Nonwovens - Test methods - Part 3: Determination of tensile strength and elongation at break using the strip method (ISO 9073-3:2023)

This document specifies a test method for the determination of the breaking force and elongation of nonwovens using a strip method in conditioned or wet state. This test method describes two procedures, Option A (width of test specimen: 25 mm) and Option B (width of test specimen: 50 mm).
This document specifies methods using constant rate of specimen extension (CRE) tensile testers. Constant rate of loading (CRL) instruments is covered, for information, in ISO 2062:2009, Annex A, in recognition of the fact that these instruments are still in use and can be used by agreement.

Vliesstoffe - Prüfverfahren - Teil 3: Bestimmung der Höchstzugkraft und der Höchstzugkraftdehnung (ISO 9073‑3:2023)

Dieses Dokument legt ein Prüfverfahren zur Bestimmung der Höchstzugkraft und der Höchstzugkraftdehnung von vorbehandelten bzw. nassen Vliesstoffen in einem Streifenzugversuch fest. Dieses Prüfverfahren beschreibt zwei Verfahren, Option A (Breite der Messprobe: 25 mm) und Option B (Breite der Messprobe: 50 mm).
Dieses Dokument legt Verfahren unter Verwendung von Zugprüfgeräten mit konstanter Verformungsgeschwindigkeit (en: constant rate of specimen extension, CRE) fest. Geräte mit konstanter Lastgeschwindigkeit (en: constant rate of loading, CRL) werden in Anerkennung der Tatsache, dass diese Geräte weiterhin verwendet werden und nach Vereinbarung verwendet werden können, zu Informationszwecken in ISO 2062:2009, Anhang A, behandelt.
SICHERHEITSHINWEIS — Dieses Dokument erhebt nicht den Anspruch, eine vollständige Aufzählung von gegebenenfalls zutreffenden Sicherheitsproblemen zu beinhalten, die mit seiner Anwendung verbunden sind. Es liegt in der Verantwortung des Anwenders dieses Dokuments, geeignete Sicherheits- und Gesundheitsschutzmaßnahmen vorzusehen und im Vorfeld die Anwendbarkeit von einschränkenden Vorschriften zu klären. Es wird erwartet, dass die Person, die diese Prüfung durchführt, in allen Aspekten dieses Verfahrens umfassend geschult wurde.

Nontissés - Méthodes d'’essai - Partie 3: Détermination de la résistance à la traction et de l'allongement à la rupture par la méthode sur bande (ISO 9073-3:2023)

Le présent document spécifie une méthode d’essai pour la détermination de la force de rupture et de l’allongement des nontissés après conditionnement ou à l’état humide, par la méthode sur bande. Cette méthode d’essai décrit deux modes opératoires, nommés option A (épaisseur de l’éprouvette d’essai: 25 mm) et option B (épaisseur de l’éprouvette d’essai: 50 mm).
Le présent document spécifie des méthodes utilisant des appareils d’essai de traction à vitesse constante d’allongement (CRE) de l’éprouvette. À titre d’information, les appareils à gradient de force constant (GFC) sont couverts dans l’ISO 2062:2009, Annexe A, étant donné que ces instruments sont toujours utilisés et que leur utilisation peut faire l'objet d'un accord entre les parties intéressées.

Vlaknovine - Preskusne metode - 3. del: Ugotavljanje natezne trdnosti in pretržnega raztezka pri pretrganju s tračno metodo (ISO 9073-3:2023)

Vršenje vzdolžne sile na preskušanca določene dolžine in debeline pri konstantni hitrosti raztezanja. Določanje vrednosti za utržno trdnost in raztezek na podlagi ugotovljene krivulje sila-raztezek. V tem delu standarda ISO 9073 so določene zahteve za izpolnitev posebnih potreb vlakovin, ki so drugačne od zahtev, navedenih v standardu ISO 5081. Nanašajo se na a) drugačen postopek vzorčenja; b) konstantno hitrost raztezanja (100 mm/min).

