EN ISO 178:2003/A1:2005

Plastics - Determination of flexural properties - Amendment 1: Precision statement (ISO 178:2001/A1:2004)

Kunststoffe - Bestimmung der Biegeeigenschaften - Änderung 1: Angaben zur Präzision (ISO 178:2004/A1:2004)

Plastiques - Détermination des propriétés en flexion - Amendement 1: Déclaration de fidélité (ISO 178:2001/A1:2004)

Navedba natančnosti (ISO 178:2001/Amd 1:2004)

General Information

• Status: Withdrawn
• Publication Date: 18-Jan-2005
• Withdrawal Date: 14-Dec-2010
• ICS: 83.080.01 - Plastics in general
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249 - Plastics
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 15-Dec-2010
• Completion Date: 15-Dec-2010
• Ref Project: SIST EN ISO 178:2003/A1:2005 - Plastics - Determination of flexural properties - Amendment 1: Precision statement (ISO 178:2001/A1:2004)

Relations

• Replaced By: EN ISO 178:2010 - Plastics - Determination of flexural properties (ISO 178:2010)
• Effective Date: 08-Jan-2011
• Amends: EN ISO 178:2003 - Plastics - Determination of flexural properties (ISO 178:2001)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
01-maj-2005
1DYHGEDQDWDQþQRVWL,62$PG
Plastics - Determination of flexural properties - Amendment 1: Precision statement (ISO
178:2001/A1:2004)
Kunststoffe - Bestimmung der Biegeeigenschaften - Änderung 1: Angaben zur Präzision
(ISO 178:2004/A1:2004)
Plastiques - Détermination des propriétés en flexion - Amendement 1: Déclaration de
fidélité (ISO 178:2001/A1:2004)
Ta slovenski standard je istoveten z: EN ISO 178:2003/A1:2005
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 178:2003/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2005
ICS 83.080.01
English version
Precision statement (ISO 178:2001/Amd 1:2004)
Déclaration de fidélité (ISO 178:2001/Amd 1:2004)
This amendment A1 modifies the European Standard EN ISO 178:2003; it was approved by CEN on 24 December 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Central Secretariat or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 178:2003/A1:2005: E
worldwide for CEN national Members.

Foreword
The text of ISO 178:2001/Amd 1:2004 has been prepared by Technical Committee ISO/TC 61
"Plastics” of the International Organization for Standardization (ISO) and has been taken over as
which is held by IBN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by July 2005, and conflicting national standards
shall be withdrawn at the latest by July 2005.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Endorsement notice
The text of ISO 178:2001/Amd 1:2004 has been approved by CEN as EN ISO
178:2003/A1:2005 without any modifications.

INTERNATIONAL ISO
STANDARD 178
Fourth edition
2001-12-15
AMENDMENT 1
2004-02-15
Plastics — Determination of flexural
properties
AMENDMENT 1: Precision statement
Plastiques — Détermination des propriétés en flexion
AMENDEMENT 1: Déclaration de fidélité

Reference number
ISO 178:2001/Amd.1:2004(E)
©
ISO 2004
ISO 178:2001/Amd.1:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
W
...