iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 13157:2004+A1:2009

(Main)

Cranes - Safety - Hand powered cranes

Cranes - Safety - Hand powered cranes

This European Standard specifies requirements for the following hand powered lifting equipment defined in clause 3:
   Hand chain blocks;
   Lever hoists;
   Jaw winches;
   Hand powered trolleys supporting lifting machines;
   Drum winches;
   Pulley blocks and deflection pulley.
The significant hazards covered by this European Standard are identified in clause 4.
This European Standard does not cover hazards related to the lifting of persons.
This standard does not specify the additional requirements for:
-   use in ambient temperature outside the range of - 10°C to + 50°C,
-   hand powered lifting equipment in direct contact with food stuffs or pharmaceuticals requiring a high level of cleanliness for hygiene reasons;
-   hazards resulting from handling specific hazardous materials (e.g. explosives, hot molten masses, radiating materials);
-   hazards caused by operation in an explosive atmosphere.
This European Standard is applicable to hand powered lifting equipment, which are manufactured after the date of approval by CEN of this standard.

Krane - Sicherheit - Handbetriebene Krane

Dieses Europäische Dokument legt Anforderungen für die in Abschnitt 3 definierten und nachfolgend aufge-führten handbetriebenen Krane fest:
-   Handkettenzüge;
-   Hebelzüge;
-   Klemmbackenwinden;
-   handbetriebene Fahrwerke, die Hebezeuge tragen;
-   Trommelwinden;
-   Flaschenzüge und Umlenkrollen.
Die von diesem Europäischen Dokument behandelten signifikanten Gefährdungen sind in Abschnitt 4 identifiziert.
Dieses Europäische Dokument behandelt nicht Gefährdungen, die in Bezug auf das Heben von Personen entstehen.
Dieses Dokument legt nicht die zusätzlichen Anforderungen für die folgenden Anwendungen fest:
-   Einsatz bei Umgebungstemperaturen außerhalb des Bereiches von 10 °C bis 50 °C;
-   handbetriebene Krane in direktem Kontakt mit Lebensmitteln oder pharmazeutischen Erzeugnissen, die aus hygienischen Gründen einen hohen Grad an Sauberkeit erfordern;
-   Gefährdungen durch die Handhabung spezifischer gefährlicher Werkstoffe (z. B. Sprengstoffe, feuer-flüssige Massen, strahlende Werkstoffe);
-   Gefährdungen durch Betrieb in explosiver Atmosphäre.
Dieses Europäische Dokument gilt für handbetriebene Hebezeuge, die nach dem Datum der Annahme dieses Dokuments durch das CEN gebaut wurden.

Appareils de levage à charge suspendue - Sécurité - Appareils de levage à bras

Dvigala - Varnost - Dvigala na ročni pogon

General Information

Status
Published
Publication Date
11-Aug-2009
ICS
53.020.20 - Cranes
Technical Committee
CEN/TC 147 - Cranes - Safety
Drafting Committee
CEN/TC 147 - Cranes - Safety
Current Stage
9092 - Decision on results of review/2YR ENQ - revise - Review Enquiry
Completion Date
31-Mar-2021
Directive
2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
98/37/EC - Machinery
Mandate
M/079 - Mandate to CEN and CENELEC for standardization in the field of machines
M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
Ref Project
SIST EN 13157:2004+A1:2009 - Cranes - Safety - Hand powered cranes

Relations

Merged From
EN 13157:2004 - Cranes - Safety - Hand powered lifting equipment
Effective Date
19-Jan-2023
Merged From
EN 13157:2004/AC:2008 - Cranes - Safety - Hand powered lifting equipment
Effective Date
19-Jan-2023

Buy Standard

EN 13157:2004+A1:2009EN 13157:2004+A1:2009
PreviousNext
Standard
EN 13157:2004+A1:2009
English language
58 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Krane - Sicherheit - Handbetriebene KraneAppareils de levage à charge suspendue - Sécurité - Appareils de levage à brasCranes - Safety - Hand powered cranes53.020.20DvigalaCranesICS:Ta slovenski standard je istoveten z:EN 13157:2004+A1:2009SIST EN 13157:2004+A1:2009en01-november-2009SIST EN 13157:2004+A1:2009SLOVENSKI
STANDARD



SIST EN 13157:2004+A1:2009



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13157:2004+A1
August 2009 ICS 53.020.20 Supersedes EN 13157:2004English Version
Cranes - Safety - Hand powered cranes
Appareils de levage à charge suspendue - Sécurité - Appareils de levage à bras
Krane - Sicherheit - Handbetriebene Krane This European Standard was approved by CEN on 22 October 2003 and includes Corrigendum 1 issued by CEN on 8 October 2008 and Amendment 1 approved by CEN on 16 July 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13157:2004+A1:2009: ESIST EN 13157:2004+A1:2009



