EN 13035-7:2006+A1:2009

Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 7: Cutting machines for laminated glass

1.1   This European Standard applies for cutting machines for laminated glass including the following steps: transport and positioning, synchronous cutting (scoring) from both sides, break-out, electrical heating and separation.
1.2   This European Standard deals with the significant hazards, hazardous situations and events relevant to cutting machines for laminated glass when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4). Those hazards, which are dealt with in the ad-hoc standard EN 619 for conveyors are excepted. This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards during commissioning, operation and maintenance. Hazards from noise are not considered to be significant.
1.3   This European Standard is not applicable to cutting (scoring) and break-out of monolithic glass (see EN 13035-3 and EN 13035-6).
1.4   This European Standard is not applicable to the cutting of laminated glass by sawing or by the use of high-pressure liquid.
1.5   This European Standard is not applicable to the significant hazards of conveyors and machines for the manufacture, treatment and processing of flat glass such as tilting tables.
1.6   This European Standard is not applicable to cutting machines for laminated glass which are manufactured before the date of publication of this European Standard by CEN.

Maschinen und Anlagen zur Herstellung, Be- und Verarbeitung von Flachglas - Sicherheitsanforderungen - Teil 7: Schneidmaschinen für Verbundglas

Machines et installations pour la production, le façonnage et la transformation du verre plat - Prescriptions de sécurité - Partie 7: Machines à couper le verre feuilleté

1.1   La présente Norme européenne s'applique aux machines à couper le verre feuilleté, pour les étapes suivantes : transport et mise en place, découpe (marquage de coupe) synchronisée des deux côtés, rompage, chauffage électrique et séparation.
1.2   !La présente Norme européenne traite les phénomènes dangereux, situations et événements dangereux significatifs spécifiques aux machines à couper le verre feuilleté, lorsqu'elles sont utilisées normalement et dans les conditions d’utilisation raisonnablement prévisibles par le fabricant (voir Article 4)." Les phénomènes dangereux traités dans la norme spécifique EN 619 pour les convoyeurs ne sont pas pris en compte. !La présente Norme européenne spécifie les mesures techniques appropriées pour éliminer ou réduire les risques susceptibles d’être engendrés par les phénomènes dangereux significatifs lors des opérations de mise en service, de fonctionnement et de maintenance."
1.3   La présente Norme européenne ne s'applique pas au découpage (marquage de coupe) ni au rompage du verre monolithique (voir EN 13035-3 et EN 13035-6).
1.4   La présente Norme européenne ne s'applique pas au découpage du verre feuilleté par sciage ou utilisation d'un liquide sous pression.
1.5   La présente Norme européenne ne s'applique pas aux phénomènes dangereux significatifs des convoyeurs et des machines pour la production, le façonnage et la transformation du verre plat, par exemple les tables basculantes.
1.6   La présente Norme européenne ne s’applique pas aux machines à couper le verre feuilleté fabriquées avant la date de publication de la présente Norme européenne par le CEN.

Stroji in obrati za proizvodnjo, obdelavo in predelavo ravnega stekla - Varnostne zahteve - 7. del: Stroji za rezanje lepljenega stekla

Ta evropski standard velja za stroje za rezanje za lepljeno steklo, vključno z naslednjimi koraki: prevoz in namestitev, sinhrono rezanje (zarezovanje) z obeh strani, lomljenje, električno segrevanje in ločevanje. Ta evropski standard obravnava velike nevarnosti, nevarne situacije in primere, ki se tičejo strojev za rezanje lepljenega stekla, kadar se uporabljajo v skladu z namembnostjo in pod pogoji napačne uporabe, ki jih upravičeno predvidel proizvajalec (glej Klavzulo 4). Te nevarnosti, ki jih obravnava temu namenjen standard EN 619 za transporterji, so pričakovane. Ta evropski standard opredeljuje ustrezne tehnične ukrepe za odpravo ali zmanjševanje tveganj, ki nastanejo zaradi velikih nevarnosti med usposobitvijo za zagon, obratovanjem in vzdrževanjem. Nevarnosti zaradi hrupa se ne štejejo kot velike. Ta standard ne velja za rezanje (zarezovanje) in lomljenje stekla iz enega kosa (glej EN 13035-3 in EN 13035-6). Ta evropski standard ne velja za rezanje lepljenega stekla z žaganjem ali z uporabo tekočine pod visokim pritiskom. Ta evropski standard ne velja za velike nevarnosti pri transporterjih in strojih za izdelavo, obdelavo in predelavo ravnega stekla, kot so nagibne mize. 1.6. Ta evropski standard ne velja za stroje za rezanje za lepljeno steklo, ki so bili izdelani pred datumom, ko je CEN objavil ta evropski standard.

General Information

• Status: Published
• Publication Date: 01-Dec-2009
• ICS: 81.100 - Equipment for the glass and ceramics industries
• Technical Committee: CEN/TC 151 - Construction equipment and building material machines - Safety
• Drafting Committee: CEN/TC 151/WG 13 - Machines and plants for the production, treatment and processing of flat, hollow and special glass - Safety
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 19-May-2021
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Directive: 98/37/EC - Machinery
• Mandate: M/079 - Mandate to CEN and CENELEC for standardization in the field of machines
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: SIST EN 13035-7:2007+A1:2010 - Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 7: Cutting machines for laminated glass

Relations

• Merged From: EN 13035-7:2006/prA1 - Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 7: Cutting machines for laminated glass
• Effective Date: 18-Jan-2023
• Merged From: EN 13035-7:2006 - Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 7: Cutting machines for laminated glass
• Effective Date: 03-Oct-2009

