EN ISO 22553-15:2023

Paints and varnishes - Electro-deposition coatings - Part 15: Permeate residues (ISO 22553-15:2022)

This document specifies a test method for estimating the influence of jetting liquids from the rinsing process after electro-deposition coating (permeate residues) on a coating.
It applies to electro-deposition coatings for automotive industries and other general industrial applications, e.g. chiller units, consumer products, radiators, aerospace, agriculture.

Beschichtungsstoffe - Elektrotauchlacke - Teil 15: Permeatrückstände (ISO 22553-15:2022)

Peintures et vernis - Peintures d'électrodéposition - Partie 15: Résidus de perméat (ISO 22553-15:2022)

Le présent document spécifie une méthode d'essai pour estimer l'influence des liquides de projection provenant du procédé de rinçage après l’application par électrodéposition (résidus de perméat) sur un revêtement.
Il s’applique aux peintures d'électrodéposition destinées aux industries automobiles et autres applications industrielles générales, par exemple unités frigorifiques, biens de consommation, radiateurs, aérospatiale, agriculture.

Barve in laki - Elektrodepozicijski premazi - 15. del: Ostanki permeata (ISO 22553-15:2022)

Ta dokument določa preskusno metodo za ocenjevanje vpliva brizganja tekočin pri postopku
izpiranja po nanosu elektrodepozicijskega premaza (ostanki permeata) na premaz. Uporablja se za elektrodepozicijske premaze za avtomobilsko industrijo in drugo splošno industrijsko uporabo (npr. ohlajevalne enote, potrošniški izdelki, radiatorji, v aeronavtiki, kmetijstvu).

General Information

• Status: Published
• Publication Date: 29-Aug-2023
• ICS: 87.040 - Paints and varnishes
• Technical Committee: CEN/TC 139 - Paints and varnishes
• Drafting Committee: CEN/TC 139 - Paints and varnishes
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 30-Aug-2023
• Due Date: 17-Jun-2025
• Completion Date: 30-Aug-2023
• Ref Project: SIST EN ISO 22553-15:2023 - Paints and varnishes - Electro-deposition coatings - Part 15: Permeate residues (ISO 22553-15:2022)

Standards Content (Sample)

SLOVENSKI STANDARD
01-december-2023
Barve in laki - Elektrodepozicijski premazi - 15. del: Ostanki permeata (ISO 22553-
15:2022)
Paints and varnishes - Electro-deposition coatings - Part 15: Permeate residues (ISO
22553-15:2022)
Beschichtungsstoffe - Elektrotauchlacke - Teil 15: Permeatrückstände (ISO 22553-
15:2022)
Peintures et vernis - Peintures d'électrodéposition - Partie 15: Résidus de perméat (ISO
22553-15:2022)
Ta slovenski standard je istoveten z: EN ISO 22553-15:2023
ICS:
87.040 Barve in laki Paints and varnishes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 22553-15
EUROPEAN STANDARD
NORME EUROPÉENNE
August 2023
EUROPÄISCHE NORM
ICS 87.040
English Version
Paints and varnishes - Electro-deposition coatings - Part
15: Permeate residues (ISO 22553-15:2022)
Peintures et vernis - Peintures d'électrodéposition - Beschichtungsstoffe - Elektrotauchlacke - Teil 15:
Partie 15: Résidus de perméat (ISO 22553-15:2022) Permeatrückstände (ISO 22553-15:2022)
This European Standard was approved by CEN on 24 August 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 22553-15:2023 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
The text of ISO 22553-15:2022 has been prepared by Technical Committee ISO/TC 35 "Paints and
varnishes” of the International Organization for Standardization (ISO) and has been taken over as
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2024, and conflicting national standards
shall be withdrawn at the latest by February 2024.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 22553-15:2022 has been approved by CEN as EN ISO 22553-15:2023 without any
modification.
INTERNATIONAL ISO
STANDARD 22553-15
First edition
2022-09
Paints and varnishes — Electro-
deposition coatings —
Part 15:
Permeate residues
Peintures et vernis — Peintures d'électrodéposition —
Partie 15: Résidus de perméat
Reference number
ISO 22553-15:2022(E)
ISO 22553-15:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
ISO 22553-15:2022(E)
Contents Page
Foreword .iv
Introduction .v
1 S c op e . 1
2 Nor m at i ve r ef er enc e s . 1
3 Terms and definitions . 1
4 P r i nc iple . 2
5 Apparatus and test equipment . 2
6 Te s t p a nel s .3
7 Number of determinations . 3
8 P r o c e du re .3
8.1 C oating of the test panels . 3
8. 2 Bl ank t e st . 4
8.3 G eneral of test substances . . 4
9 Ev a luat ion . 4
10 Add it ion a l t e s t s . 5
11 Marking of the test result .5
12 P r e c i s ion . 5
13 Te s t r ep or t . 5
Bibliography . 6
iii
ISO 22553-15:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee
SC 9, General test methods for paints and varnishes.
A list of all parts in the ISO 22553 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
ISO 22553-15:2022(E)
Introduction
During the curing of the electro-deposition coating, residues from the rinsing process after electro-
deposition coating (permeate residues) can lead to deteriorations such as colour changes and changes
of the surface of the electro-deposition coat. The test method described in this document specifies a
test method for estimating the influence of jetting liquids on a coating.
v
INTERNATIONAL STANDARD ISO 22553-15:2022(E)
Paints and varnishes — Electro-deposition coatings —
Part 15:
Permeate residues
1 S cope
This document specifies a test method for estimating the influence of jetting liquids from the rinsing
process after electro-deposition coating (permeate residues) on a coating.
It applies to electro-deposition coatings for automotive industries and other general industrial
applications, e.g. chiller units, consumer products, radiators, aerospace, agriculture.
2 Normat ive references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 1514, Paints and varnishes — Standard panels for testing
ISO 1520, Paints and varnishes — Cupping test
ISO 4618, Paints and varnishes — Terms and definitions
ISO 4628-1:2016, Paints and varnishes — Evaluation of degradation of coatings — Designation of quantity
and size of defects, and of intensity of uniform changes in appearance — Part 1: General introduction and
designation system
ISO 13076, Paints and varnishes — Lighting and procedure for visual assessments of coatings
ISO 22553-1, Paints and varnishes — Electro-deposition coatings — Part 1: Vocabulary
ISO 23321, Solvents for paints and varnishes — Deminera
...