prEN ISO 14890
(Main)Conveyor belts - Specification for rubber- or plastics-covered conveyor belts of textile construction for general use (ISO/DIS 14890:2025)
Conveyor belts - Specification for rubber- or plastics-covered conveyor belts of textile construction for general use (ISO/DIS 14890:2025)
ISO 14890:2013 specifies requirements for rubber and/or plastics covered conveyor belting of textile construction for general surface use on flat or troughed idlers.
ISO 14890:2013 is not suitable or valid for light conveyor belts as described in ISO 21183-1.
Items that are not requirements of ISO 14890:2013, but need to be agreed between the manufacturer and the purchaser, as well as a list of the details intended to be supplied by the purchaser of belting with an enquiry are included in the annexes.
Fördergurte- Anforderungen an Textilfördergurte mit Gummi- oder Kunststoff-Deckplatten für allgemeine Anwendungen (ISO/DIS 14890:2025)
Courroies transporteuses - Spécification pour courroies transporteuses recouvertes de caoutchouc ou de plastique à structure textile, d'usage général (ISO/DIS 14890:2025)
L'ISO 14890:2013 spécifie les exigences relatives aux courroies à revêtement caoutchouc et/ou plastique, à structure textile, pour une utilisation générale de type «jour» sur des rouleaux plats ou en auge.
L'ISO 14890:2013 n'est pas applicable aux courroies transporteuses légères telles que décrites dans l'ISO 21183‑1.
Certains points, qui ne sont pas des exigences de l'ISO 14890:2013, mais nécessitent un accord entre le fabricant et l'acheteur, sont inclus dans une annexe, de même qu'une liste de détails à fournir par l'acheteur de courroie lors de la commande.
Naprave za kontinuirni transport - Zahteve za tračne transportne trakove iz tekstila z gumeno ali plastično oblogo za splošno uporabo (ISO/DIS 14890:2025)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2025
Naprave za kontinuirni transport - Zahteve za tračne transportne trakove iz tekstila
z gumeno ali plastično oblogo za splošno uporabo (ISO/DIS 14890:2025)
Conveyor belts - Specification for rubber- or plastics covered conveyor belts of textile
construction for general use (ISO/DIS 14890:2025)
Fördergurte- Anforderungen an Textilfördergurte mit Gummi oder Kunststoff-Deckplatten
für allgemeine Anwendungen (ISO/DIS 14890:2025)
Courroies transporteuses - Spécification pour courroies transporteuses recouvertes de
caoutchouc ou de plastique à structure textile, d'usage général (ISO/DIS
14890:2025)
Ta slovenski standard je istoveten z: prEN ISO 14890
ICS:
53.040.20 Deli za transporterje Components for conveyors
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
International
Standard
ISO/DIS 14890
ISO/TC 41/SC 3
Conveyor belts — Specification
Secretariat: SAC
for rubber- or plastics-covered
Voting begins on:
conveyor belts of textile
2025-02-13
construction for general use
Voting terminates on:
2025-05-08
Courroies transporteuses — Spécification pour courroies
transporteuses recouvertes de caoutchouc ou de plastique à
structure textile, d'usage général
ICS: 53.040.20
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 14890:2025(en)
DRAFT
ISO/DIS 14890:2025(en)
International
Standard
ISO/DIS 14890
ISO/TC 41/SC 3
Conveyor belts — Specification
Secretariat: SAC
for rubber- or plastics-covered
Voting begins on:
conveyor belts of textile
construction for general use
Voting terminates on:
Courroies transporteuses — Spécification pour courroies
transporteuses recouvertes de caoutchouc ou de plastique à
structure textile, d'usage général
ICS: 53.040.20
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2025
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: +41 22 749 01 11
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 14890:2025(en)
ii
ISO/DIS 14890:2025(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Designation . 2
4.1 Belting designation .2
4.2 Examples for ordering .3
5 Construction . 4
6 Length . 4
7 Width . 5
8 Rubber cover . 6
9 Tolerances on total belt thickness and cover thickness . 7
9.1 Tolerance on total belt thickness .7
9.2 Tolerance on cover thickness . .7
10 Transverse fabric joints in multi-ply belting . 7
10.1 General .7
10.2 Outer plies . .7
10.3 Inner plies .8
10.4 Adjacent plies and non-adjacent plies .8
10.5 Joints in the same ply .8
10.6 Mono-ply,duo-ply and solid woven belting .8
11 Longitudinal fabric joints in multi-ply belting and duo-ply belting . 8
11.1 Spacing of joints .8
11.2 Number of joints .8
12 Longitudinal fabric or carcass joints in solid woven and mono-ply belting . 8
13 Elongation . 8
14 Full thickness tensile strength . 8
15 Adhesion . 9
16 Troughability . . 9
17 Sampling . 10
18 Identification . 10
Annex A (informative) Items to be agreed between the manufacturer and purchaser .11
Annex B (informative) Helpful information to be supplied by the purchaser .12
Annex C (informative) Lateral drift —Straight running . 14
Bibliography .15
iii
ISO/DIS 14890:2025(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 41 Pulleys and belts (including veebelts),
Subcommittee SC 3,Conveyor belts .
This third edition cancels and replaces the second edition (ISO14890:2013), which has been technically
revised and minor editorial revised.
The main changes are as follows:
— Remove code letter G and its correspondent yarn of Glass from Table 1;
— Revise longitudinal joints numbers of Table 7;
— Include more tensile strength categories into Table 8 ;
A list of all parts in the ISO 14890 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s nationa
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.