EN ISO 10140-1:2010
(Main)Acoustics - Laboratory measurement of sound insulation of building elements - Part 1: Application rules for specific products (ISO 10140-1:2010)
Acoustics - Laboratory measurement of sound insulation of building elements - Part 1: Application rules for specific products (ISO 10140-1:2010)
ISO 10140-1:2010 specifies test requirements for building elements and products, including detailed requirements for preparation, mounting, operating and test conditions, as well as applicable quantities and additional test information to be reported.
Akustik - Messung der Schalldämmung von Bauteilen im Prüfstand - Teil 1: Anwendungsregeln für bestimmte Produkte (ISO 10140-1:2010)
Dieser Teil der ISO 10140 legt Prüfanforderungen für Bauteile und Produkte, einschließlich der ausführlichen
Anforderungen an die Vorbereitung, Befestigung, die Betriebs- und die Prüfbedingungen sowie anwendbare
Größen und zusätzlich in den Prüfbericht aufzunehmende Angaben fest. Die allgemeinen Vorgehensweisen
für die Messung der Luftschall- und der Trittschalldämmung sind in ISO 10140-2 bzw. ISO 10140-3 enthalten.
Acoustique - Mesurage en laboratoire de l'isolation acoustique des éléments de construction - Partie 1: Règles d'application pour produits particuliers (ISO 10140-1:2010)
L'ISO 10140-1:2010 spécifie les exigences d'essai relatives aux éléments et produits de construction, y compris les exigences détaillées pour la préparation, le montage et les conditions de fonctionnement et d'essai, ainsi que les grandeurs applicables et les informations supplémentaires relatives aux rapports d'essai.
Akustika - Laboratorijsko merjenje zvočne izolirnosti gradbenih elementov - 1. del: Pravila uporabe za določene izdelke (ISO 10140-1:2010)
Ta del ISO 10140 določa preskusne zahteve za gradbene elemente in izdelke, vključno z podrobnimi zahtevami za pripravljalne, namestitvene, obratovalne in preskusne pogoje ter prav tako z ustreznimi količinami in dodatnimi informacijami o preskušanju za poročanje. Splošni postopki za ukrepe izolirnosti pred zvokom v zraku in udarnim zvokom so podani v ISO 10140-2 in ISO 10140-3 v tem zaporedju.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2010
1DGRPHãþD
SIST EN 20140-10:1997
SIST EN ISO 140-1:1998
SIST EN ISO 140-1:1998/A1:2005
SIST EN ISO 140-11:2005
SIST EN ISO 140-16:2006
SIST EN ISO 140-3:1997
SIST EN ISO 140-3:1997/A1:2005
SIST EN ISO 140-6:1999
SIST EN ISO 140-8:1998
$NXVWLND/DERUDWRULMVNRPHUMHQMH]YRþQHL]ROLUQRVWLJUDGEHQLKHOHPHQWRYGHO
3UDYLODXSRUDEH]DGRORþHQHL]GHONH ,62
Acoustics - Laboratory measurement of sound insulation of building elements - Part 1:
Application rules for specific products (ISO 10140-1:2010)
Akustik - Messung der Schalldämmung von Gebäudeteilen im Prüfstand - Teil 1:
Anwendungsregeln für bestimmte Produkte (ISO 10140-1:2010)
Acoustique - Détermination de l'isolation acoustique des éléments de construction -
Partie 1: Codes d'essai (ISO 10140-1:2010)
Ta slovenski standard je istoveten z: EN ISO 10140-1:2010
ICS:
91.120.20 $NXVWLNDYVWDYEDK=YRþQD Acoustics in building. Sound
L]RODFLMD insulation
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 10140-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2010
ICS 91.120.20 Supersedes EN 20140-10:1992, EN ISO 140-1:1997, EN
ISO 140-11:2005, EN ISO 140-16:2006, EN ISO 140-
3:1995, EN ISO 140-6:1998, EN ISO 140-8:1997
English Version
Acoustics - Laboratory measurement of sound insulation of
building elements - Part 1: Application rules for specific products
(ISO 10140-1:2010)
Acoustique - Mesurage en laboratoire de l'isolation Akustik - Messung der Schalldämmung von Gebäudeteilen
acoustique des éléments de construction - Partie 1: Règles
im Prüfstand - Teil 1: Anwendungsregeln für bestimmte
d'application pour produits particuliers (ISO 10140-1:2010) Produkte (ISO 10140-1:2010)
This European Standard was approved by CEN on 14 August 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10140-1:2010: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 10140-1:2010) has been prepared by Technical Committee ISO/TC 43 "Acoustics" in
collaboration with Technical Committee CEN/TC 126 “Acoustic properties of building elements and of
buildings” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by March 2011, and conflicting national standards shall be withdrawn at
the latest by March 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 20140-10:1992, EN ISO 140-3:1995, EN ISO 140-1:1997,
EN ISO 140-11:2005, EN ISO 140-6:1998, EN ISO 140-16:2006, EN ISO 140-8:1997.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 10140-1:2010 has been approved by CEN as a EN ISO 10140-1:2010 without any
modification.
