EN ISO 3501:2022

Plastics piping systems - Mechanical joints between fittings and pressure pipes - Test method for resistance to pull-out under constant longitudinal force (ISO 3501:2021)

This document specifies a method for checking the ability of assembled uniaxial joints between fittings and plastic pressure pipes to withstand longitudinal tensile stresses. The test applies regardless of the design and material of the fitting used for jointing plastics pipe.
This test method is not applicable to fusion-welded joints.

Kunststoff-Rohrleitungssysteme - Mechanische Verbindungen zwischen Formstücken und Druckrohren - Prüfung des Widerstandes gegen Zugbelastung bei konstanter Zugkraft (ISO 3501:2021)

Dieses Dokument legt ein Verfahren zur Prüfung der Eignung von einachsigen Montage¬verbindungen zwischen Formstücken und Kunststoff-Druckrohren, axialen Zugbeanspruchungen (Zug¬spannungen) zu widerstehen, fest. Die Prüfung ist anzuwenden unabhängig von der konstruktiven Auslegung und dem Werkstoff des Formstücks, das für die Verbindung der Kunststoffrohre verwendet wird.
Das Prüfverfahren gilt nicht für Schmelzschweißverbindungen.

Systèmes de canalisations en plastique - Assemblages mécaniques entre raccords et tubes sous pression - Méthode d'essai de résistance à l'arrachement sous une force longitudinale constante (ISO 3501:2021)

Le présent document spécifie une méthode de vérification de la résistance à la traction longitudinale des assemblages uniaxiaux entre raccords et tubes plastiques sous pression. L’essai s’applique, quelles que soient la conception et la matière du raccord utilisé pour le raccordement des tubes plastiques.
La présente méthode d’essai n’est pas applicable aux assemblages soudés par fusion.

Cevni sistemi iz polimernih materialov - Mehanski spoji med fitingi in tlačnimi cevmi - Metoda za preskus odpornosti proti izvlečenju s konstantno osno obremenitvijo (ISO 3501:2021)

Ta dokument določa metodo za preverjanje zmožnosti sestavljenih enoosnih spojev med fitingi
in plastičnimi tlačnimi cevmi, da prenesejo osne natezne obremenitve. Preskus se uporablja ne glede na
konstrukcijo in material fitinga za spajanje plastičnih cevi.
Ta preskusna metoda se ne uporablja za talilno zvarjene spoje.

General Information

• Status: Published
• Publication Date: 11-Jan-2022
• Withdrawal Date: 30-Jul-2022
• ICS: 23.040.60 - Flanges, couplings and joints
• Technical Committee: CEN/TC 155 - Plastics piping systems and ducting systems
• Drafting Committee: CEN/TC 155 - Plastics piping systems and ducting systems
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 12-Jan-2022
• Completion Date: 12-Jan-2022
• Ref Project: SIST EN ISO 3501:2022 - Plastics piping systems - Mechanical joints between fittings and pressure pipes - Test method for resistance to pull-out under constant longitudinal force (ISO 3501:2021)

Relations

• Replaces: EN ISO 3501:2015 - Plastics piping systems - Mechanical joints between fittings and pressure pipes - Test method for resistance to pull-out under constant longitudinal force (ISO 3501:2015)
• Effective Date: 19-Jan-2022

Standards Content (Sample)

SLOVENSKI STANDARD
01-april-2022
Nadomešča:
SIST EN ISO 3501:2015
Cevni sistemi iz polimernih materialov - Mehanski spoji med fitingi in tlačnimi
cevmi - Metoda za preskus odpornosti proti izvlečenju s konstantno osno
obremenitvijo (ISO 3501:2021)
Plastics piping systems - Mechanical joints between fittings and pressure pipes - Test
method for resistance to pull-out under constant longitudinal force (ISO 3501:2021)
Kunststoff-Rohrleitungssysteme - Mechanische Verbindungen zwischen Formstücken
und Druckrohren - Prüfung des Widerstandes gegen Zugbelastung bei konstanter
Zugkraft (ISO 3501:2021)
Systèmes de canalisations en plastique - Assemblages mécaniques entre raccords et
tubes sous pression - Méthode d'essai de résistance à l'arrachement sous une force
longitudinale constante (ISO 3501:2021)
Ta slovenski standard je istoveten z: EN ISO 3501:2022
ICS:
23.040.60 Prirobnice, oglavki in spojni Flanges, couplings and joints
elementi
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 3501
EUROPEAN STANDARD
NORME EUROPÉENNE
January 2022
EUROPÄISCHE NORM
ICS 23.040.60 Supersedes EN ISO 3501:2015
English Version
Plastics piping systems - Mechanical joints between
fittings and pressure pipes - Test method for resistance to
pull-out under constant longitudinal force (ISO
3501:2021)
Systèmes de canalisations en plastique - Assemblages Kunststoff-Rohrleitungssysteme - Mechanische
mécaniques entre raccords et tubes sous pression - Verbindungen zwischen Formstücken und
Méthode d'essai de résistance à l'arrachement sous Druckrohren - Prüfung des Widerstandes gegen
une force longitudinale constante (ISO 3501:2021) Zugbelastung bei konstanter Zugkraft (ISO 3501:2021)
This European Standard was approved by CEN on 27 December 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3501:2022 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 3501:2022) has been prepared by Technical Committee ISO/TC 138 "Plastics
pipes, fittings and valves for the transport of fluids" in collaboration with Technical Committee CEN/TC
155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by July 2022, and conflicting national standards shall be
withdrawn at the latest by July 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 3501:2015.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 3501:2021 has been approved by CEN as EN ISO 3501:2022 without any modification.

INTERNATIONAL ISO
STANDARD 3501
Third edition
2021-12
Plastics piping systems — Mechanical
joints between fittings and pressure
pipes — Test method for resistance to
pull-out under constant longitudinal
force
Systèmes de canalisations en plastique — Assemblages mécaniques
entre raccords et tubes sous pression — Méthode d'essai de résistance
à l'arrachement sous une force longitudinale constante
Reference number
ISO 3501:2021(E)
ISO 3501:2021(E)
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
ISO 3501:2021(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Test parameters and requirements .1
6 Apparatus . 2
7 Test pieces .3
8 Procedure .3
9 Test report . 3
Annex A (normative) Test parameters . 4
iii
ISO 3501:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The proc
...