Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification

This European Standard specifies minimum requirements for three types of hoses in two categories and two classes of hose assemblies used for measured fuel dispensing, including oxygenated fuels (up to a maximum of 15 % oxygenated compounds).
The assemblies are intended for use at ambient temperatures between -30 °C and +55 °C for normal temperature class and -40 °C and +55 °C for low temperature class at a working pressure £ 16 bar ) .

Zapfstellenschläuche und -schlauchleitungen aus Gummi und Kunststoff - Anforderungen

Diese Europäische Norm legt für drei Typen von Zapfstellenschläuchen für Kraftstoffe, die in zwei Kategorien
und zwei Klassen  unterteilt  werden, die Mindestanforderungen fest, wobei mit sauerstoffhaltigen
Verbindungen  angereicherte  Kraftstoffe (bis  zu einem maximalen Anteil  von 15 %  sauerstoffhaltigen
Verbindungen) einbezogen sind.
Die Anwendung  von Schlauchleitungen der  Normaltemperaturklasse  ist bei Umgebungstemperaturen
zwischen  . 30 °C  bis  + 55 °C  und  von  Schlauchleitungen der Tieftemperaturklasse zwischen  . 40 °C  und
+ 55 °C bei einem Arbeitsdruck von 16 bar1) vorgesehen.

Tuyaux et flexibles en caoutchouc pour distribution mesurée de carburants - Spécification

La présente Norme européenne spécifie les exigences minimales pour trois types de tuyaux dans deux
catégories et deux classes de flexibles utilisés pour la distribution mesurée des carburants, y compris les
carburants oxygénés (comprenant jusqu�à 15 % maximum de composants oxygénés).
Les flexibles sont destinés à être utilisés à température ambiante comprise entre - 30 °C et + 55 °C pour une
classe de température normale et - 40 °C à + 55 °C pour la classe basse température à une pression de
travail £ 16 bar1).

Gumene in polimerne cevi in cevni priključki za merjeno točenje goriv - Specifikacija

General Information

Status
Withdrawn
Publication Date
03-May-2005
Withdrawal Date
18-Jun-2013
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
19-Jun-2013
Completion Date
19-Jun-2013

Relations

Buy Standard

Standard
EN 1360:2005
English language
28 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.6SHFLILNDFLMDZapfstellenschläuche und -schlauchleitungen aus Gummi und Kunststoff - AnforderungenTuyaux et flexibles en caoutchouc pour distribution mesurée de carburants - SpécificationRubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification83.140.40Gumene ceviHoses75.200Petroleum products and natural gas handling equipmentICS:Ta slovenski standard je istoveten z:EN 1360:2005SIST EN 1360:2005en01-julij-2005SIST EN 1360:2005SLOVENSKI
STANDARDSIST EN 1360:20001DGRPHãþD



SIST EN 1360:2005



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1360
May 2005 ICS 75.200; 23.040.70
Supersedes EN 1360:1996
English version
Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification
Tuyaux et flexibles en caoutchouc pour distribution mesurée de carburants - Spécification
Zapfstellenschläuche und -schlauchleitungen aus Gummi und Kunststoff - Anforderungen This European Standard was approved by CEN on 15 March 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2005 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1360:2005: ESIST EN 1360:2005



EN 1360:2005 (E) 2 Contents page Foreword.4 1 Scope.5 2 Normative references.5 3 Terms and definitions.6 4 Classification.6 5 Materials and construction.6 6 Pressure requirements.6 7 Dimensions and tolerances.7 7.1 Internal diameters and bend radii.7 7.2 Minimum thickness of lining and cover.7 7.3 Concentricity.7 7.4 Tolerance on cut lengths.7 8 Physical properties.7 8.1 Compounds.7 8.2 Finished hose.9 8.3 Hose assembly.10 9 End fittings.10 10 T
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.