iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1487:2000

(Main)

Building valves - Hydraulic safety groups - Tests and requirements

Building valves - Hydraulic safety groups - Tests and requirements

This European Standard specifies, dimensions, materials and performance requirements (including methods of test) for hydraulic safety groups, of nominal sizes from DN 15 to DN 40, having working pressures from 0,1 MPa (1 bar) to 0,7 MPa ( 7 bar). Hydraulic safety groups are intended for fitting to the cold water supply of storage water heaters, having a maximum distribution temperature of 95°C,, for all energy sources.

Gebäudearmaturen - Hydraulische Sicherheitsgruppen - Prüfungen und Anforderungen

Diese Europäische Norm legt Maße, Werkstoffe und Leistungsanforderungen (einschließlich der Prüfverfahren) für hydraulische Sicherheitsgruppen in den Nennweiten DN 15 bis DN 40 mit Arbeitsdrücken) von 0,1 MPa (1 bar) bis 0,7 MPa (7 bar) fest. Hydraulische Sicherheitsgruppen sind für die Ausrüstung der Kaltwasserversorgung von Speicherwassererwärmern mit einer maximalen Gebrauchstemperatur von 95° C, unabhängig von den verwendeten Energiequellen bestimmt.

Robinetterie de bâtiment - Groupes de sécurité - Essais et prescriptions

La présente norme européenne spécifie les dimensions, la nature des matériaux et les exigences de performance (y compris les méthodes d'essai) auxquelles doivent satisfaire les groupes de sécurité hydraulique pour des dimensions nominales de DN 15 à DN 40 et avec des pressions de service de 0,1 MPa (1 bar) à 0,7 MPa (7 bar). Les groupes de sécurité hydraulique sont destinés à être montés au niveau de l'alimentation eau froide des chauffe-eau à accumulation, dont la température ne dépasse pas 95°C, quelque soit le mode d'énergie utilisé.

Ventili v stavbah - Varnostni bloki - Preskusi in zahteve

General Information

Status
Withdrawn
Publication Date
21-Mar-2000
Withdrawal Date
08-Jul-2014
ICS
91.140.60 - Water supply systems
Technical Committee
CEN/TC 164 - Water supply
Drafting Committee
CEN/TC 164/WG 14 - Valves and fitting for buildings and devices to prevent pollution by backflow
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
09-Jul-2014
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
93/38/EEC - Procurement procedures of entities operating in the water, energy, transport and telecommunications sectors
Mandate
M/EXP - Expected mandates in CPD field.
Ref Project
SIST EN 1487:2000 - Building valves - Hydraulic safety groups - Tests and requirements

Relations

Replaced By
EN 1487:2014 - Building valves - Hydraulic safety groups - Tests and requirements
Effective Date
11-Jul-2011

Buy Standard

EN 1487:2000EN 1487:2000
PreviousNext
Standard
EN 1487:2000
English language
23 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Ventili v stavbah - Varnostni bloki - Preskusi in zahteveGebäudearmaturen - Hydraulische Sicherheitsgruppen - Prüfungen und AnforderungenRobinetterie de bâtiment - Groupes de sécurité - Essais et prescriptionsBuilding valves - Hydraulic safety groups - Tests and requirements91.140.60Sistemi za oskrbo z vodoWater supply systemsICS:Ta slovenski standard je istoveten z:EN 1487:2000SIST EN 1487:2000en01-november-2000SIST EN
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 17821:2023(Main)
Building valves - Frost resistant taps for outdoor use (FRT) - General technical specification
SIST EN 17821:2023

This document specifies:
- general construction, performance and material requirements for Frost Resistant Taps for outdoor use (FRT), PN 10.
- the application in the potable water installation with a static pressure of maximum 1,0 MPa (10 bar) and a distribution temperature of maximum 25 °C (PWC).
FRT valves shall consist of the 3 areas shown in Figure 1.
The conditions of use are according to the following Table 1.
The requirements with regard to the potable water quality are specified in national regulations.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12729:2023(Main)
Devices to prevent pollution by backflow of potable water - Controllable backflow preventer with reduced pressure zone - Family B - Type A
SIST EN 12729:2023

This document specifies the field of application, the dimensional, the physico-chemical, the design, the hydraulic, the mechanical, and the acoustic characteristics of controllable backflow preventers with reduced pressure zone, Family B, Type A.
This document covers controllable backflow preventers of Family B, Type A, with reduced pressure zones, intended to prevent pollution of potable water by backflow, caused by backsiphonage or by backpressure.
It is applicable to controllable backflow preventers in denominations DN 6 up to DN 250.
It covers controllable backflow preventers of PN 10 that are capable of working without modification or adjustment:
- at any pressure, up to 1 MPa (10 bar);
- with any pressure variation, up to 1 MPa (10 bar);
- in permanent duty at a limited temperature of 65 °C and for maximum 1 h at 90 °C.
It specifies also the test methods and requirements for verifying their characteristics, the marking and the presentation at delivery.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1491:2022(Main)
Building valves - Expansion valves - Tests and requirements
SIST EN 1491:2022

