EN 14844:2006/prA1

Precast concrete products - Box culverts

A series of modifications regarding production tolerances.

Betonfertigteile - Hohlkastenelemente

Diese Europäische Norm wurde im Rahmen des Mandats M/100 Vorgefertigte Betonerzeugnisse"  ), das dem CEN von der Europäischen Kommission und der Europäischen Freihandelszone erteilt wurde, erarbeitet.
Die in diesem Anhang aufgeführten Abschnitte dieser Europäischen Norm erfüllen die Anforderungen des Mandats, das auf der Grundlage der EG-Bauproduktenrichtlinie (89/106/EWG) erteilt wurde.
Die Übereinstimmung mit diesen Abschnitten berechtigt zur Annahme, dass die Hohlkastenelemente, für die dieser Anhang gilt, für die hierin aufgeführten Verwendungszwecke geeignet sind. Die Angaben in den Begleitinformationen zum CE-Zeichen sind zu beachten.
WARNVERMERK - Für die Hohlkastenelemente, die unter den Anwendungsbereich dieser Norm fallen, können andere Anforderungen und andere EG-Richtlinien, die die Eignung für den vorgesehenen Verwendungszweck nicht beeinflussen, gelten.
ANMERKUNG 1   Für Produkte, die in den Anwendungsbereich dieser Norm fallen, können zusätzlich zu den in dieser Europäischen Norm enthaltenen speziellen Abschnitten über gefährliche Stoffe weitere Anforderungen gelten (z. B. umgesetzte europäische Gesetzesvorschriften sowie nationale Gesetze, Bestimmungen und Verwaltungsvorgaben). Um die Vorgaben der EG Bauproduktenrichtlinie zu erfüllen, müssen auch diese Anforderungen, wo immer sie anwendbar sind, erfüllt werden.
ANMERKUNG 2   Eine informative Datenbank europäischer und nationaler Vorschriften zu gefährlichen Stoffen steht auf der Bauprodukten-Website EUROPA zur Verfügung (Zugang über http://ec.europa.eu/enterprise/construction/internal/dangsub/dangmain_en.htm ).
Dieser Anhang legt die Bedingungen für die CE Kennzeichnung von Hohlkastenelementen aus Stahlbeton zur Herstellung von unterirdischen Hohlräumen fest, die für Transport und Lagerung vorgesehen sind, und führt die zutreffenden anwendbaren Abschnitte auf.
Dieser Anhang hat denselben Anwendungsbereich wie Abschnitt 1 dieser Europäischen Norm und wird durch Tabelle ZA.1 definiert.

Produits préfabriqués en béton - Cadres enterrés

Montažni betonski izdelki - Škatlasti nosilci

General Information

• Status: Not Published
• ICS: 91.100.30 - Concrete and concrete products
• Technical Committee: CEN/TC 229 - Precast concrete products
• Drafting Committee: CEN/TC 229/WG 1 - Products for which the stability requirements is predominant
• Current Stage: 5060 - Closure of Vote - Formal Approval
• Start Date: 21-Jul-2008
• Due Date: 29-Aug-2008
• Completion Date: 21-Jul-2008
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Mandate: M/100 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on precast concrete products
• Ref Project: SIST EN 14844:2006/kprA1:2008 - Precast concrete products - Box culverts

Relations

• Merged Into: EN 14844:2006+A1:2008 - Precast concrete products - Box culverts
• Effective Date: 19-Jan-2023
• Amends: EN 14844:2006 - Precast concrete products - Box culverts
• Effective Date: 22-Dec-2008

Standards Content (Sample)

SLOVENSKI STANDARD
01-maj-2008
Montažni betonski izdelki - Škatlasti nosilci
Precast concrete products - Box culverts
Betonfertigteile - Hohlkastenelemente
Produits préfabriqués en béton - Cadres enterrés
Ta slovenski standard je istoveten z: EN 14844:2006/prA1
ICS:
91.100.30
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
FINAL DRAFT
EN 14844:2006
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
February 2008
ICS 91.100.30
English Version
Precast concrete products - Box culverts
Produits préfabriqués en béton - Cadres enterrés Betonfertigteile - Hohlkastenelemente
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 229.
This draft amendment A1, if approved, will modify the European Standard EN 14844:2006. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14844:2006/prA1:2008: E
worldwide for CEN national Members.

Foreword
This document (EN 14844:2007/prA1:2008) has been prepared by Technical Committee CEN/TC 229
“Precast concrete products”, the secretariat of which is held by AFNOR.
This document is currently submitted to the Unique Acceptance Procedure.