INTERNATIONAL ISO
STANDARD 10140-1
First edition
2010-09-01
Acoustics — Laboratory measurement of
sound insulation of building elements —
Part 1:
Application rules for specific products
Acoustique — Mesurage en laboratoire de l'isolation acoustique des
éléments de construction —
Partie 1: Règles d'application pour produits particuliers
Reference number
ISO 10140-1:2010(E)
©
ISO 2010
ISO 10140-1:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
ISO 10140-1:2010(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 General .1
4 Structure of application rules for specific products.2
Annex A (normative) Walls — Airborne sound insulation.3
Annex B (normative) Doors — Airborne sound insulation.5
Annex C (normative) Windows — Airborne sound insulation .6
Annex D (normative) Glazing — Airborne sound insulation.8
Annex E (normative) Small technical elements — Airborne sound insulation .11
Annex F (normative) Floors — Airborne and impact sound insulation .15
Annex G (normative) Acoustical linings — Improvement of airborne sound insulation .16
Annex H (normative) Floor coverings — Improvement of impact sound insulation .20
Annex I (normative) Shutters — Airborne sound insulation.28
Bibliography.32
ISO 10140-1:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10140-1 was prepared by Technical Committee ISO/TC 43, Acoustics, Subcommittee SC 2, Building
acoustics.
This first edition of ISO 10140-1, together with ISO 10140-2, ISO 10140-3, ISO 10140-4 and ISO 10140-5,
cancels and replaces ISO 140-1:1997, ISO 140-3:1995, ISO 140-6:1998, ISO 140-8:1997, ISO 140-10:1991,
ISO 140-11:2005 and ISO 140-16:2006, which have been technically revised.
It also incorporates the Amendments ISO 140-1:1997/Amd.1:2004 and ISO 140-3:1995/Amd.1:2004.
ISO 10140 consists of the following parts, under the general title Acoustics — Laboratory measurement of
sound insulation of building elements:
⎯ Part 1: Application rules for specific products
⎯ Part 2: Measurement of airborne sound insulation
⎯ Part 3: Measurement of impact sound insulation
⎯ Part 4: Measurement procedures and requirements
⎯ Part 5: Requirements for test facilities and equipment
iv © ISO 2010 – All rights reserved
ISO 10140-1:2010(E)
Introduction
ISO 10140 (all parts) concerns laboratory measurement of the sound insulation of building elements (see
Table 1).
This part of ISO 10140 specifies the application rules for specific elements and products, including specific
requirements for preparation, mounting, operating and test conditions. ISO 10140-2 and ISO 10140-3 contain
the general procedures for airborne and impact sound insulation measurements, respectively, and refer to
ISO 10140-4 and ISO 10140-5 where appropriate. For elements and products without a specific application
rule described in this part of ISO 10140, it is possible to apply ISO 10140-2 and ISO 10140-3. ISO 10140-4
contains basic measurement techniques and processes. ISO 10140-5 contains the requirements for test
facilities and equipment. For the structure of ISO 10140 (all parts), see Table 1.
ISO 10140 (all parts) was created to improve the layout for laboratory measurements, ensure consistency and
simplify future changes and additions regarding mounting conditions of test elements in laboratory and field
measurements. It is intended for ISO 10140 (all parts) to present a well-written and arranged format for
laboratory measurements.
It is intended to update this part of ISO 10140 with application rules for other products. It is also intended to
incorporate ISO 140-18 into ISO 10140 (all parts).
ISO 10140-1:2010(E)
Table 1 — Structure and contents of ISO 10140 (all parts)
Relevant part Main purpose, contents and use Detailed content
of ISO 10140
It indicates the appropriate test procedure for
ISO 10140-1 Appropriate references to ISO 10140-2 and
elements and products. For certain types of
ISO 10140-3 and product-related, specific and
element/product, it can contain additional and
additional instructions on:
more specific instructions about quantities and
⎯ specific quantities measured;
test element size and about preparation,
⎯ size of test element;
mounting and operating conditions. Where no
⎯ boundary and mounting conditions;
specific details are included, the general
⎯ conditioning, testing and operating conditions;
guidelines according to ISO 10140-2 and
⎯ additional specifics for test report.
ISO 10140-3.
It gives a complete procedure for airborne sound
ISO 10140-2
⎯ Definitions of main quantities measured
insulation measurements according to
⎯ General mounting and boundary conditions
ISO 10140-4 and ISO 10140-5. For products
⎯ General measurement procedure
without specific application rules, it is sufficien
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.