iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

CEN/TR 15124:2005

(Main)

Design, preparation and application of internal gypsum plastering systems

Design, preparation and application of internal gypsum plastering systems

This document concerns the design, preparation and application of plaster based on gypsum, for internal plastering on all types of background used under normal conditions. It includes plastering onto both new and old backgrounds and the maintenance and repair of existing work. It concerns materials, backgrounds, preparation of the surface to be plastered, choice of suitable gypsum plastering system, methods of application and inspection and testing of plastering.
Gypsum plastering mixes with special properties intended to enhance thermal insulation, fire resistance, acoustic insulation and to increase radiation absorption are also covered.
Because of the many and varied materials and practices in Europe it is not possible for certain aspects of the standard to enter into sufficient detail to be fully usable to practitioners in each country.

Planung, Zubereitung und Ausführung von Gips-Innenputzsystemen

Načrtovanje, priprava in uporaba notranjih mavčnih ometov

General Information

Status
Withdrawn
Publication Date
14-Jun-2005
Withdrawal Date
04-Sep-2023
ICS
91.100.10 - Cement. Gypsum. Lime. Mortar
91.180 - Interior finishing
Technical Committee
CEN/TC 125 - Masonry
Drafting Committee
CEN/TC 125/WG 5 - Application of external rendering in masonry
Current Stage
Ref Project
SIST-TP CEN/TR 15124:2005 - Design, preparation and application of internal gypsum plastering systems

Buy Standard

TP CEN/TR 15124:2005TP CEN/TR 15124:2005
PreviousNext
Technical report
TP CEN/TR 15124:2005
English language
19 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST-TP CEN/TR 15124:2005
01-september-2005
1DþUWRYDQMHSULSUDYDLQXSRUDEDQRWUDQMLKPDYþQLKRPHWRY
Design, preparation and application of internal gypsum plastering systems
Planung, Zubereitung und Ausführung von Gips-Innenputzsystemen
Ta slovenski standard je istoveten z: CEN/TR 15124:2005
ICS:
91.100.10 Cement. Mavec. Apno. Malta Cement. Gypsum. Lime.
Mortar
91.180 1RWUDQMD]DNOMXþQDGHOD Interior finishing
SIST-TP CEN/TR 15124:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST-TP CEN/TR 15124:2005

---------------------- Page: 2 ----------------------

SIST-TP CEN/TR 15124:2005
TECHNICAL REPORT
CEN/TR 15124
RAPPORT TECHNIQUE
TECHNISCHER BERICHT
June 2005
ICS 91.100.10; 91.180
English version
Design, preparation and application of internal gypsum
plastering systems
Planung, Zubereitung und Ausführung von
Gipsinnenputzsystemen
This Technical Report was approved by CEN on 13 May 2005. It has been drawn up by the Technical Committee CEN/TC 125.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TR 15124:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST-TP CEN/TR 15124:2005
CEN/TR 15124:2005 (E)
Contents
Page
Foreword. 3
1 Scope. 4
2 Terms and definitions . 4
3 Materials and accessories . 5
4 Design - factors influencing the selection of gypsum plastering systems. 6
5 Characteristics of gypsum plastering systems.8
6 Types and standards of plaster finish . 13
7 Application. 14
Annex A (informative) Fixing applied backgrounds . 16
Bibliography . 19


