EN ISO 12215-4:2018
(Main)Small craft - Hull construction and scantlings - Part 4: Workshop and manufacturing (ISO 12215-4:2002)
Small craft - Hull construction and scantlings - Part 4: Workshop and manufacturing (ISO 12215-4:2002)
This part of ISO 12215 specifies workshop conditions, material storage and handling, and requirements for the manufacturing of the craft. It applies to small craft with a hull length ( LH) according to ISO 8666 of up to 24 m.
This part of ISO 12215 does not cover health and safety requirements.
Kleine Wasserfahrzeuge - Rumpfbauweise und Dimensionierung - Teil 4: Werkstatt und Fertigung (ISO 12215-4:2002)
Petits navires - Construction de coques et échantillons - Partie 4: Ateliers de construction et fabrication (ISO 12215-4:2002)
La présente partie de l'ISO 12215 spécifie, dans les ateliers de construction, les conditions de stockage et de maniement des matériaux, ainsi que des exigences relatives à la fabrication du bateau. Elle est applicable aux petits navires de longueur de coque ( LH ) inférieure ou égale à 24 m, conformément à l'ISO 8666.
La présente partie de l'ISO 12215 ne traite pas des exigences d'hygiène et de sécurité.
Mala plovila - Konstrukcija trupa in zahtevane lastnosti - 4. del: Izdelava (ISO 12215-4:2002)
Ta del standarda ISO 12215 določa pogoje in zahteve glede delavnice, skladiščenja materialov in ravnanja z njimi ter izdelave plovil. Uporablja se za mala plovila z dolžino trupa (LH) do 24 m v skladu s standardom ISO 8666.
Ta del standarda ISO 12215 ne zajema zdravstvenih in varnostnih zahtev.
OPOMBA: Osnovni razlog za pripravo tega dela standarda ISO 12215 je, da pogoji v delavnici pomembno vplivajo na kratkoročne in dolgoročne mehanske lastnosti plovila za rekreacijo ter da opredelitev zahtevanih lastnosti v skladu s standardom ISO 12215-5 temelji na pogojih, primernih za uporabljene materiale in postopek izdelave.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Mala plovila - Konstrukcija trupa in zahtevane lastnosti - 4. del: Izdelava (ISO 12215-4:2002)Kleine Wasserfahrzeuge - Rumpfbauweise und Dimensionierung - Teil 4: Werkstatt und Fertigung (ISO 12215-4:2002)Petits navires - Construction de coques et échantillons - Partie 4: Ateliers de construction et fabrication (ISO 12215-4:2002)Small craft - Hull construction and scantlings - Part 4: Workshop and manufacturing (ISO 12215-4:2002)47.080ýROQLSmall craft47.020.10Ladijski trupi in njihovi konstrukcijski elementiHulls and their structure elementsICS:Ta slovenski standard je istoveten z:EN ISO 12215-4:2018SIST EN ISO 12215-4:2018en,fr,de01-december-2018SIST EN ISO 12215-4:2018SLOVENSKI
STANDARDSIST EN ISO 12215-4:20021DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN ISO 12215-4
September
t r s z ICS
v yä r z r Supersedes EN ISO
s t t s wæ vã t r r tEnglish Version
Small craft æ Hull construction and scantlings æ Part
vã Petits navires æ Construction de coques et échantillons æ Kleine Wasserfahrzeuge æ Rumpfbauweise und Dimensionierung æ Teil
vã Werkstatt und Fertigung This European Standard was approved by CEN on
s x April
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN ISO
s t t s wæ vã t r s z ESIST EN ISO 12215-4:2018
Relationship between this European Standard and the Essential Requirements of Directive 2013/53/EU aimed to be covered . 4
Relationship between this European Standard and the Essential Requirements of Directive 2013/53/EU aimed to be covered This European standard has been prepared under a Commission’s standardization request M/542 C(2015) 8736 final to provide one voluntary means of conforming to Essential Requirements of Directive 2013/53/EU. Once this standard is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of the scope of this standard, a presumption of conformity with the corresponding Essential Requirements of that Directive and associated EFTA regulations. Table ZA.1 — Correspondence between this European Standard and Annex I of Directive 2013/53/EU Essential Requirements of Directive 2013/53/EU Clause(s)/sub-clause(s) of this EN Remarks/Notes Annex I, Part A, 3.1 - Structure All clauses
This standard only specifies workshop conditions and storage and handling processes to ensure that scantling determination set out in part 5 of ISO 12215 is based on conditions that are appropriate for the material used and the manufacturing processes applied for watercraft construction.
