EN 16728:2016

LPG equipment and accessories - Transportable refillable LPG cylinders other than traditional welded and brazed steel cylinders - Periodic inspection

This European Standard specifies procedures for periodic inspection and testing, for transportable refillable LPG cylinders with a water capacity from 0,5 l up to and including 150 l.
This European Standard is applicable to the following:
-   welded steel LPG cylinders manufactured to an alternative design and construction, see EN 14140 or equivalent standard;
-   welded aluminium LPG cylinders, see EN 13110 or equivalent standard;
-   composite LPG cylinders, see EN 14427 or equivalent standard;
-   over-moulded cylinders designed and manufactured according to EN 1442 or EN 14140, see Annex F.
NOTE   The requirements of RID/ADR take precedence over those of this Standard in the case of cylinders complying with that regulation, including pi marked cylinders.
This European Standard does not apply to cylinders permanently installed in vehicles.

Flüssiggas-Geräte und Ausrüstungsteile - Ortsbewegliche, wiederbefüllbare Flaschen für Flüssiggas (LPG), ausgenommen geschweißte und hartgelötete Stahlflaschen - Wiederkehrende Inspektion

Diese Europäische Norm legt Verfahren für die wiederkehrende Inspektion und Prüfung von ortsbeweglichen, wiederbefüll¬baren Flaschen für Flüssiggas (LPG) mit einem Fassungsraum von 0,5 l bis einschließlich 150 l fest.
Diese Europäische Norm gilt für:
-   geschweißte Flaschen aus Stahl für Flüssiggas (LPG), die mit alternativer Gestaltung und Konstruktion hergestellt wurden, siehe EN 14140 oder eine gleichwertige Norm;
-   geschweißte Flaschen aus Aluminium für Flüssiggas (LPG), siehe EN 13110 oder eine gleichwertige Norm;
-   Flüssiggasflaschen aus Verbundwerkstoff, siehe EN 14427 oder eine gleichwertige Norm;
-   umformte Flaschen, gestaltet und hergestellt nach EN 1442 oder EN 14140, siehe Anhang F.
ANMERKUNG   Für Flaschen, die den Vorschriften der/des RID/ADR entsprechen sowie für Flaschen mit der Kennzeichnung "pi", haben die in der/dem RID/ADR angegebenen Anforderungen Vorrang gegenüber den Anforderungen in der vorliegenden Norm.
Diese Europäische Norm gilt nicht für Flaschen, die dauerhaft in Fahrzeugen eingebaut sind.

Équipements pour GPL et leurs accessoires - Bouteilles transportables et rechargeables pour GPL autres que celles en acier soudé et brasé - Contrôle périodique

Cette Norme européenne spécifie des modes opératoires pour des contrôles et des essais périodiques pour des bouteilles pour GPL transportables et rechargeables d’une capacité en eau comprise entre 0,5 et 150 l.
Cette Norme s’applique aux éléments suivants :
-   bouteilles pour GPL, en acier soudé, fabriquées selon une conception et fabrication différentes, voir l'EN 14140 ou une Norme équivalente ;
-   bouteilles pour GPL, en aluminium soudé, voir l'EN 13110 ou une Norme équivalente ;
-   bouteilles pour GPL, en matériau composite, voir l'EN 14427 ou une Norme équivalente ;
-   bouteilles surmoulées conçues et fabriquées conformément à l'EN 1442 ou l'EN 14140, voir l'Annexe F.
La présente Norme européenne ne s’applique pas aux bouteilles installées en permanence dans des véhicules.

