Methods of test for mortar for masonry - Part 7: Determination of air content of fresh mortar

This European Standard specifies two methods for determining the air content of fresh mortars including those containing mineral binders and both dense and lightweight aggregates: Method A "The pressure method" and Method B "The alcohol method". For air content less than 20 %, method A is applicable. For air content of 20% or more, method B is applicable.

Prüfverfahren für Mörtel für Mauerwerk - Teil 7: Bestimmung des Luftgehaltes von Frischmörtel

Diese Europäische Norm legt zwei Verfahren zur Bestimmung des Luftgehaltes von Frischmörteln einschließlich Frischmörtel aus mineralischen Bindemitteln und sowohl dichten Zuschlägen als auch Leichtzuschlägen fest. Verfahren A: das "Druck-Verfahren" und Verfahren B: das "Alkohol-Verfahren". Bei einem Luftgehalt von weniger als 20% ist Verfahren A anzuwenden. Bei einem Luftgehalt von mehr als 20 % ist Verfahren B anzuwenden.

Méthodes d'essai des mortiers pour maçonnerie - Partie 7: Détermination de la teneur en air du mortier frais

La présente norme européenne spécifie deux méthodes pour déterminer la teneur en air des mortiers frais, y compris les mortiers contenant des liants minéraux et à la fois des granulats lourds et légers: - méthode A: méthode par pression; - méthode B: méthode à l'alcool. La méthode A est applicable aux mortiers dont la teneur en air est inférieure à 20 %. La méthode B est applicable aux mortiers dont la teneur en air est égale ou supérieure à 20 %.

Metode preskušanja zidarskih malt - 7. del: Določevanje zraka v sveži malti

General Information

Status

Published

Publication Date

20-Oct-1998

ICS

91.100.10 - Cement. Gypsum. Lime. Mortar

Technical Committee

CEN/TC 125 - Masonry

Drafting Committee

CEN/TC 125/WG 4 - Test methods

Current Stage

9020 - Submission to 2 Year Review Enquiry - Review Enquiry

Start Date

15-Jul-2024

Completion Date

15-Jul-2024

Directive

305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec

89/106/EEC - Construction products

Mandate

M/128 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on products for concrete, mortar and grout

Ref Project

SIST EN 1015-7:1999 - Methods of test for mortar for masonry - Part 7: Determination of air content of fresh mortar

Buy Standard

Standard

EN 1015-7:1999

English language

10 pages

sale 10% off

Preview

sale 10% off

Preview

e-Library read for

1 day

Create e-Library subscription and get permanent access to the document. Subscriptions are available for: 91 91.100 91.100.10

Standards Content (Sample)

EN 1015-7:1999

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Prüfverfahren für Mörtel für Mauerwerk - Teil 7: Bestimmung des Luftgehaltes von FrischmörtelMéthodes d'essai des mortiers pour maçonnerie - Partie 7: Détermination de la teneur en air du mortier fraisMethods of test for mortar for masonry - Part 7: Determination of air content of fresh mortar91.100.10Cement. Mav
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN

EN 15824:2017(Main)

Specifications for external renders and internal plasters based on organic binders

SIST EN 15824:2017

This European Standard is applicable to factory-made renders and plasters based on organic binders used for external or internal covering on walls, columns, partitions and ceilings. The products are manufactured in paste form, ready to use, or in powder form. This European Standard is also applicable to renders and plasters with inorganic binders such as silicates, silanes, siloxanes and silicones.
Renders and plasters can form the final surface of the structure, textured or not, or they can provide a levelling of the substrate, adequately smooth for subsequent decorative treatments.
This European Standard contains definitions and final performance requirements. It includes relevant characteristic categories to designate renders and plasters.
This European Standard provides for the assessment and verification of constancy of performance (AVCP) of the product to this European Standard. The marking requirement for products covered by this European Standard is included.
This European Standard is not applicable to coating materials and coating systems according to EN 1062-1 and EN 13300.
This European Standard does not contain recommendations for the design and application of renders and plasters. However, this European Standard may be used for definition of renders and plasters in conjunction with codes of application and national specifications for execution of works.

Standard
19 pages
English language
sale 10% off
e-Library read for
1 day

27-Jun-2017
30-Mar-2019
91.100.10
305/2011
M/109
M/116
CEN/TC 125

CEN

EN 998-1:2016(Main)

Specification for mortar for masonry - Part 1: Rendering and plastering mortar

SIST EN 998-1:2017

This European Standard is applicable to factory-made rendering/plastering mortars based on inorganic binders for external (rendering) and internal (plastering) use on walls, ceilings, columns and partitions. It contains definitions and final performance requirements.
This European Standard provides for the assessment and verification of constancy of performance (AVCP) of the product to this European Standard. The marking requirement for products covered by this European Standard is included.
It does not cover mortars where calcium sulphate binder is the principal active binding agent.
Calcium sulphate binder can be used as an additional binder together with air lime. If air lime is the principal active binding component, the rendering/plastering mortar is covered by this European Standard. If the calcium sulphate binder is the principal active binding component, the mortar is covered by EN 13279.
Special fire resistant- and acoustical mortars, mortars for structural repair and surface treatments of building elements such as materials for smoothing or trueing, paints, coatings, thin-layer organic renders/plasters and prefabricated units (e.g. plasterboards) are not dealt with in this European Standard.
This European Standard covers rendering/plastering mortars defined in Clause 3 with the exception of site-made rendering/plastering mortars. However, this European Standard or part of this European Standard may be used in conjunction with codes of application and national specifications covering site-made mortar.