EN 13157:2004+A1:2009 (E) 2 Contents Foreword .3Introduction .41Scope .52Normative references .53Terms and definitions .63.1General definitions .63.2Definitions for hand chain blocks .73.3Definitions for lever hoists .83.4Definitions for jaw winches . 103.5Definitions for hand powered trolleys supporting lifting machines . 103.6Definitions for drum winches . 123.7Definitions for pulley blocks and deflection pulley . 134List of significant hazards . 155Safety requirements and/or measures . 215.1Hand chain blocks . 215.2Lever hoists . 235.3Jaw winches . 285.4Hand powered trolleys supporting lifting machines . 305.5Drum winches .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 13557:2024(Main)
Cranes - Control devices and control stations
SIST EN 13557:2024

This document specifies health and safety design requirements for control devices and control stations and their operating positions for all types of cranes.
Specific requirements for particular types of cranes are given in the appropriate European Standard for the particular crane type (see Annex B).
This document does not deal with noise hazards because these are dealt with in safety standards for specific types of cranes. It also does not address the design of the cabin with regard to its sound insulation properties.
This document covers specific hazards which could occur during the use of control devices and control stations. It does not cover hazards which could occur during transport, construction, modification, de-commissioning, or disposal. The hazards covered by this document are identified in Annex A.
This document is not applicable to cranes manufactured before the date of its publication.

  • Draft
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13001-3-6:2018+A1:2021(Main)
Cranes - General design - Part 3-6: Limit states and proof of competence of machinery - Hydraulic cylinders
SIST EN 13001-3-6:2018+A1:2021

This document is to be used together with the other generic parts of EN 13001 series of standards, see Annex E, as well as pertinent crane type product EN standards, and as such they specify general conditions, requirements and methods to, by design and theoretical verification, prevent mechanical hazards of hydraulic cylinders that are part of the load carrying structures of cranes. Hydraulic piping, hoses and connectors used with the cylinders are not within the scope of this document, as well as cylinders made from other material than carbon steel.
NOTE 1   Specific requirements for particular crane types are given in the appropriate European product standards, see Annex E.
The significant hazardous situations and hazardous events that could result in risks to persons during intended use are identified in Annex F. Clauses 4 to 7 of this document provide requirements and methods to reduce or eliminate these risks:
a)   exceeding the limits of strength (yield, ultimate, fatigue);
b)   elastic instability (column buckling).
NOTE 2   EN 13001-3-6 deals only with the limit state method in accordance with EN 13001-1.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13001-3-5:2016+A1:2021(Main)
Cranes - General design - Part 3-5: Limit states and proof of competence of forged and cast hooks
SIST EN 13001-3-5:2016+A1:2021

This European Standard is to be used together with EN 13001-1 and EN 13001-2 and, as such, they specify general conditions, requirements and methods to prevent by design and theoretical verification, mechanical hazards in crane hooks.
This European Standard covers the following parts of hooks and types of hooks:
-   bodies of any type of hooks made of steel forgings;
-   machined shanks of hooks with a thread/nut suspension.
Principles of this European Standard can be applied to machined shanks of hooks in general. However, stress concentration factors relevant to designs not given in this standard would have to be determined and applied.
NOTE 1   Cast hooks and plate hooks, which are those, assembled of one or several parallel parts of rolled steel plates, are not covered in this European Standard.
The following is a list of significant hazardous situations and hazardous events that could result in risks to persons during normal use and foreseeable misuse. Clauses 4 to 8 of this document are necessary to reduce or eliminate the risks associated with the following hazards:
a)   exceeding the limits of strength (yield, ultimate, fatigue);
b)   exceeding temperature limits of material.
The requirements of this European Standard are stated in the main body of the document and are applicable to forged hook designs in general.
The commonly used hook body and shank designs listed in Annexes A, B and F are only examples and should not be referred to as requirements of this European Standard. Annex I gives guidance for the selection of a hook size, where a hook body is in accordance with Annex A or B. The selection of hook form is not limited to those shown in Annexes A and B.
This European Standard is applicable to cranes, which are manufactured after the date of approval of this European Standard by CEN, and serves as a reference base for product standards of particular crane types.
NOTE 2   This part of EN 13001 deals only with the limit state method in accordance with EN 13001-1.
FprA1:
Add after 1st paragraph the following sentence:
"
It has to be used together with the other generic parts of EN 13001 series of standards, see Annex L.
".
Replace in 2nd paragraph the 1st list item with:
"
-   bodies of any type of hooks made of steel forgings or steel castings, including stainless steel;".
Replace NOTE 1 with:
"
NOTE 1   Plate hooks, which are those, assembled of one or several parallel parts of rolled steel plates, are not covered in this document.".
In the 4th paragraph, replace the 1st list item with:
"
a)   exceeding the limits of yield strength, ultimate strength, fatigue strength, brittle fracture;".
Replace the 5th paragraph with:
"The requirements of this document are stated in the main body of the document and are applicable to hook designs in general.".
After 4th paragraph, add the sentence:
"
The hazards covered by this document are identified by Annex M.
".

