EN 573-5:2007

Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 5: Codification of standardized wrought products

This document specifies the codification of some standardized semifinished wrought products for use in ordering information.
NOTE   Codification is usually required for technical drawings.
It does not apply to castings, cast forging stock, rolling ingots, extrusion billets and ingots for remelting.

Aluminium und Aluminiumlegierungen - Chemische Zusammensetzung und Form von Halbzeug - Teil 5: Bezeichnung von genormten Kneterzeugnissen

Dieser Teil der EN 573 legt die Bezeichnung von einigen genormten Knet- Halbzeugen fest. Er gilt nicht für Gußstücke, gegossenes Schmiedevormaterial, Walzbarren, Preßbarren und Masseln.

Aluminium et alliages d'aluminium - Composition chimique et forme des produits corroyés - Partie 5: Codification des produits corroyés normalisés

Cette partie de l'EN 573 spécifie la codification de certains demi-produits corroyés normalisés. Elle ne s'applique pas aux pièces moulées, ébauches de forgeage coulées, plaques de laminage, billettes de filage et lingots pour refusion.

Aluminij in aluminijeve zlitine - Kemična sestava in oblika gnetenih izdelkov – 5. del: Kodiranje standardiziranih gnetenih izdelkov

General Information

• Status: Published
• Publication Date: 11-Sep-2007
• Withdrawal Date: 30-Mar-2008
• ICS: 77.040.30 - Chemical analysis of metals
• ICS: 77.120.10 - Aluminium and aluminium alloys
• Technical Committee: CEN/TC 132 - Aluminium and aluminium alloys
• Drafting Committee: CEN/TC 132/WG 7 - Sheets, strips and plates
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 02-Dec-2023
• Ref Project: SIST EN 573-5:2007 - Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 5: Codification of standardized wrought products

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aluminium und Aluminiumlegierungen - Chemische Zusammensetzung und Form von Halbzeug - Teil 5: Bezeichnung von genormten KneterzeugnissenAluminium et alliages d'aluminium - Composition chimique et forme des produits corroyés - Partie 5: Codification des produits corroyés normalisésAluminium and aluminium alloys - Chemical composition and form of wrought products - Part 5: Codification of standardized wrought products77.150.10Aluminijski izdelkiAluminium products77.040.30Kemijska analiza kovinChemical analysis of metalsICS:Ta slovenski standard je istoveten z:EN 573-5:2007SIST EN 573-5:2007en,fr,de01-december-2007SIST EN 573-5:2007SLOVENSKI
STANDARD



SIST EN 573-5:2007



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 573-5September 2007ICS 77.040.30; 77.120.10 English VersionAluminium and aluminium alloys - Chemical composition andform of wrought products - Part 5: Codification of standardizedwrought productsAluminium et alliages d'aluminium - Composition chimiqueet forme des produits corroyés - Partie 5: Codification desproduits corroyés normalisésAluminium und Aluminiumlegierungen - ChemischeZusammensetzung und Form von Halbzeug - Teil 5:Bezeichnung von genormten KneterzeugnissenThis European Standard was approved by CEN on 13 August 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 573-5:2007: ESIST EN 573-5:2007



EN 573-5:2007 (E) 2 Contents page Foreword.3 Introduction.4 1 Scope.5 2 Normative references.5 3 Terms and definitions.5 4 Codification system.5 Figure 1 — Structure of codification system.5 Table 1 — Codification for dimension and form of extruded and drawn products.7 Table 2 — Codification for dimension and form of rolled products.7 Table 3 — Other examples for wrought forging stock.8 Table 4 — Other examples for wire and drawing stock.8 Table 5 — Other examples for extruded and drawn products.10 Table 6 — Other examples for rolled products.11 Bibliography.12
SIST EN 573-5:2007



EN 573-5:2007 (E) 3 Foreword This document (EN 573-5:2007) has been prepared by Technical Committee CEN/TC 132 “Aluminium and alumini
...