iTeh Standards logo
EURUSD
Your shopping cart is empty.
CEN

EN 12032:1996

(Main)

Self-adhesive tapes - Measurement of bonding of thermosetting adhesive tapes during curing

Self-adhesive tapes - Measurement of bonding of thermosetting adhesive tapes during curing

The standard specifies a method to observe the bonding of a thermosetting adhesive tape during the thermosetting process. The temperature and duration for each test shall be as the manufacturer's instructions for bonding the relevant adhesive tape.

Klebebänder - Messung der Bindefestigkeit von wärmehärtenden Klebebändern während der Vernetzung

Diese Norm legt ein Verfahren zur Ermittlung der Bindefestigkeit von wärmehärtendem Klebeband während der Vernetzung fest. Prüftemperatur und -dauer werden in den Herstelleranweisungen zum Verbinden des jeweiligen Klebebandes festgelegt.

Rubans auto-adhésifs - Mesure de la liaison des rubans thermodurcissables pendant le traitement thermique

La présente norme prescrit une méthode pour observer la liaison d'un ruban adhésif thermodurcissable pendant le traitement thermique. La température et la durée de chaque essai seront conformes aux instructions du fabricant pour réaliser la liaison du ruban adhésif concerné.

Samolepilni trakovi - Merjenje sile vezave toplotno utrdljivih lepilnih trakov med sušenjem

General Information

Status
Published
Publication Date
21-May-1996
Withdrawal Date
29-Nov-1996
ICS
83.180 - Adhesives
Technical Committee
CEN/TC 193 - Adhesives
Drafting Committee
CEN/TC 193 - Adhesives
Current Stage
9093 - Decision to confirm - Review Enquiry
Start Date
22-Oct-2020
Completion Date
23-Sep-2025
Ref Project
SIST EN 12032:1997 - Self-adhesive tapes - Measurement of bonding of thermosetting adhesive tapes during curing

Overview - EN 12032:1996 (Self-adhesive tapes, bonding during curing)

EN 12032:1996 is a CEN standard that defines a method to observe and measure the bonding behavior of thermosetting adhesive self-adhesive tapes during the curing (thermosetting) process. The standard applies when a tape’s bond forms or develops under elevated temperature and requires that the temperature and duration for each test follow the tape manufacturer’s instructions for bonding. EN 12032:1996 is intended for use in quality control, product development and verification of thermosetting adhesive tapes.

Key topics and technical requirements

  • Scope: Applies specifically to self-adhesive tapes that cure by a thermosetting (heat-activated) process.
  • Test purpose: To observe and document the development of bonding during the thermosetting cycle - i.e., how the adhesive tape forms a bond while curing.
  • Test conditions: Temperature and duration must be set according to the manufacturer’s bonding instructions for the specific tape under test. This is a mandatory requirement in the standard.
  • Measurement focus: The standard specifies a method to observe bonding during cure; practitioners should follow the procedure outlined in EN 12032:1996 to ensure consistent observation and comparability.
  • Compliance: Users should ensure adherence to the standard text and any national reproduction restrictions noted by the issuing body.

Practical applications and users

Who uses EN 12032:1996:

  • Adhesive and tape manufacturers - verifying that thermosetting tapes achieve expected bond development under recommended curing cycles.
  • R&D teams - developing new thermosetting adhesive formulations or tape constructions and assessing cure-related bonding behavior.
  • Quality control and testing laboratories - routine checks to confirm production batches meet bonding specifications when cured per manufacturer guidance.
  • End users in industries such as automotive, electronics, aerospace, and construction - ensuring bonded assemblies using thermosetting tapes meet performance requirements after cure.

Benefits of using the standard:

  • Consistent, repeatable observation of bond development during cure.
  • Alignment between manufacturer recommendations and test verification.
  • Improved confidence in the cured performance of thermosetting adhesive tapes.

Related standards

  • Refer to other CEN/EN standards on adhesives, tape performance and general test methods for additional context and complementary test procedures. For specific bonding strength metrics or post-cure mechanical tests, consult the manufacturer’s technical data and applicable industry test standards.

Keywords: EN 12032:1996, self-adhesive tapes, thermosetting adhesive tapes, measurement of bonding, curing, adhesive testing, quality control.