2

---------------------- Page: 4 ----------------------

SIST-TP CEN/TR 15124:2005
CEN/TR 15124:2005 (E)
Foreword
This document (CEN/TR 15124:2005) has been prepared by Technical Committee CEN/TC 125
"Masonry", the secretariat of which is held by BSI.
The initial draft of this document was prepared by the European section of International Union of
Contractors of Plastering, Dry Lining, Stucco and Related Activities (UIEP) at the request of the
CEN Technical Sector Board (Resolution No.BTS1/56/1991). It has been revised by
CEN/TC125/JWG5 in conjunction with CEN/TC241 using a document prepared by Eurogypsum. The
CEN technical report gives in different sections guidance for building details, design and materials
considerations, the selection of mixes and the application of gypsum plasters. Relevant data are
summarized in a series of tables. This document applies to gypsum plasters conforming to prEN
13279-1, applied as an internal plaster The recommendations are framed in logical sequence, namely
materials and accessories; properties of backgrounds that influence the choice of suitable gypsum
plastering systems; guidance on preparation of surfaces to be plastered; choice of suitable gypsum
plastering systems; methods of application. It is essential that the design clauses are read in
conjunction with the clauses on background and preparation.
It is not the function of this document to assign responsibility for the design and application of any
work or actions mentioned within to any specific party. Such responsibility is a matter for other
documentation associated with the work, e.g. the contract.
It has been assumed in the draft
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
CEN/TR 16239:2011(Main)
Installation rules of fibrous (gypsum) plaster works
SIST-TP CEN/TR 16239:2011

This Technical Report provides details on the rules and recommendations for the installation of works carried
out using fibrous (gypsum) plaster casts as defined in European Standard EN 13815, with instructions and
details about construction.
Fibrous (gypsum) plaster casts from the three categories of production below (see 4.1 of EN 13815:2006)
should be involved in this Technical Report:
a) "cpp" allowing regulatory marking CE,
b) "cppv" allowing regulatory marking CE,
c) "ipp" either when CE marking is required or without CE marking (see Annex D, note 2 of EN 13815:2006).
There are three products:
- traditional fibrous (gypsum) plaster casts, and two specific products:
- GRG casts,
- PMGRG casts.
NOTE 1 Construction of traditional gypsum plaster works using screwed system, showing similar provisions with GRG
works screwed construction, is not dealt in this Technical Report.
NOTE 2 PMGRG works are not dealt in this Technical Report.
There are three ranges of casts, defined by their principal functions shapes and configurations (see 4.2 of
EN 13815:2006):
- casts for interior architecture,
- casts for technical functions and
- units.
The equipment, accessories and devices are defined in this document.
This Technical Report applies to both new construction and to the refurbishment, restructuring or conversion
of existing buildings.
Fibrous plastering work should be capable of having the usual finishes applied directly to them (e.g. paint,
wallpaper), subject to the normal preparatory work applicable for the finish.
This Technical Report should not apply to:
- works consisting of various boards, elements or casts when they are not fibrous (gypsum) plaster casts or
fibrous plaster works which, by their nature, do not form an integral part of the structure by the use of
permanent fixing (see the scope of EN 15319:2007).
- fibrous plaster works consisting of casts and embellishments, when they are to be applied directly to
either new or existing wall or ceiling surfaces, for purely decorative applications (see Figures 3 and 4 of
EN 15319:2007); works of these types should be carried out in accordance with standard practice.
This Technical Report does not contain the regulatory requirements with which fibrous plaster works (e.g.
ceiling) must comply in certain buildings.
FprCEN/TR 16239:2011 (E)
6
NOTE 3 In the field of safety, most regulations relate to certain types of building for example:
- public buildings (PB),
- high rise buildings (HRB),
- buildings for educational purposes,
- buildings for sanitary purposes.
This Technical Report does not deal with the ability of fibrous plastering works to comply with particular
technical requirements (e.g. fire behaviour, protection against noise, energy economy, etc) needed for the
works to comply with the requirements of the particular building contract.

  • Technical report
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 22435:2024(Main)
Gas cylinders - Cylinder valves with integrated pressure regulators - Specification and type testing (ISO 22435:2024)
kSIST FprEN ISO 22435:2024

