EN ISO 15792-3:2011

Welding consumables - Test methods - Part 3: Classification testing of positional capacity and root penetration of welding consumables in a fillet weld (ISO 15792-3:2011)

ISO 15792-3:2011 specifies the preparation and assessment of fillet weld test pieces for conformity assessment of positional usability and root penetration requirements for consumables classification standards for welding non-alloy and fine grain steels, low alloy steels, stainless steels, and nickel base alloys.
ISO 15792-3:2011 does not specify acceptance requirements.

Schweißzusätze - Prüfverfahren - Teil 3: Prüfung zur Einteilung der Schweißzusätze nach ihrer Eignung für Schweißpositionen und Wurzeleinbrand an Kehlnähten (ISO 15792-3:2011)

Dieser Teil von ISO 15792 legt die Herstellung von Kehlnahtprüfstücken und die Bewertung der Prüfergebnisse im Hinblick auf die Übereinstimmung mit den Anforderungen an die Eignung zum Schweißen in verschiedenen Positionen und an die Wurzelerfassung nach den Einteilungsnormen für Schweißzusätze zum Schweißen von unlegierten und Feinkornstählen, niedriglegierten Stählen, nichtrostenden Stählen und Nickellegierungen fest.
Dieser Teil von ISO 15792 legt keine Anforderungen für die Bewertung fest.

Produits consommables pour le soudage - Méthodes d'essai - Partie 3: Évaluation de l'aptitude au soudage en position et de la pénétration en racine des produits consommables pour les soudures d'angle (ISO 15792-3:2011)

L'ISO 15792-3:2011 spécifie la préparation et l'évaluation des pièces d'essai en soudure d'angle pour déterminer la conformité aux exigences relatives à l'aptitude au soudage en position et à la pénétration en racine des normes de classification des électrodes et des fils d'apport pour le soudage à l'arc des aciers au carbone-manganèse, des aciers faiblement alliés, des aciers inoxydables et des alliages à base de nickel.
L'ISO 15792-3:2011 ne spécifie pas les exigences d'acceptation.

Dodajni materiali za varjenje - Preskusne metode - 3. del: Preskušanje primernosti dodajnih materialov za varjenje v legah in prevaritev korena pri kotnih varih (ISO 15792-3:2011)

Ta del ISO 15792 določa pripravo in ocenjevanje preskušancev kotnih varov za ocenjevanje skladnosti zahtev za uporabnost elektrod in žic za obločno varjenje za varjenje ogljikovo-manganovih jekel, malolegiranih jekel, nerjavnih jekel in zlitin na osnovi niklja. Ta del ISO 15792 ne določa zahtev za sprejemljivost.

General Information

• Status: Published
• Publication Date: 14-May-2011
• Withdrawal Date: 29-Nov-2011
• ICS: 25.160.20 - Welding consumables
• Technical Committee: CEN/TC 121 - Welding
• Drafting Committee: CEN/TC 121/WG 3 - Welding consumables
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 15-May-2011
• Completion Date: 15-May-2011
• Ref Project: SIST EN ISO 15792-3:2012 - Welding consumables - Test methods - Part 3: Classification testing of positional capacity and root penetration of welding consumables in a fillet weld (ISO 15792-3:2011)

Relations

• Replaces: EN ISO 15792-3:2008 - Welding consumables - Test methods - Part 3: Classification testing of positional capacity and root penetration of welding consumables in a fillet weld (ISO 15792-3:2000 including Cor 1:2006)
• Effective Date: 21-May-2011

Standards Content (Sample)

SLOVENSKI STANDARD
01-januar-2012
1DGRPHãþD
SIST EN ISO 15792-3:2008
Dodajni materiali za varjenje - Preskusne metode - 3. del: Preskušanje primernosti
dodajnih materialov za varjenje v legah in prevaritev korena pri kotnih varih (ISO
15792-3:2011)
Welding consumables - Test methods - Part 3: Classification testing of positional
capacity and root penetration of welding consumables in a fillet weld (ISO 15792-3:2011)
Schweißzusätze - Prüfverfahren - Teil 3: Prüfung zur Einteilung der Schweißzusätze
nach ihrer Eignung für Schweißpositionen und Wurzeleinbrand an Kehlnähten (ISO
15792-3:2011)
Produits consommables pour le soudage - Méthodes d'essai - Partie 3: Évaluation de
l'aptitude au soudage en position et de la pénétration en racine des produits
consommables pour les soudures d'angle (ISO 15792-3:2011)
Ta slovenski standard je istoveten z: EN ISO 15792-3:2011
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 15792-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2011
ICS 25.160.20 Supersedes EN ISO 15792-3:2008
English Version
Welding consumables - Test methods - Part 3: Classification
testing of positional capacity and root penetration of welding
consumables in a fillet weld (ISO 15792-3:2011)
Produits consommables pour le soudage - Méthodes
d'essai - Partie 3: Évaluation de l'aptitude au soudage en
position et de la pénétration en racine des produits
consommables pour les soudures d'angle (ISO 15792-
3:2011)
This European Standard was approved by CEN on 14 May 2011.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15792-3:2011: E
worldwide for CEN national Members.

Contents Page
Foreword .3

Foreword
This document (EN ISO 15792-3:2011) has been prepared by Technical Committee ISO/TC 44 "Welding and
allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding” the secretariat of which is
held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by November 2011, and conflicting national standards shall be withdrawn
at the latest by November 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15792-3:2008.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 15792-3:2011 has been approved by CEN as a EN ISO 15792-3:2011 without any
modification.
INTERNATIONAL ISO
STANDARD 15792-3
Second edition
2011-05-15
Welding consumables — Test methods —
Part 3:
Classification testing of positional
capacity and root penetration of welding
consumables in a fillet weld
Produits consommables pour le soudage — Méthodes d'essai —
Partie 3: Évaluation de l'aptitude au soudage en position et de la
pénétration en racine des produits consommables pour les soudures
d'angle
Reference number
ISO 15792-3:2011(E)
©
ISO 2011
ISO 15792-3:2011(E)
©  ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved

ISO 15792-3:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 15792-3 was prepared by Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee
SC 3, Welding consumables.
This second edition cancels and replaces the first edition (ISO 15792-3:2000). It also incorporates the
Technical Corrigendum ISO 15792-3:2000/Cor.1:2006.
ISO 15792 consists of the following parts, under the general title Welding consumables — Test methods:
⎯ Part 1: Test methods for all-weld metal test specimens in steel, nickel and nickel alloys
⎯ Part 2: Preparation of single-run and two-run technique test specimens in steel
⎯ Part 3: Classification testing of positional capacity and root penetration of welding consumables in a fillet
weld
Requests for official interpretations of any aspect of this part of ISO 15792 should be directed to the
Secretariat of ISO/TC 44/SC 3 via your national standards body. A complete listing of these bodies can be
found at www.iso.org.
ISO 15792-3:2011(E)
Introduction
This part of ISO 15792 specifies the preparation and assessment of fillet weld test piec
...