General Information

Status
Published
Publication Date
20-Jun-2023
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
21-Jun-2023
Completion Date
21-Jun-2023

Relations

Buy Standard

Standard
EN ISO 9073-3:2023
English language
21 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-september-2023
Vlaknovine - Preskusne metode - 3. del: Ugotavljanje natezne trdnosti in
pretržnega raztezka pri pretrganju s tračno metodo (ISO 9073-3:2023)
Nonwovens - Test methods - Part 3: Determination of tensile strength and elongation at
break using the strip method (ISO 9073-3:2023)
Vliesstoffe - Prüfverfahren - Teil 3: Bestimmung der Höchstzugkraft und der
Höchstzugkraftdehnung (ISO 9073-3:2023)
Nontissés - Méthodes d'essai - Partie 3: Détermination de la résistance à la traction et de
l'allongement à la rupture par la méthode sur bande (ISO 9073-3:2023)
Ta slovenski standard je istoveten z: EN ISO 9073-3:2023
ICS:
59.080.30 Tkanine Textile fabrics
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 9073-3
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2023
EUROPÄISCHE NORM
ICS 59.080.30 Supersedes EN 29073-3:1992
English Version
Nonwovens - Test methods - Part 3: Determination of
tensile strength and elongation at break using the strip
method (ISO 9073-3:2023)
Nontissés - Méthodes d'¿essai - Partie 3: Détermination Vliesstoffe - Prüfverfahren - Teil 3: Bestimmung der
de la résistance à la traction et de l'allongement à la Höchstzugkraft und der Höchstzugkraftdehnung (ISO
rupture par la méthode sur bande (ISO 9073-3:2023) 9073-3:2023)
This European Standard was approved by CEN on 27 May 2023.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9073-3:2023 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 9073-3:2023) has been prepared by Technical Committee ISO/TC 38 "Textiles"
in collaboration with Technical Committee CEN/TC 248 “Textiles and textile products” the secretariat of
which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2023, and conflicting national standards
shall be withdrawn at the latest by December 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 29073-3:1992.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 9073-3:2023 has been approved by CEN as EN ISO 9073-3:2023 without any
modification.
INTERNATIONAL ISO
STANDARD 9073-3
Second edition
2023-06
Nonwovens — Test methods —
Part 3:
Determination of tensile strength and
elongation at break using the strip
method
Nontissés — Méthodes d’essai —
Partie 3: Détermination de la résistance à la traction et de
l’allongement à la rupture par la méthode sur bande
Reference number
ISO 9073-3:2023(E)
ISO 9073-3:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 9073-3:2023(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 4
5 Reagents and materials . 4
6 Apparatus . 5
6.1 Tensile testing machine (CRE or CRL) . 5
6.2 Clamps and jaw faces . 6
6.3 Container . 6
7 Conditioning . 6
8 Sampling . 6
8.1 General . 6
8.2 Laboratory sample . 7
8.3 Test specimens. 7
9 Preparation of specimens .7
9.1 General . 7
9.2 Dimensions . 7
9.3 Wet test specimens . 8
10 Preparation, calibration and verification of apparatus . 8
10.1 Tensile testing machine . 8
10.2 Clamping system . 8
10.3 Verification of the total operating system of the apparatus . 8
11 Procedure . 9
11.1 Gauge length . 9
11.2 Rate of extension . 9
11.3 Mounting of test specimens . 9
11.4 Operation . 10
11.5 Slippage . 10
11.6 Jaw breaks . 10
12 Calculation .10
12.1 Breaking force . 10
12.2 Measurement of apparent elongation . 11
12.3 For each testing situation . 11
13 Expression of results .11
14 Precision .11
15 Test report .11
Annex A (informative) Possible causes of low precision when strip tensile testing .13
Bibliography .14
iii
ISO 9073-3:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.