This document specifies design, type test methods, marking and instruction requirements for cylinder valves with integrated pressure regulators (VIPRs) intended to be fitted to gas cylinders, pressure drums or tubes or used as a main valve for bundles of cylinders that convey compressed, liquefied or dissolved gases.
These are requirements for VIPRs that are in addition to those given in the relevant closure standard, for example, in ISO 10297 for cylinder valves, in ISO 17871 for quick-release cylinder valves, in ISO 17879 for self-closing cylinder valves or in ISO 23826 for ball valves. For ISO 17871, these requirements are only applicable to quick-release cylinder valves types B, C, D and E.
NOTE 1        If the pressure regulating system of a VIPR is acting as the primary valve operating mechanism, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826. This also includes designs where closure of the primary valve operating mechanism of a VIPR is obtained by closing the seat of the pressure regulating system.
NOTE 2        If the primary valve operating mechanism of a VIPR is located at the low-pressure side of the pressure regulating system, it is covered by the relevant closure standard, e.g. ISO 10297, ISO 17871, ISO 17879 and ISO 23826.
NOTE 3        The term “pressure receptacle” is used within this document to cover instances where no differentiation is necessary between gas cylinders, bundles of cylinders, pressure drums and tubes.
This document does not apply to VIPRs for
a)       medical applications (see ISO 10524-3);
b)       liquefied petroleum gas (LPG);
c)        cryogenic applications.
NOTE 4        Additional requirements for a VIPR with a residual pressure device (RPD) are specified in ISO 15996.
NOTE 5        Additional requirements for pressure relief valves can exist in international/regional regulations/ standards.

  • Draft
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17015-1:2024(Main)
Electronic Public Procurement - Catalogue - Part 1: Choreographies
kSIST FprEN 17015-1:2024

The purpose of this deliverable is to specify and describe choreographies for exchanging an electronic product catalogue (“catalogues”) as part of the business processes in the pre-award and post-award area, so that catalogues can serve as a basis for placing orders as well as evaluating tenders. The key aspects covered by this choreography specification are:
-   processes for submitting catalogues from the selling to the buying side;
-   processes for submitting catalogue-related data as part of a tendering process;
-   processes integrating sell-side procurement systems.
This document does not apply to the transactions used in the specified choreographies. These transactions are specified in EN 17015 2. The relationship between the choreographies and the transaction is described in Clause 8.
The identifier of this choreographies document is EN 17015 1:2024.
How to claim compliance to this choreography is specified in 6.2.3.

  • Draft
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO/ASTM 52927:2024(Main)
Additive manufacturing - General principles - Main characteristics and corresponding test methods (ISO/ASTM 52927:2024)
kSIST FprEN ISO/ASTM 52927:2024

This document specifies the principal requirements applied to the testing of parts produced by additive manufacturing processes.
This document
—     identifies quality characteristics for feedstock and parts and the corresponding test procedures,
—     provides the specific procedures to build specimens using additive manufacturing process, and
—     recommends the scope and content of test and supply agreements.
This document is aimed at machine manufacturers, feedstock suppliers, AM system users, part providers, and customers to facilitate the communication on main quality characteristics. It applies wherever additive manufacturing processes are used.
NOTE            It is the intent to include, in future versions of this document, other characteristics such as thermal properties, electrical requirements and physical and physico-chemical properties based upon material types.

  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 8362-2:2024(Main)
Injection containers and accessories - Part 2: Closures for injection vials (ISO 8362-2:2024)
SIST EN ISO 8362-2:2024

This document specifies the shape, dimensions, material, performance requirements and labelling of closures for injection vials covered by ISO 8362-1 and ISO 8362-4.
The dimensional requirements are not applicable to barrier-coated closures.
Closures specified in this document are intended for single use only.
NOTE            The potency, purity, stability and safety of a medicinal product during its manufacture and storage can strongly be affected by the nature and performance of the primary packaging.

  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 16739-1:2024(Main)
Industry Foundation Classes (IFC) for data sharing in the construction and facility management industries - Part 1: Data schema (ISO 16739-1:2024)
kSIST FprEN ISO 16739-1:2024

