Plastics piping systems - Mechanical joints between fittings and pressure pipes - Test method for resistance to pull-out under constant longitudinal force (ISO 3501:2021)

This document specifies a method for checking the ability of assembled uniaxial joints between fittings
and plastic pressure pipes to withstand longitudinal tensile stresses. The test applies regardless of the
design and material of the fitting used for jointing plastics pipe.
This test method is not applicable to fusion-welded joints.

Kunststoff-Rohrleitungssysteme - Mechanische Verbindungen zwischen Formstücken und Druckrohren - Prüfung des Widerstandes gegen Zugbelastung bei konstanter Zugkraft (ISO 3501:2021)

Diese Internationale Norm legt ein Verfahren zur Prüfung der Eignung von einachsigen Montage-verbindungen zwischen Formstücken und Kunststoff-Druckrohren, axialen Zugbeanspruchungen (Zug-spannungen) zu widerstehen, fest. Die Prüfung gilt unabhängig von der konstruktiven Auslegung und dem Werkstoff des Formstücks, das für die Verbindung der Kunststoffrohre verwendet wird.
Das Prüfverfahren gilt nicht für Schmelzschweißverbindungen.

Systèmes de canalisations en plastique - Assemblages mécaniques entre raccords et tubes sous pression - Méthode d'essai de résistance à l'arrachement sous une force longitudinale constante (ISO 3501:2021)

Le présent document spécifie une méthode de vérification de la résistance à la traction longitudinale des assemblages uniaxiaux entre raccords et tubes plastiques sous pression. L’essai s’applique, quelles que soient la conception et la matière du raccord utilisé pour le raccordement des tubes plastiques.
La présente méthode d’essai n’est pas applicable aux assemblages soudés par fusion.

Cevni sistemi iz polimernih materialov - Mehanski spoji med fitingi in tlačnimi cevmi - Metoda za preskus odpornosti proti izvlečenju s konstantno osno obremenitvijo (ISO 3501:2021)

Ta dokument določa metodo za preverjanje zmožnosti sestavljenih enoosnih spojev med fitingi
in plastičnimi tlačnimi cevmi, da prenesejo osne natezne obremenitve. Preskus se uporablja ne glede na
konstrukcijo in material fitinga za spajanje plastičnih cevi.
Ta preskusna metoda se ne uporablja za talilno zvarjene spoje.

General Information

Status
Published
Public Enquiry End Date
02-Aug-2021
Publication Date
14-Mar-2022
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
18-Feb-2022
Due Date
25-Apr-2022
Completion Date
15-Mar-2022

RELATIONS

Buy Standard

Standard
SIST EN ISO 3501:2022
English language
12 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
oSIST prEN ISO 3501:2021
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN ISO 3501:2022
01-april-2022
Nadomešča:
SIST EN ISO 3501:2015
Cevni sistemi iz polimernih materialov - Mehanski spoji med fitingi in tlačnimi
cevmi - Metoda za preskus odpornosti proti izvlečenju s konstantno osno
obremenitvijo (ISO 3501:2021)

Plastics piping systems - Mechanical joints between fittings and pressure pipes - Test

method for resistance to pull-out under constant longitudinal force (ISO 3501:2021)

Kunststoff-Rohrleitungssysteme - Mechanische Verbindungen zwischen Formstücken
und Druckrohren - Prüfung des Widerstandes gegen Zugbelastung bei konstanter
Zugkraft (ISO 3501:2021)

Systèmes de canalisations en plastique - Assemblages mécaniques entre raccords et

tubes sous pression - Méthode d'essai de résistance à l'arrachement sous une force

longitudinale constante (ISO 3501:2021)
Ta slovenski standard je istoveten z: EN ISO 3501:2022
ICS:
23.040.60 Prirobnice, oglavki in spojni Flanges, couplings and joints
elementi
SIST EN ISO 3501:2022 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 3501:2022
---------------------- Page: 2 ----------------------
SIST EN ISO 3501:2022
EN ISO 3501
EUROPEAN STANDARD
NORME EUROPÉENNE
January 2022
EUROPÄISCHE NORM
ICS 23.040.60 Supersedes EN ISO 3501:2015
English Version
Plastics piping systems - Mechanical joints between
fittings and pressure pipes - Test method for resistance to
pull-out under constant longitudinal force (ISO
3501:2021)

Systèmes de canalisations en plastique - Assemblages Kunststoff-Rohrleitungssysteme - Mechanische

mécaniques entre raccords et tubes sous pression - Verbindungen zwischen Formstücken und

Méthode d'essai de résistance à l'arrachement sous Druckrohren - Prüfung des Widerstandes gegen

une force longitudinale constante (ISO 3501:2021) Zugbelastung bei konstanter Zugkraft (ISO 3501:2021)

This European Standard was approved by CEN on 27 December 2021.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3501:2022 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 3501:2022
EN ISO 3501:2022 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

---------------------- Page: 4 ----------------------
SIST EN ISO 3501:2022
EN ISO 3501:2022 (E)
European foreword

This document (EN ISO 3501:2022) has been prepared by Technical Committee ISO/TC 138 "Plastics

pipes, fittings and valves for the transport of fluids" in collaboration with Technical Committee CEN/TC

155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by July 2022, and conflicting national standards shall be

withdrawn at the latest by July 2022.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN ISO 3501:2015.

