Abstract

This document specifies a method for determining the density of compacted fresh concrete both in the laboratory and in the field.
It may not be applicable to very stiff concrete which cannot be compacted by normal vibration.

Status
Not Published
Publication Date
10-Oct-2027
Current Stage
4020 - Submission to enquiry - Enquiry
Start Date
22-Oct-2026
Due Date
14-Aug-2026
Completion Date
22-Oct-2026

Buy Documents

prEN 12350-6 is a CEN draft in the EN 12350 series for testing fresh concrete. It specifies a method for determining the density of compacted fresh concrete in the laboratory and in the field, and it is aimed at users who need a consistent density result from a compacted sample.

What does prEN 12350-6 specify?

prEN 12350-6 specifies how to determine the density of compacted fresh concrete and how to report the result. The method uses a rigid, watertight container of known volume and mass, and it covers both sampling and calculation.

The document is organized into:

  • Scope
  • Normative references
  • Terms and definitions
  • Principle
  • Apparatus
  • Sampling
  • Procedure
  • Calculation of density
  • Test report
  • Precision
  • Annex A for calibration of the density container

The scope notes that prEN 12350-6 may not be applicable to very stiff concrete that cannot be compacted by normal vibration. That matters in practice because the method depends on achieving full compaction before weighing.

What are the key requirements of prEN 12350-6?

Clause 4 states the basic principle: fresh concrete is placed into a container with known volume, compacted, and then weighed. In practice, the density result depends on both correct compaction and an accurate container volume.

Sampling and preparation

Clause 6 requires the sample to be taken in accordance with EN 12350-1 and then re-mixed using the remixing container and shovel. This helps make the sample representative before the test begins.

Apparatus and measuring equipment

Clause 5 requires the common apparatus from EN 12350-1 and adds a density container, filling frame, compaction tools, balance or scales, and finishing tools. The balance or scales must have a maximum instrumental measurement uncertainty of 0,1 % of the mass, which matters because small weighing errors directly affect the calculated density.

Container calibration

Clause 7.1 and Annex A require calibration of the density container to obtain its volume, V. Annex A describes a water-filling method using a glass plate and gives the calculation based on the mass of water needed to fill the container. In practice, the container volume is not assumed - it is measured and recorded.

Filling and compaction

Clause 7.3 requires the container to be filled in as many layers as needed for full compaction, except for self-compacting concrete, which is filled in one operation. Clause 7.4 allows mechanical compaction with an internal vibrator or vibrating table, or hand compaction with a rod or bar. The key practical point is to compact enough to remove entrapped air, but not so much that segregation or loss of entrained air occurs.

Special handling for self-compacting concrete

Clause 7.4.1 states that self-compacting concrete is not mechanically or manually compacted during or after filling. That means the operator must fill the container without adding vibration or rodding, because the material is intended to flow and compact itself.

Surface finishing and weighing

Clauses 7.5 and 7.6 require the filled container to be struck off level, cleaned, and weighed to determine the total mass. This ensures the result reflects only the concrete and not excess material on the rim or outside of the container.

Density calculation and reporting

Clause 8 gives the density calculation from the mass of the empty container, the mass of the filled container, and the calibrated volume. Clause 9 requires the report to identify the standard, sample, test location, date, compaction method, calculated density, deviations from the method, and a technical declaration of compliance.

What changed in prEN 12350-6 from the previous edition?

prEN 12350-6 will supersede EN 12350-6:2019. The foreword states two significant technical changes:

  • editorial revisions
  • harmonization of maximum instrumental measurement uncertainty in the EN 12350 series for the same mass

Which standards are used with prEN 12350-6?

  • EN 12350-1 - provides the sampling requirements and the common apparatus used for fresh concrete testing.
  • ISO 5725-1 - provides the general principles and definitions for trueness and precision, which are referenced in the precision notes.
  • EN 206-1 - is cited for slump classes in the hand-compaction guidance and helps users relate the method to concrete consistence.

Who uses prEN 12350-6?

prEN 12350-6 is used by concrete testing laboratories, site inspectors, quality control staff, and engineers involved in concrete production and placement. It is relevant in both laboratory and field work where fresh concrete density is needed for acceptance checks, process control, or comparative testing. It also matters to buyers and specifiers who need a consistent test method for fresh concrete with a defined compaction procedure.

