EN ISO 7233:2016

Rubber and plastics hoses and hose assemblies - Determination of resistance to vacuum (ISO 7233:2016)

ISO 7233:2016 specifies three methods for determining the resistance to vacuum of hoses and hose assemblies manufactured from plastic or rubber. Applicable dimensions of hoses for each method are as follows:
- method A for hoses of nominal bore up to and including 80 mm;
- method B for hoses of nominal bore greater than 80 mm;
- method C for hoses of all dimensions.
Methods A and B can also be used to check the adhesion of the lining to the reinforcement (delamination) in a length of hard-wall hose or hose assembly.

Gummi- und Kunststoffschläuche und -schlauchleitungen - Bestimmung der Beständigkeit gegen Vakuum (ISO 7233:2016)

Diese Internationale Norm legt drei Verfahren zur Bestimmung der Beständigkeit von Schläuchen und Schlauchleitungen aus Kunststoff oder Gummi gegen Vakuum fest. Für jedes Verfahren sind im Folgenden die zutreffenden Schlauchmaße angegeben:
-   Verfahren A - für Schläuche mit einem Nenn-Innendurchmesser bis einschließlich 80 mm;
-   Verfahren B - für Schläuche mit einem Nenn-Innendurchmesser über 80 mm;
-   Verfahren C - für alle Schlauchmaße.
Die Verfahren A und B können auch zur Prüfung der Haftung zwischen Innenschicht und Verstärkungselement (Schichtablösung) in der Länge eines Schlauches mit Wendel oder einer Schlauchleitung verwendet werden.

Tuyaux et flexibles en caoutchouc et en plastique - Détermination de la résistance à l'aspiration (ISO 7233:2016)

ISO 7233:2016 spécifie trois méthodes pour la détermination de la résistance à l'aspiration des tuyaux et des flexibles fabriqués à partir de plastique ou de caoutchouc. Les dimensions s'appliquant aux tuyaux pour chaque méthode sont les suivantes:
- méthode A pour tuyaux de diamètre intérieur nominal inférieur ou égal à 80 mm;
- méthode B pour tuyaux de diamètre intérieur nominal supérieur à 80 mm;
- méthode C pour tuyaux de toutes les dimensions.
Les méthodes A et B peuvent également être utilisées pour vérifier l'adhérence entre le tube intérieur et le renforcement (délamination) dans une longueur de tuyau ou de flexible de raccordement renforcé.

Gumene in polimerne cevi ter cevni priključki - Ugotavljanje odpornosti proti vakuumu (ISO 7233:2016)

Ta dokument določa tri metode za ugotavljanje odpornosti proti vakuumu cevi in cevnih priključkov, izdelanih iz polimerov ali gume. Primerne dimenzije cevi za posamezno metodo
so naslednje:
– metoda A za cevi z nominalnim premerom največ 80 mm;
– metoda B za cevi z nominalnim premerom več kot 80 mm;
– metoda C za cevi vseh dimenzij.
Metodi A in B se lahko uporabljata tudi za preverjanje pritrditve obloge na ojačitev (razslojevanje) v dolžini cevi ali cevnih priključkov s togimi stenami.

General Information

• Status: Withdrawn
• Publication Date: 25-Oct-2016
• Withdrawal Date: 18-May-2021
• ICS: 23.040.70 - Hoses and hose assemblies
• Technical Committee: CEN/TC 218 - Rubber and plastics hoses and hose assemblies
• Drafting Committee: CEN/TC 218 - Rubber and plastics hoses and hose assemblies
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 19-May-2021
• Ref Project: SIST EN ISO 7233:2016 - Rubber and plastics hoses and hose assemblies - Determination of resistance to vacuum (ISO 7233:2016)

Relations

• Replaces: EN ISO 7233:2008 - Rubber and plastics hoses and hose assemblies - Determination of resistance to vacuum (ISO 7233:2006)
• Effective Date: 17-Dec-2014
• Replaced By: EN ISO 7233:2021 - Rubber and plastics hoses and hose assemblies - Determination of resistance to vacuum (ISO 7233:2021)
• Effective Date: 26-May-2021

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 7233:2016
01-december-2016
1DGRPHãþD
SIST EN ISO 7233:2009
*XPHQHLQSROLPHUQHFHYLWHUFHYQLSULNOMXþNL8JRWDYOMDQMHRGSRUQRVWLSURWL
YDNXXPX,62
Rubber and plastics hoses and hose assemblies - Determination of resistance to vacuum
(ISO 7233:2016)
Tuyaux et flexibles en caoutchouc et en plastique - Détermination de la résistance à
l'aspiration (ISO 7233:2016)
Ta slovenski standard je istoveten z: EN ISO 7233:2016
ICS:
23.040.70 Gumene cevi in armature Hoses and hose assemblies
SIST EN ISO 7233:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 7233:2016

---------------------- Page: 2 ----------------------

SIST EN ISO 7233:2016


EN ISO 7233
EUROPEAN STANDARD

NORME EUROPÉENNE

October 2016
EUROPÄISCHE NORM
ICS 23.040.70 Supersedes EN ISO 7233:2008
English Version

Rubber and plastics hoses and hose assemblies -
Determination of resistance to vacuum (ISO 7233:2016)
Tuyaux et flexibles en caoutchouc et en plastique -
Détermination de la résistance à l'aspiration (ISO
7233:2016)
This European Standard was approved by CEN on 24 October 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 7233:2016 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 7233:2016
EN ISO 7233:2016 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 7233:2016
EN ISO 7233:2016 (E)
European foreword
This document (EN ISO 7233:2016) has been prepared by Technical Committee ISO/TC 45 "Rubber and
rubber products" in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses
and hose assemblies” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2017, and conflicting national standards shall be
withdrawn at the latest by April 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 7233:2008.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 7233:2016 has been approved by CEN as EN ISO 7233:2016 without any modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 7233:2016

---------------------- Page: 6 ----------------------

SIST EN ISO 7233:2016
INTERNATIONAL ISO
STANDARD 7233
Fourth edition
2016-10-15
Rubber and plastics hoses and hose
assemblies — Determination of
resistance to vacuum
Tuyaux et flexibles en caoutchouc et en plastique — Détermination de
la résistance à l’aspiration
Reference number
ISO 7233:2016(E)
©
ISO 2016

---------------------- Page: 7 -
...