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Stroji in obrati za proizvodnjo, obdelavo in predelavo ravnega stekla - Varnostne zahteve - 7. del: Stroji za rezanje lepljenega steklaMaschinen und Anlagen zur Herstellung, Be- und Verarbeitung von Flachglas - Sicherheitsanforderungen - Teil 7: Schneidmaschinen für VerbundglasMachines et installations pour la production, le façonnage et la transformation du verre plat - Exigences de sécurité - Partie 7: Machines à couper le verre feuilletéMachines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 7: Cutting machines for laminated glass81.100Equipment for the glass and ceramics industriesICS:Ta slovenski standard je istoveten z:EN 13035-7:2006+A1:2009SIST EN 13035-7:2007+A1:2010en,fr01-februar-2010SIST EN 13035-7:2007+A1:2010SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13035-7:2006+A1
December 2009 ICS 81.100 Supersedes EN 13035-7:2006English Version
Machines and plants for the manufacture, treatment and processing of flat glass - Safety requirements - Part 7: Cutting machines for laminated glass
Machines et installations pour la production, le façonnage et la transformation du verre plat - Exigences de sécurité - Partie 7: Machines à couper le verre feuilleté
Maschinen und Anlagen zur Herstellung, Be- und Verarbeitung von Flachglas - Sicherheitsanforderungen - Teil 7: Schneidmaschinen für Verbundglas This European Standard was approved by CEN on 24 May 2006 and includes Amendment 1 approved by CEN on 24 October 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13035-7:2006+A1:2009: ESIST EN 13035-7:2007+A1:2010

!!!!Noise-test code"""" . 13Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC . 15Annex ZB (informative)
!!!!Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC"""" . 16Bibliography . 17
Tables Table 1 — List of significant hazards . 8!Table 2 — Individual testing for requirements listed in Clause 5" . 10 SIST EN 13035-7:2007+A1:2010

1 Scope 1.1 This European Standard applies for cutting machines for laminated glass including the following steps: transport and positioning, synchronous cutting (scoring) from both sides, break-out, electrical heating and separation. 1.2 !This European Standard deals with the significant hazards, hazardous situations and events rele-vant to cutting machines for laminated glass when they are used as intended and under the conditions of mis-use which are reasonably foreseeable by the manufacturer (see Clause 4)." Those hazards, which are dealt with in the ad-hoc standard EN 619 for conveyors are excepted. !This European Standard specifies the ap-propriate technical measures to eliminate or reduce risks arising from the significant hazards during commis-sioning, operation and maintenance." Hazards from noise are not considered to be significant. 1.3 This European Standard is not applicable to cutting (scoring) and break-out of monolithic glass (see EN 13035-3 and EN 13035-6). 1.4 This European Standard is not applicable to the cutting of laminated glass by sawing or by the use of high-pressure liquid. 1.5 This European Standard is not applicable to the significant hazards of conveyors and machines for the manufacture, treatment and processing of flat glass such as tilting tables. 1.6 This European Standard is not applicable to cutting machines for laminated glass which are manufac-tured before the date of publication of this European Standard by CEN. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated refer-ences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 349:1993, Safety of machinery — Minimum gaps to avoid crushing of parts of the human body !deleted text" EN 953:1997, Safety of machinery — Guards — General requirements for the design and construction of fixed and movable guards !deleted text" EN 983:1996, Safety of machinery — Safety requirements for fluid power systems and their components — Pneumatics EN 1037:1995, Safety of machinery — Prevention of unexpected start-up !deleted text" EN 1760-2:2001, Safety of machinery — Pressure sensitive protective devices — Part 2: General principles for the design and testing of pressure sensitive edges and pressure sensitive bars !EN 60204-1:2006, Safety of machinery — Electrical equipment of machines — Part 1: General require-ments (IEC 60204-1:2005, modified) SIST EN 13035-7:2007+A1:2010

requirements and tests (IEC 61496-1:2004, modified) !deleted text" !EN ISO 4871:2009, Acoustics — Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) EN ISO 11201:2009, Acoustics — Noise emitted by machinery and equipment — Measurement of emission sound pressure levels at a work station and at other specified positions — Engineering method in an essen-tially free field over a reflecting plane (ISO 11201:1995, including Cor 1:1997) EN ISO 11202:2009, Acoustics — Noise emitted by machinery and equipment — Measurement of emission sound pressure levels at a work station and at other specified positions — Survey method in situ (ISO 11202:1995) EN ISO 11204:2009, Acoustics — Noise emitted by machinery and equipment — Measurement of emission sound pressure levels at a work station and at other specified positions — Method requiring environmental corrections (ISO 11204:1995, including Cor 1:1997)" EN ISO 12100-1:2003, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic terminology, methodology (ISO 12100-1:2003) EN ISO 12100-2:2003, Safety of machinery — Basic concepts, general principles for design — Part 2: Tech-nical principles (ISO 12100-2:2003) !EN ISO 13732-1:2008, Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces (ISO 13732-1:2006) EN ISO 13849-1:2008, Safety of machinery — Safety-related parts of control systems — Part 1: General prin-ciples for design (ISO 13849-1:2006) EN ISO 13850, Safety of machinery — Emergency stop — Principles for design (ISO 13850:2006) CLC/TS 61496-2:2006, Safety of machinery — Electro-sensitive protective equipment — Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs) (IEC 61496-2:2006)" 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 12100-1:2003 and the following apply: 3.1 laminated (glass) (flat) glass composed of layers of flat glass joined together by plastic layers 3.2 break-out method to open a cut (score) by generating strain, e.g. by mechanical devices 3.3 carriage mounting assembly for moving the cutting heads with the cutting tools in the axis of the (fixed) cutting bridge SIST EN 13035-7:2007+A1:2010
...