EN 12032:1997EN 12032:1997
PreviousNext
Standard
EN 12032:1997
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Frequently Asked Questions

EN 12032:1996 is a standard published by the European Committee for Standardization (CEN). Its full title is "Self-adhesive tapes - Measurement of bonding of thermosetting adhesive tapes during curing". This standard covers: The standard specifies a method to observe the bonding of a thermosetting adhesive tape during the thermosetting process. The temperature and duration for each test shall be as the manufacturer's instructions for bonding the relevant adhesive tape.

The standard specifies a method to observe the bonding of a thermosetting adhesive tape during the thermosetting process. The temperature and duration for each test shall be as the manufacturer's instructions for bonding the relevant adhesive tape.

EN 12032:1996 is classified under the following ICS (International Classification for Standards) categories: 83.180 - Adhesives. The ICS classification helps identify the subject area and facilitates finding related standards.

You can purchase EN 12032:1996 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of CEN standards.

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Samolepilni trakovi - Merjenje sile vezave toplotno utrdljivih lepilnih trakov med sušenjemKlebebänder - Messung der Bindefestigkeit von wärmehärtenden Klebebändern während der VernetzungRubans auto-adhésifs - Mesure de la liaison des rubans thermodurcissables pendant le traitement thermiqueSelf-adhesive ta
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

Loading comments...

This May Also Interest You

CEN
EN 15416-3:2025(Main)
Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 3: Creep deformation test at cyclic climate conditions with specimens loaded in bending shear
SIST EN 15416-3:2025

This document specifies a method for determining the creep deformation of bonded specimens loaded in bending shear. It is applicable to adhesives used in load bearing timber structures.
It is applicable for assessing the compliance of adhesives to EN 15425 and EN 16254.
This test is intended primarily to obtain performance data for the classification of adhesives for load bearing timber structures according to their suitability for use in defined climatic environments.
This method is not intended to provide data for structural design and does not necessarily represent the performance of the bonded member in service.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15416-4:2025(Main)
Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 4: Determination of open assembly time under referenced conditions
SIST EN 15416-4:2025

This document specifies a laboratory method of determining the open assembly time under referenced conditions in standard climate (20 ± 2) °C and (65 ± 5) % relative humidity (hereafter climate [20/65]).
The method gives a result that cannot be applied to the safe manufacture of timber structures without taking into account the influence of factors such as timber density, moisture content, factory temperature and relative air humidity.

  • Standard
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15416-5:2025(Main)
Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 5: Determination of minimum pressing time under referenced conditions
SIST EN 15416-5:2025

This document specifies a laboratory method of determining the minimum pressing time for glue line thicknesses close contact, 0,2 mm, 0,3 mm and 0,5 mm, at three temperatures and three wood moisture contents.
This document is intended to determine the minimum pressing time using a specified procedure for obtaining a reliable base for comparison of minimum pressing time between adhesives under referenced conditions.
The method gives a result that cannot be applied to the safe manufacture of timber structures without taking into account the influence in variation of factors such as timber density, wood moisture content, factory temperature and relative air humidity.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15416-1:2025(Main)
Adhesives for load bearing timber structures other than phenolic and aminoplastic - Test methods - Part 1: Long-term tension load test perpendicular to the bond line at varying climate conditions with specimens perpendicular to the glue line (Glass house test)
SIST EN 15416-1:2025

This document specifies a method of determining the ability of adhesive bonds to resist long-term sustained load applied vertical to the glue lines. It is applicable to adhesives used in load-bearing timber structures.
It is applicable for the following applications:
a)   for assessing the compliance of adhesives according to EN 15425 and EN 16254;
b)   for assessing the effect on the bond strength resulting from long-term sustained load at cyclic climate conditions.
This method is intended primarily to obtain performance data for the classification of adhesives for load bearing timber structures according to their suitability for use in defined climatic environments.
This method is not intended to provide data for structural design and does not necessarily represent the performance of the bonded member in service.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 18070:2025(Main)
Performance of wood adhesives exposed to high temperatures with regard to behaviour of load-bearing timber structures in fire - Test method, evaluation and classification
SIST EN 18070:2025

This document specifies a test method for comparing the compression shear strength of adhesive bonds in wood and solid wood after exposure to a target temperature for a specified duration of time.
This document is applicable to adhesives used in load bearing timber structures.
This document is not applicable to Epoxy- and two component Polyurethane-adhesives.
This method is intended to obtain data for the performance of wood adhesives at very high temperatures. The result of this comparison can be used to classify the adhesive with regard to the behaviour of load-bearing timber structures in fire.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 29862:2024(Main)
Self adhesive tapes - Determination of peel adhesion properties (ISO 29862:2024)
SIST EN ISO 29862:2025

