EN ISO 1163-1:1999

Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 1163-1:1995)

Gives a system of designation for unplasticized polyvinyl chloride (PVC-U) moulding and extrusion materials which may be used as the basis for specifications. Applicable to all unplasticized polyvinyl chloride compositions that contain at least 50 % m/m of vinyl chloride. Does not apply to cellular plastics. Replaces the second edition.

Kunststoffe - Weichmacherfreie Polyvinylchlorid (PVC-U) - Formmassen - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 1163-1:1995)

Plastiques - Poly(chlorure de vinyle) non plastifié (PVC-U) pour moulage et extrusion - Partie 1: Système de désignation et base de spécification (ISO 1163-1:1995)

La présente partie de l'ISO 1163 est applicable à toutes les compositions non plastifiées d'homopolymères et de copolymères qui contiennent au moins 50 % Wm) de chlorure de vinyle. Elle est également applicable aux compositions qui contiennent du poly(chlorure de vinyle) chloré et à celles qui contiennent des mélanges constitués d'un ou plusieurs polymères parmi ceux susmentionnés, sous réserve que la teneur totale en ces polymères soit égale à au moins 50 % (rdm) du mélange de polymères de la composition. Elle s'applique aux matériaux prêts à l'emploi sous forme de poudre, grains ou granulés, non modifiés ou modifiés par des colorants, additifs, charges, etc. La présente partie de l'ISO 1163 ne s'applique pas aux plastiques alvéolaires. Le fait que des matériaux aient la même désignation n'implique pas qu'ils présentent nécessairement les mêmes performances. La présente partie de l'ISO 1163 ne comporte pas de données sur la conception, la performance ou les conditions de mise en oeuvre qui peuvent être exigées pour spécifier un matériau pour une application et/ou une méthode de mise en oeuvre particulière. Si de telles propriétés additionnelles sont nécessaires, elles peuvent être déterminées conformément aux méthodes d'essai prescrites dans l'ISO 1163-2, si appropriée. Afin de prescrire un matériau thermoplastique pour une application particulière ou d'assurer une méthode de mise en oeuvre reproductible, des exigences additionnelles peuvent être codées dans le bloc de données 5 (voir article 3, alinéa d'introduction).

Polimerni materiali - Nemehčane zmesi homo- in kopolimerov vinilklorida - 1. del: Sistem označevanja in podlage za specifikacije (ISO 1163-1:1995)

General Information

• Status: Withdrawn
• Publication Date: 22-Jun-1999
• Withdrawal Date: 09-Apr-2019
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: CEN/TC 249 - Plastics
• Drafting Committee: CEN/TC 249 - Plastics
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 10-Apr-2019
• Ref Project: SIST EN ISO 1163-1:2000 - Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 1163-1:1995)

Relations

• Replaced By: EN ISO 21306-1:2019 - Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 21306-1:2019)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
01-maj-2000
3ROLPHUQLPDWHULDOL1HPHKþDQH]PHVLKRPRLQNRSROLPHURYYLQLONORULGDGHO
6LVWHPR]QDþHYDQMDLQSRGODJH]DVSHFLILNDFLMH,62
Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials -
Part 1: Designation system and basis for specifications (ISO 1163-1:1995)
Kunststoffe - Weichmacherfreie Polyvinylchlorid (PVC-U) - Formmassen - Teil 1:
Bezeichnungssystem und Basis für Spezifikationen (ISO 1163-1:1995)
Plastiques - Poly(chlorure de vinyle) non plastifié (PVC-U) pour moulage et extrusion -
Partie 1: Systeme de désignation et base de spécification (ISO 1163-1:1995)
Ta slovenski standard je istoveten z: EN ISO 1163-1:1999
ICS:
83.080.20 Plastomeri Thermoplastic materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

INTERNATIONAL ISO
1163-1
STANDARD
Third edition
1995-12-15
Plastics - Unplasticized poly(vinyl
chloride) (PVC-U) moulding and extrusion
materials -
Part 1:
Designation System and basis for
specifications
Plas tiques - Poly(chlorure de vinyle) non plastifie (PVC-U) pour moulage
et extrusion -
Partie 7: Systeme de d&igna tion et base de specifica tion
Reference number
ISO 1163-1:1995(E)
ISO 1163=1:1995(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national Standards bodies (ISO member bodies). The work
of preparing International Standards is normally carried out through ISO
technical committees. Esch member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(1 EC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 1163-1 was prepared by Technical Committee
lSO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic materials.
This third edition cancels and replaces the second edition (ISO
1163-1:1985), which has been technically revised. The main changes
concern the code-numbers and ranges for the impact strength and
modulus of elasticity in table 2.
ISO 1163 consists of the following Parts, under the general title
Plas tics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and
extrusion ma terials:
- Part 1: Designa tion System and basis for specifica tions
- Part 2: Preparation of test specimens and determination of proper-
ties
0 ISO 1995
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronie or mechanical, including photocopying and
microfilm, without Permission in writing from the publisher.
International Organization for Standardization
Case Postale 56GH-121 1 Geneve 20 l Switzerland
Printed in Switzerland
INTERNATIONAL STANDARD 0 ISO ISO 1163=1:1995(E)
- Unplasticized poly(vinyl chloride) (PVC-U)
Plastics
moulding and extrusion materials -
Part 1:
Designation System and basis for specifications
1 Scope
1.1 This part of ISO 1163 establishes a System of designation for unplasticized PVC thermoplastic material which
may be used as the basis for specifications.
1.2 The types of PVC-U plastics are differentiated from each other by a classification System based on appro-
priate levels of the designatory properties
a) Vicat softening temperature
b) impact strength (Charpy notched)
c) modulus of elasticity
and on information about basic polymer Parameters, intended application and/or method of processing, important
properties, additives, colorants, fillers and reinforcing materials.
1.3 This part of ISO 1163 is applicable to all unplasticized compositions of homopolymers and copolymers that
contain at least 50 % (m/m) of Vinyl chloride. lt is also applicable to compositions containing chlorinated poly(vinyl
chloride) and to compositions containing blends of one or more of the above-mentioned polymers, provided that
the total amount of these polymers represents at least 50 % (m/m) of the polymer content of the composition.
lt applies to materials ready for normal use in the form of powder, granules or pellets and to materials unmodified
or modified by colorants, additives, fillers, etc.
This part of ISO 1163 does not apply to cellular plastics.
1.4 lt is not intended to imply that materials having the Same designation give necessarily the Same perform-
ante. This part of ISO 1163 does not provide engineering data, Performance data or data on processing conditions
which may be required to specify a material for a particular application and/or method or processing.
If such additional properties are required, they may be determined in accordance with the test methods specified
in part 2 of this International Standard, if suitable.
1.5 In Order to specify a thermoplastic material for a particular application or to ensure reproducible processing,
additional requirements may be given in data block 5 (see clause 3, introductory Paragraph).

0 ISO
ISO 116301:1995(E)
2 Normative references
The following Standards contain provisions which, through reference in this text, constitute provisions of this part
of ISO 1163. At the time of publication, the editions indicated were valid. All Standards are subject to revision, and
Parties to agreements based on this part of ISO 1163 are encouraged to investigate the possibility of applying the
most recent editions of the Standards indicated below. Members of IEC and ISO maintain registers of currently
valid International Standards.
ISO 1043-1: 1987, Plastics - Symbols - Part 1: Basic polymers and their special characteristics.
Unplasticized polyfvinyl chloride) (PVC-U) moulding and extrusion ma terials -
ISO 1163-2:1995, Plastics -
Part 2: Preparation of test specimens and determination of properties.
3 Designation and specification System
The d
...