  • Standard
    92 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13852-3:2021(Main)
Cranes - Offshore cranes - Part 3: Light offshore cranes
SIST EN 13852-3:2021

This document applies to light offshore cranes including their supporting pedestals and structures.
NOTE   Supporting pedestal and structures such as columns and boom rests, are covered by this document to the extent where their main purpose is to support the crane.
This document is applicable to light offshore cranes, whose structures are made of steel, and fulfil all of the following characteristics:
-   maximum rated capacity 15 tonnes or maximum static load moment 3 000 kNm;
-   limitation for off-board lifting operation up to Hs = 2,0 m and wind speed 15 m/s (3 s gust);
-   maximum number of working cycles class U1 (C ≤ 3,15 × 104) according to EN 13001-1.
This document provides requirements for all significant hazards, hazardous situations and events relevant to light offshore cranes for lifting of goods and lifting of persons, when used as intended and under conditions foreseen by the risk assessment (see Clause 4).
This document is applicable to light offshore cranes, which are manufactured after the date of approval by CEN of this document.
This document is not applicable for:
a)   transportation, assembly, disabling, scrapping, installation or erecting of the crane;
b)   any item attached to the hook, such as loads, non-fixed load lifting attachments, lifting accessories, baskets, carriers and containers;
c)   lifting operations in ambient temperatures below −20 °C;
d)   lifting operations in ambient temperatures above 45 °C;
e)   lifting operations involving more than one crane;
f)   accidental loads as result of collisions, earthquakes, explosions, etc., which are not covered by exceptional loads defined in Table B.7;
g)   emergency personnel rescue operations (except training);
h)   subsea lifting operations;
i)   general purpose offshore cranes (covered by EN 13852-1), floating cranes and motion compensated cranes.

  • Standard
    111 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13001-2:2021(Main)
Crane safety - General design - Part 2: Load actions
SIST EN 13001-2:2021

This document specifies load actions and load combinations for the calculation of load effects as basis for the proof of competence of a crane and its main components. It will be used together with the other generic parts of the EN 13001 series of standards, see Annex E. As such they specify conditions and requirements on design to prevent mechanical hazards of cranes and provide a method of verification of those requirements.
NOTE   Specific requirements for particular types of crane are given in the appropriate European product standards for the particular crane type, see Annex E.
The following is a list of significant hazardous situations and hazardous events that could result in risks to persons during normal use and reasonably foreseeable misuse. Clause 4 of this document provides means to reduce or eliminate the risks of mechanical failures due to the following:
a)   rigid body instability of the crane or its parts (tilting);
b)   exceeding the limits of strength (yield, ultimate, fatigue);
c)   elastic instability of the crane or its parts or components (buckling, bulging).
The hazards covered by this document are identified by Annex G.
This document is not applicable to cranes that are manufactured before the date of its publication as EN.

  • Standard
    75 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13586:2020(Main)
Cranes - Access
SIST EN 13586:2021

This document specifies design requirements for non-powered access installed on cranes.
NOTE 1 For other type of access, a requirement for information to be supplied is specified.
Slidable, retractable means of access are excluded from the scope, except movable hoop guards.
This document covers means of access to control stations and all access required for maintenance, certain erection and dismantling operations.
For those cranes which are intended to be erected and dismantled frequently to change their places of work, specific requirements for the access needed during these operations are not covered by this document and should be given in the appropriate European Standards for specific crane types.
Lighting of means of access is not covered by this document and should be given in the appropriate European Standards for specific crane types.
NOTE 2 Specific requirements for access on particular types of cranes are given in the appropriate European Standard for the particular crane type.
The requirements given in this document do not take into account the safety distances related to:
- guarding against hazard from moving parts;
- relative movement between crane and adjacent structure or the ground/floor;
- hazardous surface temperature;
- electrical equipment.
The significant hazards covered by this document are identified in Clause 4. This document is not applicable to cranes which are manufactured before the date of publication by CEN of this document.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 16851:2017+A1:2020(Main)
Cranes - Light crane systems
SIST EN 16851:2017+A1:2021

