tests (ISO/DIS 11102-1:2020)
Reciprocating internal combustion engines - Handle starting equipment - Part 1: Safety requirements and tests (ISO/DIS 11102-1:2020)
This document specifies requirements for handle starting equipment used on reciprocating internal combustion engines for land, rail and marine use, excluding engines used to propel road vehicle and aircraft. It can be applied to engines used to propel road construction, earth moving machines and other applications where no suitable International Standards exist.
In addition to the technical safety requirements, this document describes procedures for checking adherence to these requirements.
Hubkolben-Verbrennungsmotoren - Handkurbel-Starteinrichtungen - Teil 1: Sicherheitstechnische Anforderungen und Prüfung (ISO/DIS 11102-1:2020)
Dieses Dokument gilt für Handkurbel-Starteinrichtungen von Hubkolben-Verbrennungsmotoren für Landanlagen, Schienenfahrzeuge und Schiffsbetrieb. Ausgenommen sind Motoren zum Antrieb von Kraftfahrzeugen und Flugzeugen. Es kann auch bei Motoren zum Antrieb von Straßenbau und Erdbewegungsmaschinen und für andere Verwendungen angewendet werden, falls es für diese Motoren keine entsprechende Internationale Norm gibt.
Neben den sicherheitstechnischen Anforderungen beschreibt dieses Dokument auch Maßnahmen, mit denen die Einhaltung dieser Anforderungen überprüft werden kann.
Moteurs alternatifs à combustion interne - Dispositifs de démarrage à la manivelle - Partie 1: Exigences de sécurité et essais (ISO/DIS 11102-1:2020)
Le présent document fixe les exigences relatives aux dispositifs de démarrage à la manivelle équipant les moteurs alternatifs à combustion interne pour les applications terrestre, ferroviaire et marine, à l'exception des moteurs utilisés pour propulser les véhicules routiers et les aéronefs. Il peut s'appliquer aux moteurs utilisés pour propulser des engins de génie civil et des engins de terrassement, ainsi que dans le cadre des applications pour lesquelles il n'existe aucune Norme internationale appropriée.
Outre les exigences techniques de sécurité, le présent document décrit les modes opératoires de contrôle du respect de ces exigences.
Batni motorji z notranjim zgorevanjem - Ročna startna naprava - 1. del: Varnostne zahteve in preskusi (ISO/DIS 11102-1:2020)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2020
Batni motorji z notranjim zgorevanjem - Ročna startna naprava - 1. del: Varnostne
zahteve in preskusi (ISO/DIS 11102-1:2020)
Reciprocating internal combustion engines - Handle starting equipment - Part 1: Safety
requirements and tests (ISO/DIS 11102-1:2020)
Hubkolben-Verbrennungsmotoren - Handkurbel-Starteinrichtungen - Teil 1:
Sicherheitstechnische Anforderungen und Prüfung (ISO/DIS 11102-1:2020)
Moteurs alternatifs à combustion interne - Dispositifs de démarrage à la manivelle -
Partie 1: Exigences de sécurité et essais (ISO/DIS 11102-1:2020)
Ta slovenski standard je istoveten z: prEN ISO 11102-1
ICS:
27.020 Motorji z notranjim Internal combustion engines
zgorevanjem
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT INTERNATIONAL STANDARD
ISO/DIS 11102-1
ISO/TC 70 Secretariat: SAC
Voting begins on: Voting terminates on:
2020-01-16 2020-04-09
Reciprocating internal combustion engines — Handle
starting equipment —
Part 1:
Safety requirements and tests
Moteurs alternatifs à combustion interne — Dispositifs de démarrage à la manivelle —
Partie 1: Exigences de sécurité et essais
ICS: 27.020
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 11102-1:2020(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2020
ISO/DIS 11102-1:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
ISO/DIS 11102-1:2020(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Other regulations and requirements . 2
5 Technical safety requirements . 2
5.1 Introduction . 2
5.2 General requirements . 3
5.3 Requirements in the event of kick back . 3
6 Tests . 3
6.1 Checking angle of disengagement and travel. 3
6.2 Checking of other requirements . 3
7 Test report . 3
ISO/DIS 11102-1:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www .iso .org/ directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received. www .iso .org/ patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO's adherence to the WTO principles in the Technical
Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information
This document was prepared by Technical Committee ISO/TC 70, Internal combustion engines.
The main changes compared to the previous edition are as follows:
Clause 6.1 has been updated;
Clause 7.a) has been updated;
Clause 7.b) has been updat
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.