GRP tanks and vessels for use above ground - Part 1: Raw materials - Specification conditions and acceptance criteria

This document gives requirements for specification and acceptance conditions of raw materials for GRP tanks and vessels with or without lining for storage or processing of fluids, factory made or site built, non-pressurised or pressurised, for use above ground.
Tanks and vessels for storage or processing of food, raw materials for food and potable water additionally have to be in compliance with relevant EU directives and applicable national standards and regulations.

Oberirdische GFK-Tanks und -Behälter - Teil 1: Ausgangsmaterialien - Spezifikations- und Abnahmebedingungen

Dieses Dokument enthält die Anforderungen an die Spezifikation und Annahme von Ausgangsmaterialien für GFK-Tanks und -Behälter mit oder ohne Auskleidung, werksmäßig hergestellt oder standortgefertigt, zur oberirdischen Lagerung oder Behandlung von Fluiden, drucklos oder druckbeaufschlagt. In Verbindung mit den Bedingungen für die Herstellung der drucktragenden Werkstoffe nach EN 13121 3:2016 stellen die Spezifikations- und Annahmebedingungen für die Ausgangsmaterialien sicher, dass der Tank oder Behälter geeignet ist, die Anforderungen an seine Auslegung zu erfüllen, insbesondere hinsichtlich der Anforderungen an seine chemisch/thermische Widerstandsfähigkeit sowie an die Aufnahme des Drucks und der Lasten.
ANMERKUNG Tanks und Behälter für die Lagerung oder Verarbeitung von Lebensmitteln, Rohmaterialien für Lebensmittel und Trinkwasser werden zusätzlich die Anforderungen der relevanten EG-Richtlinien und anzuwendenden nationalen Normen und Vorschriften erfüllen.

Réservoirs et récipients en PRV pour applications hors sol - Partie 1 : Matières premières - Conditions de spécification et critères d’acceptation

Le présent document définit les exigences relatives aux conditions de spécification et aux conditions de réception des matières premières destinées à la fabrication des réservoirs et récipients en PRV avec ou sans revêtement, destinés au stockage ou au traitement de fluides, fabriqués en usine ou sur site, avec ou sans pression, implantés hors sol.
NOTE   Les réservoirs et récipients pour le stockage ou le traitement de denrées alimentaires, de matières premières pour les denrées alimentaires et d’eau potable vont en outre être en conformité avec les Directives UE correspondantes et les normes nationales et réglementations applicables.

Nadzemni rezervoarji in posode iz umetnih mas, ojačanih s steklenimi vlakni - 1. del: Osnovni materiali - Specifikacije in kriteriji sprejemljivosti

General Information

Status
Published
Publication Date
21-Sep-2021
Withdrawal Date
30-Mar-2022
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
22-Sep-2021
Due Date
28-Apr-2021
Completion Date
22-Sep-2021

Relations

Buy Standard

Standard
EN 13121-1:2021
English language
23 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN 13121-1:2019
English language
21 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 13121-1:2021
01-december-2021
Nadomešča:
SIST EN 13121-1:2003
Nadzemni rezervoarji in posode iz umetnih mas, ojačanih s steklenimi vlakni - 1.
del: Osnovni materiali - Specifikacije in kriteriji sprejemljivosti
GRP tanks and vessels for use above ground - Part 1: Raw materials - Specification
conditions and acceptance criteria
Oberirdische GFK-Tanks und -Behälter - Teil 1: Ausgangsmaterialien - Spezifikations-
und Abnahmebedingungen
Réservoirs et récipients en PRV pour applications hors sol - Partie 1 : Matières
premières - Specifications et Criteres d'acceptation
Ta slovenski standard je istoveten z: EN 13121-1:2021
ICS:
23.020.10 Nepremične posode in Stationary containers and
rezervoarji tanks
SIST EN 13121-1:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 13121-1:2021

---------------------- Page: 2 ----------------------
SIST EN 13121-1:2021


EN 13121-1
EUROPEAN STANDARD

NORME EUROPÉENNE

September 2021
EUROPÄISCHE NORM
ICS 23.020.10 Supersedes EN 13121-1:2003
English Version

GRP tanks and vessels for use above ground - Part 1: Raw
materials - Specification conditions and acceptance criteria
Réservoirs et récipients en PRV pour applications hors Oberirdische GFK-Tanks und -Behälter - Teil 1:
sol - Partie 1 : Matières premières - Conditions de Ausgangsmaterialien - Spezifikations- und
spécification et critères d'acceptation Abnahmebedingungen
This European Standard was approved by CEN on 25 July 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13121-1:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 13121-1:2021
EN 13121-1:2021 (E)
Contents Page

European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, symbols and abbreviations . 8
3.1 Terms and definitions . 8
3.2 Symbols and abbreviations . 8
4 Thermosetting resins . 9
4.1 General . 9
4.2 Unsaturated polyester resins . 11
4.3 Vinylester resins . 11
4.4 Vinylester urethane resins .
...

SLOVENSKI STANDARD
oSIST prEN 13121-1:2019
01-maj-2019
Nadzemni rezervoarji iz armiranega poliestra - 1. del: Osnovni material - Zahteve za
specifikacije in prevzemni pogoji/merila
GRP tanks and vessels for use above ground - Part 1: Raw materials - Specification
conditions and acceptance criteria
Oberirdische GFK-Tanks und -Behälter - Teil 1: Ausgangsmaterialien - Spezifikations-
und Abnahmebedingungen
Réservoirs et récipients en PRV pour applications hors sol - Partie 1 : Matières
premières - Specifications et Criteres d'acceptation
Ta slovenski standard je istoveten z: prEN 13121-1
ICS:
23.020.10 1HSUHPLþQHSRVRGHLQ Stationary containers and
UH]HUYRDUML tanks
oSIST prEN 13121-1:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 13121-1:2019

---------------------- Page: 2 ----------------------
oSIST prEN 13121-1:2019


DRAFT
EUROPEAN STANDARD
prEN 13121-1
NORME EUROPÉENNE

EUROPÄISCHE NORM

April 2019
ICS 23.020.10 Will supersede EN 13121-1:2003
English Version

GRP tanks and vessels for use above ground - Part 1: Raw
materials - Specification conditions and acceptance criteria
Réservoirs et récipients en PRV pour applications hors Oberirdische GFK-Tanks und -Behälter - Teil 1:
sol - Partie 1 : Matières premières - Specifications et Ausgangsmaterialien - Spezifikations- und
Criteres d'acceptation Abnahmebedingungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 210.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13121-1:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 13121-1:2019
prEN 13121-1:2019 (E)
Contents           Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms, definitions, symbols and abbreviations . 8
3.1 Terms and definitions . 8
3.2 Symbols and abbreviations . 8
4 Thermosetting resins . 8
4.1 General . 8
4.2 Unsaturated polyester resins .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.