Standard
25 pages
English language
sale 10% off
e-Library read for
1 day

CEN

EN 998-2:2016(Main)

Specification for mortar for masonry - Part 2: Masonry mortar

SIST EN 998-2:2017

This European Standard specifies requirements for factory-made masonry mortars (bedding, jointing and pointing) for use in masonry walls, columns and partitions (e.g. facing and rendered masonry, load bearing or non-load bearing masonry structures for buildings and civil engineering works).
This European Standard defines for fresh mortar the performance related to workable life, chloride content, air content, density and correction time (for thin-layer mortar only). For hardened mortar it defines, e.g. performances related to compressive strength, bond strength, density measured according to the corresponding test methods contained in separate European Standards.
This European Standard provides for the assessment and verification of constancy of performance (AVCP) of the product to this European Standard. The marking requirement for products covered by this European Standard is included.
This European Standard covers masonry mortars defined in Clause 3 with the exception of site made mortar. However, this European Standard or part of this European Standard may be used in conjunction with codes of application and national specifications covering site made mortar.

Standard
28 pages
English language
sale 10% off
e-Library read for
1 day

08-Nov-2016
30-Aug-2018
91.100.10
305/2011
89/106/EEC
M/116
CEN/TC 125

CEN

EN 1015-12:2016(Main)

Methods of test for mortar for masonry - Part 12: Determination of adhesive strength of hardened rendering and plastering mortars on substrates

SIST EN 1015-12:2016

This European Standard specifies a method for the determination of the adhesive strength between rendering and plastering mortars and a substrate.

Standard
10 pages
English language
sale 10% off
e-Library read for
1 day

CEN

EN 13914-1:2016(Main)

Design, preparation and application of external rendering and internal plastering - Part 1: External rendering

SIST EN 13914-1:2016

This European Standard specifies requirements and recommendations for the design, preparation and application of
-   renders based on cement, lime or other mineral binders, and/or combinations thereof, masonry cement and polymer modified binder based external renderings, in accordance with FprEN 998-1 or site made renders;
-   renders based on organic binders in accordance with FprEN 15824
on all common types of backgrounds. It includes rendering on both new and old backgrounds and the maintenance and repair of existing work. This document gives guidance on the use of established site, factory and semi-finished factory made renders.
This document does not cover the following:
a)   the use and application of special renders for liquid retaining structures, e.g. coatings, and for backgrounds to cladding systems;
b)   the structural repair of concrete;
c)   the installation of external thermal insulation composite systems (ETICS);
d)   the specification and use of sealants used to seal joints for use with rendering;
e)   the use of gypsum based renders used externally, but their use may be permitted in some countries;
Gypsum based products soften when subject to prolonged moist conditions. The use of such products externally will depend upon the climatic conditions where the render will be used and on the local building traditions. With the exception of some drier countries in southern Europe gypsum based renders are generally not recommended for external use and are therefore not included within the scope of this document. However, their use may be permitted and controlled locally. )
f)   renders on historical monuments or buildings in protected areas which may be regulated by national codes;
g)   the design and installation of flashings at windowsills and elsewhere.
Because of the many and varied materials and practices and different climatic conditions in Europe it is not possible for certain aspects of the standard to enter into sufficient detail to be fully usable to practitioners in each country. Appropriate guidance to complement, but not alter any basic European recommendations is given in documentation prepared by each country. Aspects of this European Standard whose basic recommendations may need to be complemented are indicated where they occur by a footnote referencing this clause.

Standard
61 pages
English language
sale 10% off
e-Library read for
1 day

CEN

EN 13914-2:2016(Main)

Design, preparation and application of external rendering and internal plastering - Part 2: Internal plastering

SIST EN 13914-2:2016

This European Standard deals with the design considerations and essential principles for internal plastering systems and application of plastering systems.
The different parts of the EN 13914 series of standards specify requirements and recommendations for detailing, design and material considerations, the selection of mixes and the application of gypsum plasters, gypsum/lime plasters, lightweight plasters, lime/gypsum-, cement- and cement/lime-based plasters, lime-based plasters, clay plasters, silicate plasters, organic plasters, polymer-modified plasters, etc.
This standard does not deal with the following:
-   external finishes;
-   painting and/or preparation;
-   impregnations;
-   structural repair of concrete;
-   prefabricated fibre-reinforced plaster elements.
Owing to the many and varied materials and practices and different climatic conditions in Europe it is not possible for certain aspects of the standard to enter into sufficient detail to be fully usable to practitioners in each country. Such guidance to complement, but not alter, any basic European recommendations is given in documentation prepared by each country. Aspects of this European Standard, the basic recommendations of which may need to be complemented, are indicated where they occur by a footnote referencing this clause.