This document specifies dimensions, materials and performance requirements (including methods of test) for expansion valves, of nominal sizes from DN 15 to DN 32, having working pressures ) from 0,1 MPa (l bar) to 1,0 MPa (10 bar).
Expansion valves are intended for fitting to the cold potable water supply of storage water heaters, having a maximum distribution temperature of 95 °C, for all energy sources.
Expansion valves do not control the temperature and alone do not constitute the protection required for storage water heaters. Expansion valves limit pressure, in the water heaters to what they are fitted, that is produced by thermal expansion of the water.
NOTE   The use of the device specified in this document does not override the need to use controls (e.g. thermostats and cut-outs) which act directly on the power sources of water heaters (for more information see Annex A).

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 17801:2022(Main)
Guidelines for water safety plan concept in buildings
SIST-TP CEN/TR 17801:2022

This document describes a method for the analysis, evaluation and management of risks that exist or may arise from the use of potable water installations within buildings and, for certain purposes, outside buildings but within the premises. Water Safety Plans for potable water supply systems are excluded from the scope of this document.
The document is addressed to all organisations and other stakeholders which are responsible for providing potable water within a safe potable water installation inside buildings according to EN 806, EN 1717 and national regulations.

  • Technical report
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1488:2021(Main)
Building valves - Expansion groups - Tests and requirements
SIST EN 1488:2021

This document specifies, dimensions, materials and performance requirements (including methods of test) for expansion groups, of nominal sizes from DN 15 to DN 25, having working pressures  from 0,1 MPa (1 bar) to 1,0 MPa (10 bar).
Expansion groups are fitted to the cold potable water supply only for expansion purposes, e.g. of storage water heaters, having a maximum distribution temperature of 95 °C.
Expansion groups limit pressure in the water heater to which they are fitted, that is produced by thermal expansion of the water, prevent the backflow of water into the supply pipe and prevent the discharged water to get into contact with the water in the water heater.
Expansion groups do not control temperature and alone do not constitute the protection required for storage water heaters.
NOTE   The use of the device specified in this document does not override the need to use controls (e.g. thermostats and thermal cut-outs) which act directly on the power sources of water heaters (for more information see Annex A).

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13618:2016(Main)
Flexible hose assemblies in drinking water installations - Functional requirements and test methods
SIST EN 13618:2017

This European Standard specifies the requirements and test methods for materials, dimensions and function for flexible hose assemblies for drinking water installations, braided or not, designed for use with drinking water with an allowable maximum operating pressure (PMA) of 1 MPa and maximum operating temperature 70 °C to connect sanitary tap ware, heaters and similar appliances.
NOTE   Flexible hose assemblies intended to be used as integral parts of electrical appliances are covered by EN 61770.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1487:2014(Main)
Building valves - Hydraulic safety groups - Tests and requirements
SIST EN 1487:2014

This European Standard specifies dimensions, materials and performance requirements (including methods of test) for hydraulic safety groups, of nominal sizes from DN 15 to DN 25, having working pressures ) from 0,1 MPa (1 bar) to 0,7 MPa (7 bar). Hydraulic safety groups are intended for fitting to the potable water supply of storage water heaters, having a maximum storage temperature of 95°C.
Hydraulic safety groups limit the pressure in hot water heaters, prevent the backflow of water into the main circuit and prevent the discharged water to get into contact with the water in the water heater.
Hydraulic safety groups do not control the temperature. They ensure the hydraulic safety of water heaters if the mechanical resistance of the water heater remains at least equal to the rating pressure.
NOTE   The use of the device specified in this European Standard does not override the need to use controls (e.g. thermostats and cut-outs) which act directly on the power sources of water heaters.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TR 16355:2012(Main)
Recommendations for prevention of Legionella growth in installations inside buildings conveying water for human consumption
SIST-TP CEN/TR 16355:2012

This Technical Report provides basic information about the conditions for Legionella growth in drinking water installations in accordance with EN 806 series up to draw-off points and gives recommendations for preventing the growth of Legionella in these installations.
NOTE 1   For further information, cf. Annex A.
NOTE 2   National documents regarding the prevention of Legionella growth are shown in Annex B.

  • Technical report
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 806-5:2012(Main)
Specifications for installations inside buildings conveying water for human consumption - Part 5: Operation and maintenance
SIST EN 806-5:2012

This European Standard specifies requirements and gives recommendations for the operation and maintenance of potable water installations within buildings and for pipework outside buildings but within the premises in accordance with EN 806-1.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 806-4:2010(Main)
Specifications for installations inside buildings conveying water for human consumption - Part 4: Installation
SIST EN 806-4:2011

This European Standard specifies requirements and gives recommendations for the installation of potable water installations within buildings and for pipework outside buildings but within the premises in accordance with EN 806-1. This European Standard is applicable to new installations, alterations and repairs.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day