Oprema in pribor za utekočinjeni naftni plin (UNP) - Premične, ponovno polnljive plinske jeklenke za UNP, ki niso varjene in trdo spajkane - Periodična kontrola

Ta evropski standard določa postopke za periodične preglede in preskušanje premičnih, ponovno polnljivih jeklenk za utekočinjeni naftni plin (LPG) z vodno kapaciteto od 0,5 l do vključno 150 l.
Ta evropski standard se uporablja za:
– varjene jeklenke za LPG z alternativno zasnovo in konstrukcijo (glej EN 14140 ali enakovreden standard);
– varjene aluminijaste jeklenke za LPG (glej EN 13110 ali enakovredni standard);
– kompozitne jeklenke za LPG (glej EN 14427 ali enakovredni standard);
– prelite jeklenke, zasnovane in izdelane v skladu s standardom EN 1442 ali EN 14140 (glej dodatek F).
Ta evropski standard se ne uporablja za jeklenke, trajno nameščene v vozila.

General Information

• Status: Withdrawn
• Publication Date: 08-Mar-2016
• Withdrawal Date: 12-Jun-2018
• ICS: 23.020.30 - Pressure vessels, gas cylinders
• ICS: 23.020.35 - Gas cylinders
• Technical Committee: CEN/TC 286 - Liquefied petroleum gas equipment and accessories
• Drafting Committee: CEN/TC 286/WG 7 - Operational requirements - Transportable LPG cylinders and static LPG tanks
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 13-Jun-2018
• Directive: 2008/68/EC - Directve 2008/68/EC of the European Parliament and of the council of 24 September 2008 on the inland transport of the dangerous goods
• Directive: 94/55/EC - Transport of dangerous goods by road
• Directive: 96/49/EC - Transport of dangerous goods by rail
• Directive: 96/86/EC - Transport of dangerous goods by road (94/55/EC Dir. amendment)
• Directive: 96/87/EC - Transport of dangerous goods by rail (96/49/EC Dir. amendment)
• Mandate: M/086 - Mandate to CEN for standardization in the field of transport of dangerous goods
• Ref Project: SIST EN 16728:2016 - LPG equipment and accessories - Transportable refillable traditional LPG cylinders other than traditional welded and brazed steel cylinders - Periodic inspection

Relations

• Replaces: EN 1440:2008+A1:2012 - LPG equipment and accessories - Periodic inspection of transportable refillable LPG cylinders
• Effective Date: 08-Jun-2022
• Merged Into: EN 16728:2016+A1:2018 - LPG equipment and accessories - Transportable refillable LPG cylinders other than traditional welded and brazed steel cylinders - Periodic inspection
• Effective Date: 18-Jan-2023
• Amended By: EN 16728:2016+A1:2018/FprA2:2019 - LPG equipment and accessories - Transportable refillable LPG cylinders other than traditional welded and brazed steel cylinders - Periodic inspection
• Effective Date: 30-May-2018
• Amended By: EN 16728:2016/prA1 - LPG equipment and accessories - Transportable refillable LPG cylinders other than traditional welded and brazed steel cylinders - Periodic inspection
• Effective Date: 09-Nov-2016

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Flüssiggas-Geräte und Ausrüstungsteile - Ortsbewegliche, wiederbefüllbare Flaschen für Flüssiggas (LPG), ausgenommen geschweißte und hartgelötete Stahlflaschen - Wiederkehrende InspektionÉquipements pour GPL et leurs accessoires - Bouteilles transportables et rechargeables pour GPL autres que celles en acier soudé et brasé - Contrôle périodiqueLPG equipment and accessories - Transportable refillable traditional LPG cylinders other than traditional welded and brazed steel cylinders - Periodic inspection23.020.35Plinske jeklenkeGas cylindersICS:Ta slovenski standard je istoveten z:EN 16728:2016SIST EN 16728:2016en,fr,de01-junij-2016SIST EN 16728:2016SLOVENSKI
STANDARDSIST EN 1440:2008+A1:20121DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 16728
March
t r s x ICS
t uä r t rä u r Supersedes EN
s v v rã t r r z ªA sã t r s tEnglish Version
LPG equipment and accessories æ Transportable refillable LPG cylinders other than traditional welded and brazed steel cylinders æ Periodic inspection Équipements pour GPL et leurs accessoires æ Bouteilles transportables et rechargeables pour GPL autres que celles en acier soudß et brasß æ Contrôle pßriodique
FlüssiggasæGeräte und Ausrüstungsteile æ Ortsbeweglicheá wiederbefüllbare Flaschen für hartgelötete Stahlflaschen æ Wiederkehrende Inspektion This European Standard was approved by CEN on
t January
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey andUnited Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s x CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s x y t zã t r s x ESIST EN 16728:2016