1 Modification to Foreword
th
In the 9 paragraph, replace
"prEN 14843" with "EN 14843",
"prEN 14991" with "EN 14991",
"prEN 14992" with "EN 14992" and
"prEN 15050" with "EN 15050".
2 Modification to 4.3.1.1, Production tolerances
rd
In the 3 paragraph, delete the sentence "The length of the nib should normally be in the range from 1.3 to 2
times the nib root dimension.".
rd
After the 3 paragraph add the following Note:
"NOTE It is suitable that, except for dimensions close to the minimum specified hereafter, the length d of the nib
should be in the range from 1,3 to 2 times the nib root dimension a + b.".
th
In the 4 paragraph
nd
 in the 2 indent replace "(max 15 mm)" with "(min. -10, max. + 15 mm)";
rd
 in the 3 indent add "(min. ± 15 mm)" after "± 1 %";
th
 in the 4 indent replace "± 6 mm" with "± 10 mm".
3 Modification to Annex ZA, Relationship between this European Standard and the
essential requirements of EC Directive 89/106/EEC, Construction Products Directive
Replace the whole Annex ZA with the following new text: "
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of EU Directive 89/106/EEC, EU Construction Products
Directive
ZA.1 Scope and relevant characteristics
This European Standard has been prepared under the mandate M/100 "Precast Concrete Products" given to
CEN by the European Commission and the European Free Trade Association.
The clauses of this European Standard shown in this annex meet the requirements of the mandate given
under the EU Construction Products Directive (89/106/EEC).
Compliance with these clauses confers a presumption of fitness of the box culvert units covered by this Annex
for the intended uses indicated herein; reference shall be made to the information accompanying the CE
marking.
WARNING — Other requirements and other EU Directives, not affecting the fitness for intended uses, may be
applicable to the box culverts falling within the scope of this standard.
NOTE 1 In addition to any specific clauses relating to dangerous substances contained in this European Standard,
there may be requirements applicable to the products falling within its scope (e.g. transposed European legislation and
national laws, regulations and administrative provisions). In order to meet the provisions of the EU Construction
Products Directive, these requirements need also to be complied with, when and where they apply.
NOTE 2 An informative database of European and national provisions on dangerous substances is available at the
Construction web site on EUROPA (accessed through
http://ec.europa.eu/enterprise/construction/internal/dangsub/dangmain_en.htm ).
This annex establishes the conditions for the CE marking of the box culvert units of reinforced concrete used
for the creation of voids below ground for the purposes of conveyance or storage and shows the relevant
clauses applicable.
This annex has the same scope as Clause 1 of this European Standard and is defined by Table ZA.1.