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European Standard is maintained in the list published in the Official Journal of the European Union. Users of this standard should consult frequently the latest list published in the Official Journal of the European Union. WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of this standard.
Reference numberISO 12215-4:2002(E)© ISO 2002
INTERNATIONAL STANDARD ISO12215-4First edition2002-05-01Small craft — Hull construction
and scantlings — Part 4: Workshop and manufacturing Petits navires — Construction de coques et échantillons — Partie 4: Ateliers de construction et fabrication
ISO 12215-4:2002(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2002 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.ch Web
www.iso.ch Printed in Switzerland
ii © ISO 2002 – All rights reserved
ISO 12215-4:2002(E) © ISO 2002 – All rights reserved iii Contents Page Foreword.iv 1 Scope.1 2 Normative references.1 3 Fibre-reinforced plastics (FRP) boat production.1 4 Metal craft production, steel and aluminium.6 5 Aluminium craft production, specific requirements.8 6 Wooden boat production.9 7 Boat production using other materials.10 8 Qualification of personnel.10 9 Final inspection.10 10 Conformity assurance.11
ISO 12215-4:2002(E) iv © ISO 2002 – All rights reserved
Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part of ISO 12215 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 12215-4 was prepared by Technical Committee ISO/TC 188, Small craft. ISO 12215 consists of the following parts, under the general title Small craft — Hull construction and scantlings: Part 1: Materials: Thermosetting resins, glass-fibre reinforcement, reference laminate Part 2: Materials: Core materials for sandwich construction, embedded materials Part 3: Materials: Steel, aluminium alloys, wood, other materials Part 4: Workshop and manufacturing Part 5: Design pressures, design stresses, scantling determination Part 6: Structural arrangements and details
INTERNATIONAL STANDARD ISO 12215-4:2002(E) © ISO 2002 – All rights reserved 1 Small craft — Hull construction and scantlings — Part 4: Workshop and manufacturing 1 Scope This part of ISO 12215 specifies workshop conditions, material storage and handling, and requirements for the manufacturing of the craft. It applies, to small craft with a (LH) length according to ISO 8666 of up to 24 m. This part of ISO 12215 does not cover health and safety requirements. NOTE The underlying reason for preparing this part of ISO 12215 is that workshop conditions have a significant influence on the mechanical short- and long-term properties of recreational craft and that the scantling determination according to ISO 12215-5 is based on conditions that are appropriate for the material used as well as the manufacturing process applied. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of ISO 12215. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 12215 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 8666:—1), Small craft — Principal data ISO 12215-1:2000, Small craft — Hull construction and scantlings — Part 1: Materials: Thermosetting resins, glass-fibre reinforcement, reference laminate ISO 12215-3:2002, Small craft — Hull construction and scantlings — Part 3: Materials: Steel, aluminium alloys, wood, other materials 3 Fibre-reinforced plastics (FRP) boat production 3.1 Workshop conditions 3.1.1 General The buildings used for production and storage shall be of suitable construction, and equipped to provide the environment specified by the material manufacturer or supplier.
1) To be published. SIST EN ISO 12215-4:2018
ISO 12215-4:2002(E) 2 © ISO 2002 – All rights reserved
To minimize contamination or impairment of the laminate, the production area shall be separate from the storage area and, wherever practicable, the various manufacturing processes shall be carried out in separate sections. The workshop and equipment shall be properly maintained and kept in a clean condition, substantially free from debris, surplus material, and equipment that is not essential for the production process. 3.1.2 Temperature and humidity Where a conventional manual lay-up or spray-up process is used, the moulding shop temperature shall be maintained within the limits specified by the resin manufacturer during lay-up and curing periods. Should the temperature vary outside the specified limits, the boat builder shall establish with the resin manufacturer that the resulting laminate will meet the requirements upon which scantlings and design are based. The relative humidity in the moulding shop shall be maintained within the l
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.