This document specifies a series of methods for the determination of peel adhesion properties of self adhesives tapes.
This document specifies:
—     Method 1: Self adhesive tapes – Measurement of peel adhesion from stainless steel at an angle of 180°;
—     Method 2: Self adhesive tapes – Measurement of peel adhesion from its own backing at an angle of 180°;
—     Method 3: Self adhesive tapes – Measurement of peel adhesion of double-sided and transfer tapes at an angle 180°;
—     Method 4: Self adhesive tapes – Measurement of adhesion of the liner to an adhesive tape at an angle of 180°.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 10364:2024(Main)
Structural adhesives - Determination of the pot life (working life) of multi-component adhesives (ISO 10364:2024)
SIST EN ISO 10364:2024

This document specifies methods for determining the pot life of multi-part adhesives, in order to be able to determine whether the pot life conforms to the minimum specified working life required of an adhesive.
The different methods described in this document to measure the property do not necessarily provide identical results.
The test methods described are suitable for assessing all multi–part adhesives, and especially epoxy based and polyurethane based adhesives, but they are not suitable for some acrylic-based adhesives.
NOTE 1       Some of the methods described in this document can also be suitable for determination of working life of one-part adhesives that react to humidity (e.g. PUR prepolymers).
NOTE 2       This document can also be used for assessing non-structural adhesives.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 21368:2023(Main)
Adhesives - Guidelines for the fabrication of adhesively bonded structures and reporting procedures suitable for the risk evaluation of such structures (ISO 21368:2022)
SIST EN ISO 21368:2023

This document provides guidelines describing the adhesive bonding quality requirements suitable for use by adhesive user-companies utilizing adhesive bonding as a means of fabrication. In particular, the guidelines define various approaches to meeting quality requirements for fabrication and reporting procedures, both in workshops and on site. These guidelines aim to convey the importance of maintaining quality standards in fabrication and reporting procedures, keeping records and thus enabling documentation to provide the basis for risk evaluation of adhesively bonded structures in service and in use.
These guidelines have been prepared such that:
a) they are independent of the type of adhesively bonded structure;
b) they are independent of adhesive user-companies’ and suppliers’ product recommendations;
c) they define the quality requirements for adhesive bonding in terms of fabrication and reporting procedures, both in workshops and on site;
d) they can be used as the basis for risk evaluation of adhesively bonded structures in service and in use;
e) they can be used as a basis for assessing a fabricator's capability to produce adhesively bonded structures fulfilling specified quality requirements when they are detailed in one or more of the following:
—    a contract between the parties involved;
—    an application standard;
—    a regulatory statement.
The guidelines contained within this document can be adopted in full or selectively chosen by the adhesive user to suit the structure concerned. The guidelines provide a flexible framework for the control of adhesive bonding activities in the following cases.
Case 1
The provision of specific requirements for adhesive bonding in contracts that require the adhesive user to have a quality system other than ISO 9001.
Case 2
The provision of specific requirements for adhesive bonding as guidance to an adhesive user developing a quality system.
Case 3
The provision of specific requirements for references in application standards that uses adhesive bonding as part of its requirements or in a contract between relevant parties.
Case 4
The provision of a framework for fabrication and reporting procedures to a quality standard, suitable in particular as a basis for the risk evaluation of adhesively bonded structures.

  • Standard
    111 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 6076:2023(Main)
Adhesives - Installation of floor coverings, wood flooring, levelling compounds and tiles - Specification of trowel notch sizes (ISO 6076:2023, Corrected version 2023-09)
SIST EN ISO 6076:2023

This document specifies the individual measurements of notches. It assigns specific codes used to label notched tools according to the measurements and tolerances specified in this document.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 302-8:2023(Main)
Adhesives for load-bearing timber structures - Test methods - Part 8: Static load test of multiple bond line specimens in compression shear
SIST EN 302-8:2023

This document specifies a method of determining the ability of adhesive bonds to resist static load. It is applicable to adhesives used in load bearing timber structures.
It is applicable for the following applications:
a) for assessing the compliance of adhesives according to EN 301, EN 15425, EN 16254, EN 17334 and EN 17418;
b) for assessing the suitability and quality of adhesives for load-bearing timber structures;
c) for assessing the effect on the bond strength resulting from constant load at different climate conditions.
This method is intended primarily to obtain performance data for the classification of adhesives for load bearing timber structures according to their suitability for use in defined climatic environments.
This method is not intended to provide data for structural design and does not necessarily represent the performance of the bonded member in service.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day