As amended
Table ZA.1 — Clauses of this European Standard addressing the provisions of the EU Construction
Products Directive
Levels
Requirement clauses in this European
Essential characteristics and/or Notes and unit
Standard
class(es)
Compressive strength (of 2
All methods 4.2 Production requirements None N/mm
concrete)
4.1.3 Reinforcing steel
Ultimate tensile and tensile
All methods 4.1.4 Prestressing steel None N/mm
yield strength (of steel)
of EN 13369:2004
Geometry and
Method 1 Information listed in ZA.3.2 None
materials
Load bearing capacity (by
tests) or mechanical
Method 2 4.3.3 Mechanical resistance None kNm, kN, kN/m
strength (by calculation)
Method 3 4.3.3 Mechanical resistance None Design
specification
4.3.1 Geometrical properties mm
Detailing All methods None
8 Technical documentation
Durability against corrosion All methods 4.3.7 Durability None Ambient
conditions
Durability against freeze-
Exposure
thaw (for exposed All methods 4.3.7 Durability None
classes
applications)
Drying shrinkage (in end
use conditions and only for All methods 4.2.2.3 Drying shrinkage None mm/m
lightweight concrete)
The manufacturer or his authorized representative in the EEA shall select for CE marking the declaration
method(s) he applies among the followings:
Method 1 = declaration of geometrical data and material properties (see ZA.3.2);
Method 2 = declaration of geometry, material properties and product properties determined following this
standard and EN Eurocodes (see ZA.3.3);
Method 3 = declaration of product compliance with a given design specification distinguishing:
Method 3a = declaration of product compliance with a given design specification provided by the client
(ZA.3.4);
Method 3b = declaration of product compliance with a given design specification provided by the manufacturer
according to the client's order (ZA.3.5).
The requirement on a certain characteristic is not applicable in those Member States (MSs) where there are
no regulatory requirements for that characteristic for the intended use of the product. In this case,
manufacturers placing their products on the market of these MSs are not obliged to determine nor to declare
the performance of their products with regard to this characteristic and the option “No performance
determined” (NPD) in the information accompanying the CE marking (see ZA.3) may be used. The NPD
option may not be used, however, where the characteristic is subject to a threshold level.
ZA.2 Procedure(s) for the attestation of conformity of box culvert units
ZA.2.1 Systems of attestation of conformity
The systems of attestation of conformity of the box culvert units, for the essential characteristics indicated in
Table ZA.1, in accordance with the Decision of the Commission 1999/94/EC of 25 January 1999 as given in
Annex III of the Mandate M/100 "Precast concrete products", is shown in Table ZA.2 for the indicated intended
uses and relevant levels or classes:
Table ZA.2 — Systems of attestation of conformity
Attestation of conformity
Products Intended uses Levels or classes
systems
Large box culverts structural – 2+
non-structural or light
Small box culverts – 4
structural
System 2+: see Directive 89/106 (CPD), annex III.2.(ii), First possibility, including certification of the factory
production control by an approved body on the basis of initial inspection of factory and of factory production control
as well as of continuous surveillance, assessment and approval of factory production control.
System 4: see Directive 89/106 (CPD), annex III.2.(ii), Third possibility.
The attestation of conformity of the box culvert units for the essential characteristics indicated in Table ZA.1
shall be based on the evaluation of conformity procedures indicated in Tables ZA.3a and ZA.3b resulting from
application of the clauses of this or other European Standard indicated therein.
Table ZA.3a — Assignment of evaluation of conformity tasks for box culverts under system 2++++
Evaluation of conformity
Tasks Content of the tasks
clauses to apply
a
All characteristics of Table ZA.1 6.2
Initial type testing
Tasks under the
Parameters related to all
Factory production control 6.3
responsibility of the
characteristics of Table ZA.1
manufacturer
Further testing of samples
All characteristics of Table ZA.1 6.2.3
taken at the factory
 Compressive strength (of
concrete);
 Ultimate tensile and tensile
yield strength;
Initial inspection of factory
c
 Mechanical resistance
and of factory production 6.3
b
control
 Detailing;
 Durability;
Tasks
 Load bearing capacity
Certification of
under the
factory (when verified by testing).
responsibi-
production
lity of the
 Compressive strength (of
control on the
notified
concrete);
basis of:
body
 Ultimate tensile and tensile
yield strength;
Continuous surveillance,
c
assessments and approval  Mechanical resistance
6.3
of factory production
 Detailing;
control
 Durability;
 Load bearing capacity
(when verified by testing).
a
Initial Type Testing (ITT) includes calculation and/or testing. ITT by calculation is not required when only methods 1 and 3a are used.
b
Includes assessment that the factory production control system contains documented procedures related to ITT (calculation and/or
testing) and that these procedures are followed. Reference to ITT of mechanical resistance can be omitted when only methods 1 and
3a are used.
c
Only for methods 2 and 3b.
Table ZA.3b — Assignment of evaluation of conformity tasks for box culverts under system 4
Evaluation of conformity
Tasks Content of the tasks
clauses to apply
All characteristics of
a
6.2
Initial type testing
Table ZA.1
Tasks for the
manufacturer
Parameters related to all
Factory production control 6.3
characteristics of Table ZA.1
a
Initial Type Testing (ITT) includes calculation and/or testing. ITT by calculation is not required when only methods 1 and 3a are used.
ZA.2.2 EC Certificate and Declaration of conformity
Large box culverts under system 2++++: When compliance with the conditions of this annex is achieved, and
once the notified body has drawn up the certificate mentioned below, the manufacturer or his agent
established in the EEA shall prepare and retain a declaration of conformity, which entitles the manufacturer to
affix the CE marking. This declaration shall include:
 name and address of the manufacturer, or his authorised representative established in the EEA, and the
place of production;
NOTE 1 The manufacturer may also be the person responsible for placing the product onto the EEA market, if he
takes responsibility for CE marking.
 description of the product (type, identification, use etc.), and a copy of the information accompanying the
CE marking;
NOTE 2 Where some of the information required for the Declaration is already given in the CE marking information,
it does not need to be repeated
 provisions to which the product conforms (e.g. Annex ZA of this EN);
 particular conditions applicable to the use of the product (e.g. provisions for use under certain conditions
etc.);
 the number of the accompanying factory production control certificate;
 name of, and position held by, the person empowered to sign the declaration on behalf of the
manufacturer or his authorised representative.
The declaration shall be accompanied by a factory production control certificate, drawn up by the notified
body, which shall contain, in addition to the information above, the following:
 name and address of the notified body;
 name and address of the manufacturer;
 the number of the factory production control certificate;
 conditions and period of validity of the certificate, where applicable;
 name of, and position held by, the person empowered to sign the certificate;
 identification of the products covered by the Factory Production Control Certificate and for each product,
identification of:
 the method(s) of CE marking applied by the manufacturer;
 whether the product is reinforced or not;
 other distinguished product families as identified in 6.2.1 or by the manufacturer himself and
affect the content and/or procedures of the factory production control including the
procedure of type testing.
Small box culverts under system 4: When compliance with the conditions of this annex is achieved, the
manufacturer or his agent established in the EEA shall prepare and retain a declarati
...