Page European foreword . 4 Introduction . 5 1 Scope . 6 2 Normative references . 6 3 Terms and definitions . 7 4 Requirements for periodic inspection . 8 4.1 General . 8 4.2 Steel and aluminium cylinders . 8 4.3 Over-moulded cylinders . 8 4.4 Composite cylinders . 8 4.5 Rejected cylinders . 9 5 Inspections and tests . 10 5.1 General . 10 5.2 External visual inspection . 10 5.2.1 Preparation for external visual inspection. 10 5.2.2 Inspection procedure . 10 5.2.3 Rejection criteria . 11 5.3 Proof pressure test . 11 5.3.1 General . 11 5.3.2 Hydraulic proof pressure test. 11 5.3.3 Pneumatic proof test and leak test . 12 5.4 Check of the internal condition of the cylinder . 13 5.4.1 Welded aluminium and steel cylinders of alternative design and construction . 13 5.4.2 Check of the internal condition of composite cylinders . 14 5.5 Inspection of cylinder threads . 14 5.5.1 General . 14 5.5.2 Internal threads . 14 5.5.3 External threads . 15 5.5.4 Damaged threads . 15 5.6 Inspection of valves . 15 6 Final operations . 15 6.1 General . 15 6.2 Valving . 15 6.3 Tare mass . 15 6.4 Marking . 15 6.5 Purging . 16 7 Repair of cylinders . 16 8 Records . 16 Annex A (normative)
Specific requirements for external visual inspection for welded steel LPG cylinders in accordance with EN 14140 or equivalent standard . 17 A.1 General . 17 A.2 Procedure for establishing rejection criteria carbon steel cylinders . 17 A.3 Rejection criteria for stainless steel cylinders . 19 SIST EN 16728:2016

Specific requirements for external visual inspection of welded aluminium LPG cylinders . 22 Annex C (normative)
Specific requirements for visual inspection of composite LPG cylinders . 25 C.1 Establishment of rejection criteria . 25 C.1.1 General . 25 C.1.2 Procedure . 25 C.2 Examples of rejection criteria . 25 C.2.1 Cylinders without a metallic liner . 25 C.2.2 Cylinders with a metallic liner . 30 Annex D (informative)
Conditions for 15-year periodic inspection interval of welded steel cylinders manufactured before 1st January 2015 . 33 D.1 General . 33 D.2 Concept of control. 33 D.3 Conditions . 33 Annex E (informative)
Guidance on conditions for 10-year periodic inspection interval of composite cylinders . 35 Annex F (normative)
Specific Periodic inspection procedure for over-moulded cylinders (OMC) . 36 F.1 General . 36 F.1.1 Introduction. 36 F.1.2 Valve . 36 F.1.3 Marking and records . 36 F.2 Periodic inspection . 36 F.2.1 General . 36 F.2.2 External visual inspection . 37 F.2.2.1 General . 37 F.2.2.2 Sampling . 37 F.2.2.2.1 General . 37 F.2.2.2.2 Peeling and corrosion test . 37 F.2.2.2.3 Adhesion tests of the polyurethane material . 38 F.2.2.3 Test frequency . 38 F.2.3 Burst test . 38 F.2.4 Rejection criteria and annual production sampling . 38 F.2.5 Periodic inspection tests reports and records . 40 F.3 Lifetime . 40 Annex G (informative)
Example of
...