Any feedback and questions on this document should be directed to the users’ national standards

body/national committee. A complete listing of these bodies can be found on the CEN website.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,

Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of

North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the

United Kingdom.
Endorsement notice

The text of ISO 3501:2021 has been approved by CEN as EN ISO 3501:2022 without any modification.

---------------------- Page: 5 ----------------------
SIST EN ISO 3501:2022
---------------------- Page: 6 ----------------------
SIST EN ISO 3501:2022
INTERNATIONAL ISO
STANDARD 3501
Third edition
2021-12
Plastics piping systems — Mechanical
joints between fittings and pressure
pipes — Test method for resistance to
pull-out under constant longitudinal
force
Systèmes de canalisations en plastique — Assemblages mécaniques
entre raccords et tubes sous pression — Méthode d'essai de résistance
à l'arrachement sous une force longitudinale constante
Reference number
ISO 3501:2021(E)
© ISO 2021
---------------------- Page: 7 ----------------------
SIST EN ISO 3501:2022
ISO 3501:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on

the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below

or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
© ISO 2021 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 3501:2022
ISO 3501:2021(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ..................................................................................................................................................................................... 1

3 Terms and definitions .................................................................................................................................................................................... 1

4 Principle ........................................................................................................................................................................................................................ 1

5 Test parameters and requirements ................................................................................................................................................1

6 Apparatus .................................................................................................................................................................................................................... 2

7 Test pieces ...................................................................................................................................................................................................................3

8 Procedure ....................................................................................................................................................................................................................3

9 Test report .................................................................................................................................................................................................................. 3

Annex A (normative) Test parameters .............................................................................................................................................................. 4

iii
© ISO 2021 – All rights reserved
---------------------- Page: 9 ----------------------
SIST EN ISO 3501:2022
ISO 3501:2021(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.
The proc
...

SLOVENSKI STANDARD
oSIST prEN ISO 3501:2021
01-julij-2021
Cevni sistemi iz polimernih materialov - Mehanski spoji med fitingi in tlačnimi
cevmi - Metoda za preskus odpornosti proti izvlečenju s konstantno osno
obremenitvijo(ISO/DIS 3501:2021)

Plastics piping systems - Mechanical joints between fittings and pressure pipes - Test

method for resistance to pull-out under constant longitudinal force (ISO/DIS 3501:2021)

Kunststoff-Rohrleitungssysteme - Mechanische Verbindungen zwischen Formstücken
und Druckrohren - Prüfung des Widerstandes gegen Zugbelastung bei konstanter
Zugkraft (ISO/DIS 3501:2021)

Systèmes de canalisations en plastique - Assemblages mécaniques entre raccords et

tubes sous pression - Méthode d'essai de résistance à l'arrachement sous une force

longitudinale constante (ISO/DIS 3501:2021)
Ta slovenski standard je istoveten z: prEN ISO 3501
ICS:
23.040.60 Prirobnice, oglavki in spojni Flanges, couplings and joints
elementi
oSIST prEN ISO 3501:2021 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 3501:2021
---------------------- Page: 2 ----------------------
oSIST prEN ISO 3501:2021
DRAFT INTERNATIONAL STANDARD
ISO/DIS 3501
ISO/TC 138/SC 5 Secretariat: NEN
Voting begins on: Voting terminates on:
2021-05-17 2021-08-09
Plastics piping systems — Mechanical joints between
fittings and pressure pipes — Test method for resistance to
pull-out under constant longitudinal force

Systèmes de canalisations en plastique — Assemblages mécaniques entre raccords et tubes sous pression

— Méthode d'essai de résistance à l'arrachement sous une force longitudinale constante

ICS: 23.040.60
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 3501:2021(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. ISO 2021
---------------------- Page: 3 ----------------------
oSIST prEN ISO 3501:2021
ISO/DIS 3501:2021(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2021

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 3501:2021
ISO/DIS 3501:2021(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Principle ........................................................................................................................................................................................................................ 1

5 Test parameters and requirements .................................................................................................................................................. 1

6 Apparatus ..................................................................................................................................................................................................................... 2

7 Test pieces ................................................................................................................................................................................................................... 3

8 Procedure..................................................................................................................................................................................................................... 4

9 Test report ................................................................................................................................................................................................................... 4

Annex A (normative) Test parameters ............................................................................................................................................................... 5

© ISO 2021 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 3501:2021
ISO/DIS 3501:2021(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www .iso .org/ patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to the

World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/

iso/ foreword .html.

This document was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves

for the transport of fluids, Subcommittee SC 5, General properties of pipes, fittings and valves of plastic

materials and their accessories – Test methods and basic specifications.

This third edition cancels and replaces the second edition (ISO 3501:2015), which has been technically

revised.
The main changes compared to the previous edition are as follows:
— the reference to leakage has been removed from the test report;
— editorial changes have been introduced.
Any feedb
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.