Copper and copper alloys - Eddy current test for measuring defects on seamless round copper and copper alloy tubes - Part 2: Test with an internal probe on the inner surface

This document specifies a procedure for the eddy current test with an internal probe for measuring defects on the inner surface of seamless round copper and copper alloy tubes.
This document applies particularly for finned tubes with high fins according to EN 12452.
NOTE   The eddy current test method(s) required, together with the size range and acceptance level, are defined in the relevant product standard.
The choice of the method for eddy current test:
-   with an encircling test coil on the outer surface according to prEN 1971-1
or
-   with an internal probe on the inner surface according to prEN 1971-2
is at the discretion of the manufacturer if there are no other agreements between the purchaser and the supplier.
Especially for finned tubes according to EN 12452 with high fins, it is suggested to use eddy current test with internal probe as described in this document.

Kupfer und Kupferlegierungen - Wirbelstromprüfung an Rohren zur Messung von Fehlern an nahtlos gezogenen runden Rohren aus Kupfer und Kupferlegierungen - Teil 2: Prüfung mit Innensonde auf der Innenseite

Dieses Dokument legt ein Verfahren für die Wirbelstromprüfung mit Innensonde zur Messung von Fehlern auf der Innenoberfläche von nahtlosen Rundrohren aus Kupfer und Kupferlegierungen fest.
Dieses Dokument ist insbesondere für Rippenrohre mit hohen Rippen nach EN 12452 anwendbar.
ANMERKUNG Das (Die) geforderte(n) Wirbelstromprüfverfahren sowie der Maßbereich und die Sortiergrenze sind in der entsprechenden Produktnorm festgelegt.
Die Wahl des Verfahrens für die Wirbelstromprüfung mit
- umfassender Spule auf der Außenseite nach EN 1971-1
oder
- Innensonde auf der Innenseite nach EN 1971-2
obliegt dem Hersteller, wenn keine anderen Vereinbarungen zwischen Hersteller und Lieferer getroffen wurden.
Besonders für Rippenrohre mit hohen Rippen nach EN 12452 wird die Anwendung der Wirbelstromprüfung mit Innensonde, wie in diesem Dokument beschrieben, empfohlen.

Cuivre et alliages de cuivre - Méthode de contrôle par courants de Foucault pour le mesurage des défauts des tubes ronds sans soudure en cuivre et alliages de cuivre - Partie 2 : Essai avec un capteur interne sur la paroi interne

Le présent document spécifie un mode opératoire relatif au contrôle par courants de Foucault pour le mesurage des défauts présents sur la paroi interne des tubes ronds sans soudure en cuivre et alliages de cuivre, au moyen d’un capteur interne.
Le présent document s'applique en particulier aux tubes à ailettes avec ailettes hautes selon l'EN 12452.
NOTE   La ou les méthodes de contrôle par courants de Foucault requises, ainsi que les gammes de dimensions concernées et le niveau d'acceptation, sont spécifiés dans la norme de produit correspondante.
Le choix de la méthode de contrôle par courants de Foucault :
-   avec une bobine encerclante sur la paroi externe selon le prEN 1971-1 ;
ou
-   avec un capteur interne sur la paroi interne selon le prEN 1971-2 ;
est laissé à la discrétion du fabricant, sauf accord contraire entre le client et le fournisseur.
Il est suggéré, en particulier pour les tubes à ailettes selon l’EN 12452 avec ailettes hautes, d’utiliser le contrôle par courants de Foucault avec capteur interne selon la description du présent document.

Baker in bakrove zlitine - Metoda preskušanja z vrtinčnimi tokovi za merjenje napak na nevarjenih okroglih ceveh iz bakra in bakrovih zlitin - 2. del: Preskus z notranjo preskusno tuljavo ob notranji površini

Ta dokument določa postopek za metodo preskušanja z vrtinčnimi tokovi z notranjo preskusno tuljavo za merjenje napak ob notranji površini nevarjenih okroglih cevi iz bakra in bakrovih zlitin. Ta dokument se uporablja še posebej za narebričene cevi z visokimi rebri v skladu s standardom EN 12452.
OPOMBA: Zahtevane metode preskušanja z vrtinčnimi tokovi ter razpon velikosti in meja sprejemljivosti so določeni v ustreznem standardu za izdelek.
Metodo za preskušanje z vrtinčnimi tokovi:
– s preskusno tuljavo, ki obdaja zunanjo površino, v skladu s standardom prEN 1971-1; ali
– z notranjo tuljavo ob notranji površini v skladu s standardom prEN 1971-2;
izbere proizvajalec, če ne obstaja drugačen dogovor med kupcem in dobaviteljem.
Preskušanje z vrtinčnimi tokovi z notranjo preskusno tuljavo v skladu s tem dokumentom je predlagano zlasti za narebričene cevi v skladu s standardom EN 12452 z visokimi rebri.

