EN 13035-5:2006/prA1

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 5: Machines and installations for stacking and de-stacking

Maschinen und Anlagen zur Herstellung, Be- und Verarbeitung von Flachglas – Sicherheitsanforderungen - Teil 5: Maschinen und Einrichtungen zum Stapeln und Abstapeln

Machines et installations pour la production, le façonnage et la transformation du verre plat - Exigences de sécurité - Partie 5: Machines et installations à empiler et dépiler

Stroji in obrati za proizvodnjo, obdelavo in predelavo ravnega stekla - Varnostne zahteve - 5. del: Stroji in naprave za zlaganje in razlaganje

General Information

• Status: Not Published
• ICS: 81.100 - Equipment for the glass and ceramics industries
• Technical Committee: CEN/TC 151 - Construction equipment and building material machines - Safety
• Drafting Committee: CEN/TC 151/WG 13 - Machines and plants for the production, treatment and processing of flat, hollow and special glass - Safety
• Current Stage: 5060 - Closure of Vote - Formal Approval
• Start Date: 07-Oct-2009
• Completion Date: 07-Oct-2009
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Directive: 98/37/EC - Machinery
• Mandate: M/079 - Mandate to CEN and CENELEC for standardization in the field of machines
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: SIST EN 13035-5:2007/kprA1:2009 - Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 5: Machines and installations for stacking and de-stacking

Relations

• Merged Into: EN 13035-5:2006+A1:2009 - Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 5: Machines and installations for stacking and de-stacking
• Effective Date: 18-Jan-2023
• Amends: EN 13035-5:2006 - Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 5: Machines and installations for stacking and de-stacking
• Effective Date: 22-Dec-2008

Standards Content (Sample)

SLOVENSKI STANDARD
01-julij-2009
Stroji in obrati za proizvodnjo, obdelavo in predelavo ravnega stekla - Varnostne
zahteve - 5. del: Stroji in naprave za zlaganje in razlaganje
Machines and plants for the manufacture, treatment and processing of flat glass - Safety
requirements - Part 5: Machines and installations for stacking and de-stacking
Maschinen und Anlagen zur Herstellung, Be- und Verarbeitung von Flachglas –
Sicherheitsanforderungen - Teil 5: Maschinen und Einrichtungen zum Stapeln und
Abstapeln
Machines et installations pour la production, le façonnage et la transformation du verre
plat - Exigences de sécurité - Partie 5: Machines et installations à empiler et dépiler
Ta slovenski standard je istoveten z: EN 13035-5:2006/prA1
ICS:
81.100 2SUHPD]DVWHNODUVNRLQ Equipment for the glass and
NHUDPLþQRLQGXVWULMR ceramics industries
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
FINAL DRAFT
EN 13035-5:2006
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
May 2009
ICS 81.100
English Version
Machines and plants for the manufacture, treatment and
processing of flat glass - Safety requirements - Part 5: Machines
and installations for stacking and de-stacking
Machines et installations pour la production, le façonnage Maschinen und Anlagen zur Herstellung, Be- und
et la transformation du verre plat - Exigences de sécurité - Verarbeitung von Flachglas - Sicherheitsanforderungen -
Partie 5: Machines et installations à empiler et dépiler Teil 5: Maschinen und Einrichtungen zum Stapeln und
Abstapeln
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 151.
This draft amendment A1, if approved, will modify the European Standard EN 13035-5:2006. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13035-5:2006/prA1:2009: E
worldwide for CEN national Members.

Contents Page
Foreword .3
1 Modification to the Foreword .4
2 Modification to the Introduction .4
3 Modification to the Scope .4
4 Modification to Clause 2, Normative references .4
5 Modification to Clause 4, List of significant hazards .5
6 Modification to Clause 5, Safety requirements and/or protective measures .6
7 Modification to Clause 6, Verification of the safety requirements and/or protective
measures .8
8 Modification to Clause 7, Information for use .9
9 Addition of Annex ZB .9
10 Modification to the Bibliography . 10

Foreword
This document (EN 13035-5:2006/prA1:2009) has been prepared by Technical Committee CEN/TC 151
“Construction equipment and building material machines — Safety”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.
1 Modification to the Foreword
th
Replace the 4 paragraph with:
“For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document.”
2 Modification to the Introduction
In the last paragraph, replace “prEN 13035-1” with “EN 13035-1”.

3 Modification to the Scope
st
In 1.2, replace the 1 sentence with:
“This European Standard deals with the significant hazards, hazardous situations and events relevant to ma-
chines and installations for stacking and de-stacking flat glass when they are used as intended and under the
conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).”
rd
In 1.2, replace the 3 sentence with:
“This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising
from the significant hazards during commissioning, operation and maintenance.”
Add the following new 1.7:
“1.7 Noise is not a significant hazard for this type of machinery. The A-weighted emission sound pressure
level at workstations does not exceed 70 dB(A).”

4 Modification to Clause 2, Normative references
Delete:
"EN 294:1992, Safety of machinery — Safety distance to prevent danger zones being reached by the upper
limbs
EN 418:1992, Safety of machinery — Emergency stop equipment, functional aspects — Principles for design”
“EN 954-1:1996, Safety of machinery — Safety-related parts of control systems — Part 1: General principles
for design”
“EN 1050:1996, Safety of machinery — Principles for risk assessment”
Replace "EN 60204-1:1997" with “EN 60204-1:2006, Safety of machinery — Electrical equipment of machines
— Part 1: General requirements (IEC 60204-1:2005, modified)”.
Delete:
“prEN 61496-2:2005, Safety of machinery — Electro-sensitive protective equipment — Part 2: Particular re-
quirements for equipment using active opto-electronic protective devices (AOPDs) (IEC 61496-2:2005)”
Add:
"CLC/TS 61496-2, Safety of machinery — Electro-sensitive protective equipment — Part 2: Particular re-
quirements for equipment using active opto-electronic protective devices (AOPDs) (IEC 61496-2:2006)”
“EN ISO 13849-1:2008, Safety of machinery — Safety-related parts of control systems — Part 1: General
principles for design (ISO 13849-1:2006)
EN ISO 13850, Safety of machinery — Emergency stop — Principles for design (ISO 13850:2006)
EN ISO 13857:2008, Safety of machinery - Safety distances to prevent hazard zones being reached by upper
and lower limbs (ISO 13857:2008)"

5 Modification to Clause 4, List of significant hazards
Replace Table 1 with the following:
"
Preventive
Hazards Danger zone/dangerous items measures:
see clause
4.1 Mechanical  
4.1.1 Crushing and Machinery, fixed type: 5.2 to 5.5
impact between moving loading and stacking mechanism with or
without flat glass and fixed part of the machinery itself or
other machines or transport devices, e.g. conveyors,
stillages. Risk of impact only for cycles of less than 20 s.
4.1.2 Crushing and Machinery, fixed type: 5.2 to 5.5
impact by the back and forth movement and the rotation of platforms
for stillages with or without stillage (loaden or unloaden)
4.1.3 Crushing and Machinery, movable type: 5.2 to 5.4
impact the same risks as for 4.1.1 and 4.1.2 apply.
4.1.4 Crushing and Machinery, movable type, in addition: 5.2 to 5.4; 5.15
impact by the travelling movement of machinery and b
...