FprEN 13631-5
(Main)Explosives for civil uses - Explosives for blasting, boosters and explosive substances - Part 5: Verification of the resistance to water of explosives for blasting and boosters
Explosives for civil uses - Explosives for blasting, boosters and explosive substances - Part 5: Verification of the resistance to water of explosives for blasting and boosters
This European Standard specifies a method of determining the resistance to water of cartridged or bulk high explosives for civil uses, which are designed to be used for blasting operations in wet conditions.
Explosivstoffe für zivile Zwecke - Explosivstoffe - Teil 5: Bestimmung der Wasserfestigkeit von Explosivstoffen
Explosifs à usage civil - Explosifs - Partie 5 : Détermination de la résistance à l'eau
Eksplozivi za civilno uporabo – Razstreliva – 5. del: Ugotavljanje odpornosti proti vodi
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2021
Eksplozivi za civilno uporabo – Razstreliva – 5. del: Ugotavljanje odpornosti proti
vodi
Explosives for civil uses - High explosives - Part 5: Determination of resistance to water
Explosivstoffe für zivile Zwecke - Sprengstoffe - Teil 5: Bestimmung der Wasserfestigkeit
Installation solaires thermiques et leur composants - Installations préfabriquées en usine
- Partie 1 : Exigence générale
Ta slovenski standard je istoveten z: prEN 13631-5
ICS:
71.100.30 Eksplozivi. Pirotehnika in Explosives. Pyrotechnics and
ognjemeti fireworks
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
prEN 13631-5
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2021
ICS 71.100.30 Will supersede EN 13631-5:2002
English Version
Explosives for civil uses - Explosives - Part 5:
Determination of the resistance to water of explosives
IExplosifs à usage civil - Explosifs - Partie 5 : Explosivstoffe für zivile Zwecke - Explosivstoffe - Teil
Détermination de la résistance à l'eau 5: Bestimmung der Wasserfestigkeit von
Explosivstoffen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 321.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13631-5:2021 E
worldwide for CEN national Members.
prEN 13631-5:2021 (E)
Contents Page
European foreword . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle . 5
5 Apparatus . 5
6 Test pieces . 7
6.1 Cartridged Explosives . 7
6.2 Bulk explosive . 7
6.3 Cutting notches . 7
7 Procedure . 8
7.1 Preliminary test for cartridged explosives. 8
7.2 Test set-up and testing of cartridges explosives . 8
7.3 Bulk explosives . 9
7.4 Alternative test method . 9
7.5 Assessment criteria . 10
8 Test report . 10
Annex ZA (informative) Relationship between this European Standard and the essential
safety requirements of Directive 2014/28/EU relating to the making available on
the market and supervision of explosives for civil uses aimed to be covered . 11
Bibliography . 12
prEN 13631-5:2021 (E)
European foreword
This document (prEN 13631-5:2021) has been prepared by Technical Committee CEN/TC 321
“Explosives for civil uses”, the secretariat of which is held by UNE.
This document is currently submitted for the CEN Enquiry.
This document will supersede EN 13631-5:2002.
In comparison with the previous edition, the following technical modifications have been made:
a) the main element of the document’s title has been changed from “High explosives” to “Explosives”;
b) the normative references have been updated;
c) a new method for measuring the velocity of detonation by means of a continuous wire probe has
been added;
d) the description of the preparatory steps and for performing the test have been clearly separated;
e) the concept of “water resistance” has been clarified by addressing with this part only shallow water
up to a water depth of 20 cm, including general humidity and spray water;
f) Annex A, Range of applicability of the test method, has been removed;
g) Annex ZA has been updated.
This document has been prepared under a Standardization Request (M/562) annexed to the
Commission Implementing Decision C(2019)6634 final as regards Explosives for civil uses given to CEN
by the European Commission and the European Free Trade Association, and supports Essential Safety
requirements of Directive 2014/28/EU.
For relationship with Directive 2014/28/EU, see informative Annex ZA, which is an integral part of this
document.
EN 13631, Explosives for civil uses — Explosives, is currently composed with the following parts:
— Part 1: Requirements
— Part 2: Determination of thermal stability of explosives
— Part 3: Determination of sensitiveness to friction of explosives
— Part 4: Determination of sensitiveness to impact of explosives
— Part 5: Determination of resistance of explosives to water
— Part 6: Determination of resistance of explosives to hydrostatic pressure
— Part 7: Determination of safety and reliability of explosives at extreme temperatures
— Part 10: Method for the verification of the means of initiation of explosives
prEN 13631-5:2021 (E)
— Part 11: Determination of transmission of detonation of explosives
— Part 13: Determination of density of explosives
— Part 14: Determination of velocity of detonation of explosives
prEN 13631-5:2021 (E)
1 Scope
This document specifies a test method of determining the resistance to water of boosters, cartridge or
bulk explosives, which are designed to be used for blasting operations in wet conditions.
This test method does not apply to black powder.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
prEN 13630-7:2021, Explosives for civil uses - Detonating cords and safety fuses - Part 7: Determination of
reliability of initiation of detonating cords
prEN 13631-14:2021, Explosives for civil uses — Explosives — Part 14: Determination of the velocity of
detonation of explosives
prEN 13857-1:2021, Explosives for civil uses — Part 1: Terminology
3 Terms and definitions
For the purposes of this document, the terms and definitions given in prEN 13857-1:2021 apply.
4 Principle
The test method addresses potential negative effects of water penetration into the explosive.
The testing distinguishes between explosives, where a cover material (in case of cartridged explosives)
is necessary to guarantee water resistance and other explosives, which are water resistant even without
the cover material. In the latter case the cover material is cut prior to testing, in order to enable contact
of the explosive with the water.
NOTE 1 Knowledge on water resistance is necessary to guarantee reliable functioning, if the manufacturer
foresees use under wet conditions.
NOTE 2 The test does not address the ability of explosives to detonate under applied hydrostatic pressure.
5 Apparatus
5.1 V-shaped guide, made from aluminium or similar material, of length at least 500 mm longer than
the length of the cartridge under test (see Figure 1). The guide shall have a series of holes, spaced 2 mm
apart in the direction at right angles
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.