EN ISO 8739:1997

Grooved pins - Full-length parallel grooved, with pilot (ISO 8739:1997)

Zylinderkerbstifte mit Einführende (ISO 8739:1997)

Diese Internationale Norm beschreibt die Eigenschaften von Zylinderkerbstiften mit Einführende aus Stahl oder aus austenitischem nichtrostendem Stahl, mit 3 gleichmäßig verteilten Längskerben auf der Außenfläche und einem Einführende zur Erleichterung des Einbaus. Die Kerbstifte haben einen Nenndurchmesser von 1,5 mm bis einschließlich 25 mm.

Goupilles cannelées à cannelures constantes sur toute la longueur débouchantes, à bout pilote (ISO 8739:1997)

La présente Norme internationale prescrit les caractéristiques des goupilles cannelées à bout pilote en acier ou en acier inoxydable austénitique, à trois cannelures constantes sur toute leur longueur, débouchantes d'un côté et régulièrement espacées, de diamètre nominal, d1, de 1,5 mm à 25 mm inclus. Le matériau refoulé de chaque côté des cannelures forme un renflement dont le diamètre d2, supérieur au diamètre nominal d1, permet un ajustement serré de ces goupilles cannelées lorsqu'elles sont emmanchées en force dans un trou de diamètre de perçage égal au diamètre nominal de la goupille d1 (voir article 4).

Zasekani zatiči z brazdami enake globine po vsej dolžini in z valjasto končino (ISO 8739:1997)

General Information

• Status: Published
• Publication Date: 31-Oct-1997
• ICS: 21.060 - Fasteners
• Technical Committee: CEN/TC 185 - Threaded and nonthreaded mechanical fasteners and accessories
• Drafting Committee: CEN/TC 185 - Threaded and nonthreaded mechanical fasteners and accessories
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Start Date: 04-Feb-2008
• Completion Date: 04-Feb-2008
• Ref Project: SIST EN ISO 8739:2001 - Grooved pins - Full-length parallel grooved, with pilot (ISO 8739:1997)

Relations

• Revised: prEN ISO 8739 - Fasteners - Parallel grooved pins, with pilot point - Full-length diamond grooves (ISO/DIS 8739:2023)
• Effective Date: 19-Jan-2023

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Zylinderkerbstifte mit Einführende (ISO 8739:1997)Goupilles cannelées a cannelures constantes sur toute la longueur débouchantes, a bout pilote (ISO 8739:1997)Grooved pins - Full-length parallel grooved, with pilot (ISO 8739:1997)21.060.50Pins, nailsICS:Ta slovenski standard je istoveten z:EN ISO 8739:1997SIST EN ISO 8739:2001en01-julij-2001SIST EN ISO 8739:2001SLOVENSKI
STANDARD
AReference numberISO 8739:1997(E)INTERNATIONALSTANDARDISO8739Second edition1997-11-01Grooved pins — Full-length parallelgrooved, with pilotGoupilles cannelées à cannelures constantes sur toute la longueurdébouchantes, à bout piloteSIST EN ISO 8739:2001

ISO 8739:1997(E)©
ISO 1997All rights reserved. Unless otherwise specified, no part of this publication may be reproducedor utilized in any form or by any means, electronic or mechanical, including photocopying andmicrofilm, without permission in writing from the publisher.International Organization for StandardizationCase postale 56 · CH-1211 Genève 20 · [e-mail].400c=ch; a=400net; p=iso; o=isocs; s=centralPrinted in SwitzerlandiiForewordISO (the International Organization for Standardization) is a worldwidefederation of national standards bodies (ISO member bodies). The work ofpreparing International Standards is normally carried out through ISOtechnical committees. Each member body interested in a subject for whicha technical committee has been established has the right to be representedon that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISOcollaborates closely with the International Electrotechnical Commission(IEC) on all matters of electrotechnical standardization.Draft International Standards adopted by the technical committees arecirculated to the member bodies for voting. Publication as an InternationalStandard requires approval by at least 75 % of the member bodies castinga vote.International Standard ISO 8739 was prepared by Technical CommitteeISO/TC 2, Fasteners.This second edition cancels and replaces the first edition (ISO 8739:1986),which has been technically revised.SIST EN ISO 8739:2001

INTERNATIONAL STANDARD
© ISOISO 8739:1997(E)1Grooved pins — Full-length parallel grooved, with pilot1
ScopeThis International Standard specifies the characteristics of full-length parallel grooved pins, made of steel oraustenitic stainless steel, with pilot which have three equally spaced grooves impressed longitudinally on theirexterior surface and a pilot to facilitate insertion, with nominal diameter, d1, from 1,5 mm to 25 mm inclusive.The displaced material to each side of the grooves forming an expanded diameter d2 which is larger than thenominal diameter d1 will cause a non-positive locking fit when these grooved pins are forced into a drilled holeequal to the nominal diameter d1 (see clause 4).2
Normative referencesThe following standards contain provisions which, through reference in this text, constitute provisions of thisInternational Standard. At the time of publication, the editions indicated were valid. All standards are subjectto revision, and parties to agreements based on this International Standard are encouraged to investigate thepossibility of applying the most recent editions of the standards indicated below.
...