EN ISO 6847:2013

Welding consumables - Deposition of a weld metal pad for chemical analysis (ISO 6847:2013)

ISO 6847:2013 specifies the procedure to be used for deposition of a weld metal pad for chemical analysis. ISO 6847:2013 applies to deposition of a weld metal pad by use of covered electrodes, wire electrodes for gas shielded metal arc welding, tubular cored electrodes for gas shielded metal arc welding and for non-gas shielded metal arc welding, tubular cored rods for gas tungsten arc welding, and wire-flux combinations for submerged arc welding. ISO 6847:2013 is applicable to welding consumables for non-alloy and fine grain steels, high strength steels, creep-resisting steels, stainless and heat-resisting steels, nickel and nickel alloys, and copper and copper alloys.

Schweißzusätze - Auftragung von Schweißgut zur Bestimmung der chemischen Zusammensetzung (ISO 6847:2013)

Diese Internationale Norm legt das Verfahren zum Auftragen des Schweißgutes zum Ermitteln der chemischen Zusammensetzung fest. Diese Internationale Norm gilt für die Herstellung eines Schweißgutblockes durch umhüllte Stabelektroden, Drahtelektroden zum Metall-Schutzgasschweißen, Fülldrahtelektroden zum Metall-Schutzgasschweißen und für selbstschützendes Metall-Lichtbogenschweißen, Füllstäbe für Wolfram-Schutzgasschweißen und Draht-Pulver-Kombinationen für Unterpulverschweißen. Diese Internationale Norm gilt für Zusätze zum Schweißen von unlegierten Stählen, Feinkornstählen, hochfesten Stählen, warmfesten Stählen, nichtrostenden und hitzebeständigen Stählen, Nickel und Nickellegierungen sowie Kupfer und Kupferlegierungen.

Produits consommables pour le soudage - Exécution d'un dépôt de métal fondu pour l'analyse chimique (ISO 6847:2013)

L'ISO 6847:2013 spécifie le mode opératoire à utiliser pour réaliser un dépôt de soudure pour l'analyse chimique. L'ISO 6847:2013 est applicable à un bloc de métal fondu déposé à l'aide d'électrodes enrobées, des fils-électrodes pour le soudage à l'arc sous protection gazeuse, de fils fourrés pour le soudage à l'arc avec et sans protection gazeuse, de baguettes fourrées pour le soudage à l'arc avec électrode de tungstène ainsi que de couples fils-flux pour le soudage à l'arc sous flux. L'ISO 6847:2013 est également applicable aux produits consommables pour le soudage des aciers non alliés et à grains fins, des aciers à haute limite d'élasticité, des aciers résistant au fluage, des aciers inoxydables et réfractaires, du nickel et des alliages de nickel, du cuivre et des alliages de cuivre.

Dodajni materiali za varjenje - Izdelava čistih varov za kemijsko analizo (ISO 6847:2013)

Ta mednarodni standard določa postopek, ki se uporabi za izdelavo čistih varov za kemijsko analizo. Ta mednarodni standard se uporablja za izdelavo čistih varov z oplaščenimi elektrodami, žičnimi elektrodami za obločno varjenje v zaščitnih plinih, polnjenimi žicami za obločno varjenje v zaščitnih plinih in obločno varjenje brez zaščite, polnjenimi palicami za argonsko varjenje in kombinacijo žic za obločno varjenje pod praškom. Ta mednarodni standard se uporablja za dodajne materiale za varjenje nelegiranih in drobnozrnatih jekel, visokotrdnostnih jekel, proti lezenju odpornih jekel, nerjavnih in ognjeodpornih jekel, niklja in nikljevih zlitin ter bakra in bakrovih zlitin.

General Information

• Status: Withdrawn
• Publication Date: 18-Jun-2013
• Withdrawal Date: 15-Sep-2020
• ICS: 25.160.20 - Welding consumables
• Technical Committee: CEN/TC 121 - Welding
• Drafting Committee: CEN/TC 121/WG 3 - Welding consumables
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 16-Sep-2020
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Ref Project: SIST EN ISO 6847:2013 - Welding consumables - Deposition of a weld metal pad for chemical analysis (ISO 6847:2013)

Relations

• Replaces: EN ISO 6847:2001 - Welding consumables - Deposition of a weld metal pad for chemical analysis (ISO 6847:2000)
• Effective Date: 26-Jun-2013
• Replaced By: EN ISO 6847:2020 - Welding consumables - Deposition of a weld metal pad for chemical analysis (ISO 6847:2020)
• Effective Date: 23-Sep-2020

Standards Content (Sample)

SLOVENSKI STANDARD
01-december-2013
1DGRPHãþD
SIST EN ISO 6847:2002
'RGDMQLPDWHULDOL]DYDUMHQMH,]GHODYDþLVWLKYDURY]DNHPLMVNRDQDOL]R,62

Welding consumables - Deposition of a weld metal pad for chemical analysis (ISO
6847:2013)
Schweißzusätze - Auftragung von Schweißgut zur Bestimmung der chemischen
Zusammensetzung (ISO 6847:2013)
Produits consommables pour le soudage - Exécution d'un dépôt de métal fondu pour
l'analyse chimique (ISO 6847:2013)
Ta slovenski standard je istoveten z: EN ISO 6847:2013
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 6847
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2013
ICS 25.160.20 Supersedes EN ISO 6847:2001
English Version
Welding consumables - Deposition of a weld metal pad for
chemical analysis (ISO 6847:2013)
Produits consommables pour le soudage - Exécution d'un Schweißzusätze - Auftragung von Schweißgut zur
dépôt de métal fondu pour l'analyse chimique (ISO Bestimmung der chemischen Zusammensetzung (ISO
6847:2013) 6847:2013)
This European Standard was approved by CEN on 21 April 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6847:2013: E
worldwide for CEN national Members.

Contents Page
Foreword .3
Foreword
This document (EN ISO 6847:2013) has been prepared by Technical Committee IIW “International Institute of
Welding” in collaboration with Technical Committee CEN/TC 121 “Welding and allied processes” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2013, and conflicting national standards shall be withdrawn
at the latest by December 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 6847:2001.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 6847:2013 has been approved by CEN as EN ISO 6847:2013 without any modification.

INTERNATIONAL ISO
STANDARD 6847
Third edition
2013-06-15
Welding consumables — Deposition of
a weld metal pad for chemical analysis
Produits consommables pour le soudage — Exécution d’un dépôt de
métal fondu pour l’analyse chimique
Reference number
ISO 6847:2013(E)
©
ISO 2013
ISO 6847:2013(E)
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved

ISO 6847:2013(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Base metal . 1
3.1 Type . 1
3.2 Dimensions . 1
3.3 Surface condition . 1
4 Method for preparing the weld metal pad . 2
4.1 Drying of the welding consumables . 2
4.2 Welding position . 2
4.3 Type of current . 2
4.4 Welding conditions . 2
4.5 Welding method . 2
5 Weld metal pad size . 3
6 Sampling . 4
S
...