This document applies to:
-   light crane systems, either suspended or free-standing systems, where the rated capacity of any single lifting device is 4 t or less;
-   pillar and wall-mounted jib cranes, without an operator's cabin, whose rated capacity is 10 t or less and whose overturning load moment is 500 kNm or less.
NOTE   For illustration of crane types, see Annex B.
This document is not applicable to cranes covered by another product specific crane standard, e.g. EN 15011:2011+A1:2014 or EN 14985:2012.
This document is applicable to cranes and crane systems, whose structures are made of steel or aluminium, excluding aluminium structures containing welded joints.
This document gives requirements for all significant hazards, hazardous situations and events relevant to cranes, when used as intended and under conditions foreseen by the manufacturer (see Clause 4).
The specific hazards due to potentially explosive atmospheres, ionizing radiation, operation in electro-magnetic fields beyond the range of EN 61000 6 2:2016 and operation in pharmacy or food industry are not covered by this document.
This document does not cover hazards related to the lifting of persons.
This document is applicable to cranes, which are manufactured after the date of its publication by CEN as a European Standard.
This document is not applicable to cranes manufactured before the date of its publication.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 17076:2020(Main)
Tower cranes - Anti-collision systems - Safety requirements
SIST EN 17076:2021

This document specifies the requirements of anti-collision devices and systems installed on tower cranes (as defined in EN 14439) to avoid the risks of collision between several cranes in service, between a crane in use and fixed obstacles, and over prohibited zones.
It also specifies the requirements for working range limiting devices.
Anti-collision devices and systems and working range limiting devices according to this document are safety components.
It applies to anti-collision devices manufactured after the publication of this document.
NOTE   For anti-collision systems used to avoid the risk of collision with power lines, additional requirements might be necessary.
This document defines the safety characteristics and requirements of anti-collision devices and systems intended for installation on self-erecting tower cranes and tower cranes erected from parts.
In particular:
-   performance level;
-   information to be provided by the sensors installed on the crane;
-   operation, particularly in the event of failure, override and free jib slewing states of a crane;
-   type of communication between devices;
-   information for the crane operator and outside indicator.
It also specifies the requirements for marking the device or the system and the content of the instructions for use.
The significant hazards covered by this document are identified in Clause 4.
This document is not applicable to anti-collision devices and systems which are manufactured before the date of publication by CEN of this document.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15011:2020(Main)
Cranes - Bridge and gantry cranes
SIST EN 15011:2021

This document applies to bridge and gantry cranes able to travel by wheels on rails, runways or roadway surfaces, and to gantry cranes without wheels mounted in a stationary position.
NOTE Light crane systems (assembly of lifting devices, crane bridges, trolleys and tracks; wall-mounted, pillar and workshop jib cranes) are covered by EN 16851.
This document specifies requirements for all significant hazards, hazardous situations and events relevant to bridge and gantry cranes when used as intended and under conditions foreseen by the manufacturer (see Clause 4).
This document does not include requirements for the lifting of persons.
The specific hazards due to potentially explosive atmospheres, ionising radiation and operation in electromagnetic environment beyond the scope of EN 61000-6-2 are not covered by this document.
This document is applicable to bridge and gantry cranes manufactured after the date of its publication as a European standard.

  • Standard
    94 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12999:2020(Main)
Cranes - Loader cranes
SIST EN 12999:2020

This document specifies minimum requirements for design, calculation, examinations and tests of hydraulic powered loader cranes and their mountings on vehicles or static foundations.
This document applies to loader cranes designed to be installed on:
-   road vehicles, including trailers, with load carrying capability;
-   tractors (road or agricultural), where only a towed trailer has capability to carry goods;
-   demountable bodies to be carried by any of the above;
-   other types of carriers (e.g. separate loaders, crawlers, rail vehicles, non-seagoing vessels);
-   static foundations.
This document also applies to loader cranes equipped with special tools or interchangeable equipment (e.g. grapple, clamshell bucket, pallet clamp, etc.), as specified in the operator’s manual.
This document does not apply to loader cranes used on board sea going vessels or to articulated boom system cranes which are designed as total integral parts of special equipment such as forwarders.
The hazards covered by this document are identified in Clause 4.
This document does not cover hazards related to the lifting of persons.
NOTE   The use of cranes for lifting of persons can be subject to specific national regulations.
This document is not applicable to loader cranes manufactured before the publication of this document. For loader cranes designed before the publication of this document, the provisions concerning stress calculations in the version of EN 12999 that was valid at the time of their design, are still applicable.

  • Standard
    107 pages
    English language
    sale 10% off
    e-Library read for
    1 day