General Information

Status
Published
Publication Date
19-Nov-2019
Withdrawal Date
30-May-2020
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
20-Nov-2019
Due Date
26-Jan-2021
Completion Date
20-Nov-2019

Relations

Buy Standard

Standard
EN 1971-2:2020
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 1971-2:2019
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 1971-2:2020
01-januar-2020
Nadomešča:
SIST EN 1971-2:2012
Baker in bakrove zlitine - Metoda preskušanja z vrtinčnimi tokovi za merjenje
napak na nevarjenih okroglih ceveh iz bakra in bakrovih zlitin - 2. del: Preskus z
notranjo preskusno tuljavo ob notranji površini
Copper and copper alloys - Eddy current test for measuring defects on seamless round
copper and copper alloy tubes - Part 2: Test with an internal probe on the inner surface
Kupfer und Kupferlegierungen - Wirbelstromprüfung an Rohren zur Messung von
Fehlern an nahtlos gezogenen runden Rohren aus Kupfer und Kupferlegierungen - Teil
2: Prüfung mit Innensonde auf der Innenseite
Cuivre et alliages de cuivre - Méthode de contrôle par courants de Foucault pour le
mesurage des défauts des tubes ronds sans soudure en cuivre et alliages de cuivre -
Partie 2 : Essai avec un capteur interne sur la paroi interne
Ta slovenski standard je istoveten z: EN 1971-2:2019
ICS:
23.040.15 Cevi iz neželeznih kovin Non-ferrous metal pipes
77.150.30 Bakreni izdelki Copper products
SIST EN 1971-2:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 1971-2:2020

---------------------- Page: 2 ----------------------
SIST EN 1971-2:2020


EN 1971-2
EUROPEAN STANDARD

NORME EUROPÉENNE

November 2019
EUROPÄISCHE NORM
ICS 23.040.15; 77.150.30 Supersedes EN 1971-2:2011
English Version

Copper and copper alloys - Eddy current test for
measuring defects on seamless round copper and copper
alloy tubes - Part 2: Test with an internal probe on the
inner surface
Cuivre et alliages de cuivre - Méthode de contrôle par Kupfer und Kupferlegierungen - Wirbelstromprüfung
courants de Foucault pour le mesurage des défauts des an Rohren zur Messung von Fehlern an nahtlos
tubes ronds sans soudure en cuivre et alliages de gezogenen runden Rohren aus Kupfer und
cuivre - Partie 2 : Essai avec un capteur interne sur la Kupferlegierungen - Teil 2: Prüfung mit Innensonde auf
paroi interne der Innenseite
This European Standard was approved by CEN on 4 September 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1971-2:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 1971-2:2020
EN 1971-2:2019 (E)
Contents Page

European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 General requirements . 5
4.1 Personnel qualification . 5
4.2 Condition of tube to be tested .
...

SLOVENSKI STANDARD
oSIST prEN 1971-2:2019
01-april-2019
%DNHULQEDNURYH]OLWLQH0HWRGDSUHVNXãDQMD]YUWLQþQLPLWRNRYL]DPHUMHQMH
QDSDNQDQHYDUMHQLKRNURJOLKFHYHKL]EDNUDLQEDNURYLK]OLWLQGHO3UHVNXV]
QRWUDQMRSUHVNXVQRWXOMDYRREQRWUDQMLSRYUãLQL
Copper and copper alloys - Eddy current test for measuring defects on seamless round
copper and copper alloy tubes - Part 2: Test with an internal probe on the inner surface
Kupfer und Kupferlegierungen - Wirbelstromprüfung an Rohren zur Messung von
Fehlern an nahtlos gezogenen runden Rohren aus Kupfer und Kupferlegierungen - Teil
2: Prüfung mit Innensonde auf der Innenseite
Cuivre et alliages de cuivre - Méthode de contrôle par courants de Foucault pour le
mesurage des défauts des tubes ronds sans soudure en cuivre et alliages de cuivre -
Partie 2 : Essai avec un capteur interne sur la paroi interne
Ta slovenski standard je istoveten z: prEN 1971-2
ICS:
23.040.15 Cevi iz neželeznih kovin Non-ferrous metal pipes
77.150.30 Bakreni izdelki Copper products
oSIST prEN 1971-2:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 1971-2:2019

---------------------- Page: 2 ----------------------
oSIST prEN 1971-2:2019


DRAFT
EUROPEAN STANDARD
prEN 1971-2
NORME EUROPÉENNE

EUROPÄISCHE NORM

February 2019
ICS 23.040.15; 77.150.30 Will supersede EN 1971-2:2011
English Version

Copper and copper alloys - Eddy current test for
measuring defects on seamless round copper and copper
alloy tubes - Part 2: Test with an internal probe on the
inner surface
Cuivre et alliages de cuivre - Méthode de contrôle par Kupfer und Kupferlegierungen - Wirbelstromprüfung
courants de Foucault pour le mesurage des défauts des an Rohren zur Messung von Fehlern an nahtlos
tubes ronds sans soudure en cuivre et alliages de gezogenen runden Rohren aus Kupfer und
cuivre - Partie 2 : Essai avec un capteur interne sur la Kupferlegierungen - Teil 2: Prüfung mit Innensonde auf
paroi interne der Innenseite
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 133.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1971-2:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 1971-2:2019
prEN 1971-2:2019 (E)
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 General requirements .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.