This document represents an open international standard for information used in Building Information Modeling (BIM) that is exchanged and shared among software applications used by the various participants in the construction or facility management industry sector. This document includes definitions that cover information required for buildings and infrastructure works over their life cycle. This edition of the document added coverage of information required for infrastructure facilities including bridges, roads, railways, waterways and port facilities.
This document comprises the publication of a data schema, its documentation, the property and quantity set definitions and the mechanism of an exchange file format structure.
Definitions from this document are used to support different recognized work flows in the construction and facility management industry sector, representing information deliveries. Such information deliveries can be described according to ISO 29481.
Different implementation levels of this document can be defined to better support multiple information deliveries, they are referred to as a Model View Definition (MVD). Each MVD identifies which subset of the definitions of this document imposes requirements for implementation in software applications. Conforming software applications need to identify the model view definition they conform to when applying for software certification.
The following are within the scope of this edition of this document:
BIM exchange format definitions that are required during the life cycle phases of buildings and infrastructure:
demonstrating the need;
conception of need;
outline feasibility;
substantive feasibility study and outline financial authority;
outline conceptual design;
full conceptual design;
coordinated design;
procurement and full financial authority;
production information;
construction;
operation and maintenance.
BIM exchange format definitions that are required by the various disciplines involved within the life cycle phases:
architecture and civil engineering design;
service and utilities engineering;
structural engineering;
procurement;
construction planning;
facility and utility management;
project management;
client requirement management;
industry authorities for permits and approval.
BIM exchange format definitions including:
project structure;
physical components;
spatial components;
analysis items;
processes;
resources;
controls;
actors;
context definition.

  • Draft
    406 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 2620:2024(Main)
Analysis of natural gas - Biomethane - Determination of VOCs by thermal desorption gas chromatography with flame ionization and/or mass spectrometry detectors (ISO 2620:2024)
kSIST FprEN ISO 2620:2024

This document describes a method for sampling and analysis of volatile organic compounds (VOCs), including siloxanes, terpenes, organic sulfur compounds, in natural gas and biomethane matrices, using thermal desorption gas chromatography with flame ionization and/or mass spectrometry detectors (TD-GC-FID/MS).

  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 4126-10:2024(Main)
Safety devices for protection against excessive pressure - Part 10: Sizing of safety valves and bursting discs for gas/liquid two-phase flow (ISO 4126-10:2024)
kSIST FprEN ISO 4126-10:2023

This document specifies the sizing of safety valves and bursting discs for gas/liquid two-phase flow in pressurized systems such as reactors, storage tanks, columns, heat exchangers, piping systems or transportation tanks/containers, see Figure 2. The possible fluid states at the safety device inlet that can result in two-phase flow are given in Table 1.
NOTE          The pressures used in this document are absolute pressures, not gauge pressures.

  • Draft
    84 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 17294-1:2024(Main)
Water quality - Application of inductively coupled plasma mass spectrometry (ICP-MS) - Part 1: General requirements (ISO 17294-1:2024)
kSIST FprEN ISO 17294-1:2023

This document specifies the principles of inductively coupled plasma mass spectrometry (ICP-MS) and provides general requirements for the use of this technique to determine elements in water, digests of sludges and sediments (e.g. digests of water as described in ISO 15587-1 or ISO 15587-2). Generally, the measurement is carried out in water, but gases, vapours or fine particulate matter can be introduced too. This document applies to the use of ICP-MS for aqueous solution analysis.
The ultimate determination of the elements is described in a separate International Standard for each series of elements and matrix. The individual clauses of this document refer the user to these guidelines for the basic principles of the method and the configuration of the instrument.

  • Draft
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17016-1:2024(Main)
Electronic Public Procurement - Ordering - Part 1: Choreographies
kSIST prEN 17016-1:2024

This choreographies document specify ordering between Buyer and Seller where the Buyer wants to reach an agreement with the Seller about an order. It specifies a series of activities that govern communication between the parties and refers to the specifications where information and rules that apply are specified.
The various possible behaviours of the Seller and Buyer subsequent to the first order communication are conveyed by variants of this choreography that are specified in 5.2.
Previous activities (e.g. cataloguing) and subsequent activities (e.g. invoicing) are outside the scope of this document. If performed electronically, their implementation is covered by other choreographies.
The identifier of this choreographies document is EN 17016-1:2024.
How to claim compliance to this choreography is specified in 5.2.3.

  • Draft
    74 pages
    English language
    sale 10% off
    e-Library read for
    1 day