What does the prEN 12350-6 document contain?

The document contains a procedural test method, a normative calibration annex, a calculation formula, a test report checklist, and precision data. It also includes guidance on mechanical and hand compaction, surface levelling, and weighing. The precision section gives repeatability and reproducibility data for a specified density range and notes the conditions under which those values apply. Annex A gives the calibration procedure for the density container, including the water-filling method used to establish container volume.

Relations

Effective Date
12-Nov-2025

Buy Documents

Get Certified

Connect with accredited certification bodies for this standard

DIBt (Deutsches Institut für Bautechnik)

German Institute for Building Technology.

DAKKS Germany Verified

DIN CERTCO

DIN Group product certification.

DAKKS Germany Verified

Aboma Certification B.V.

Specialized in construction, metal, and transport sectors.

RVA Netherlands Verified

Sponsored listings

Frequently Asked Questions

prEN 12350-6 is a draft published by the European Committee for Standardization (CEN). Its full title is "Testing fresh concrete - Part 6: Density". This standard covers: This document specifies a method for determining the density of compacted fresh concrete both in the laboratory and in the field. It may not be applicable to very stiff concrete which cannot be compacted by normal vibration.

This document specifies a method for determining the density of compacted fresh concrete both in the laboratory and in the field. It may not be applicable to very stiff concrete which cannot be compacted by normal vibration.

prEN 12350-6 is classified under the following ICS (International Classification for Standards) categories: 91.100.30 - Concrete and concrete products. The ICS classification helps identify the subject area and facilitates finding related standards.

prEN 12350-6 has the following relationships with other standards: It is inter standard links to EN 12350-6:2019. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

prEN 12350-6 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


SLOVENSKI STANDARD
01-december-2026
Preskušanje svežega betona - 6. del: Gostota
Testing fresh concrete - Part 6: Density
Prüfung von Frischbeton - Teil 6: Frischbetonrohdichte
Essais pour béton frais - Partie 6 : Masse volumique
Ta slovenski standard je istoveten z: prEN 12350-6
ICS:
91.100.30 Beton in betonski izdelki Concrete and concrete
products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2026
ICS 91.100.30 Will supersede EN 12350-6:2019
English Version
Testing fresh concrete - Part 6: Density
Essais pour béton frais - Partie 6 : Masse volumique Prüfung von Frischbeton - Teil 6: Frischbetonrohdichte
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 104.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark,
Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye
and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
C O M I T É E U R O P É E N D E N O R M A L I S A T I O N
E U R O P Ä I S C H E S K O M I T E E F Ü R N O R M U N G
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12350-6:2026 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Principle . 4
5 Apparatus . 4
6 Sampling . 5
7 Procedure . 5
7.1 Calibration . 5
7.2 Mass of density container . 5
7.3 Filling the density container . 5
7.4 Compacting the concrete . 5
7.4.1 General. 5
7.4.2 Mechanical compaction . 6
7.4.3 Compacting by hand with compacting rod or bar . 6
7.5 Surface levelling . 6
7.6 Weighing . 6
8 Calculation of density . 6
9 Test report . 7
10 Precision . 7
Annex A (normative) Calibration of density container . 9
Bibliography . 10

European foreword
This document (prEN 12350-6:2026) has been prepared by Technical Committee CEN/TC 104 “Concrete
and related products”, the secretariat of which is held by SN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 12350-6:2019.
EN 12350-6:2019:
a) editorial revisions;
b) homogenization of maximum instrumental measurement uncertainty (EN 12350 series) for same
mass;
This document is one of a series on testing concrete.
EN 12350, Testing fresh concrete, consists in the following parts:
— Part 1: Sampling and common apparatus
— Part 2: Slump test
— Part 3: Vebe test
— Part 4: Degree of compactability
— Part 5: Flow table test
— Part 6: Density
— Part 7: Air content – Pressure methods
— Part 8: Self-compacting concrete – Slump-flow test
— Part 9: Self-compacting concrete – V-funnel test
— Part 10: Self-compacting concrete – L-box test
— Part 11: Self-compacting concrete – Sieve segregation test
— Part 12: Self-compacting concrete – J-ring test
— Part 13: Bleeding test – Static and pressure
— Part 14: Inverted cone flow time
— Part 15: Slump flow velocity
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
1 Scope
This document specifies a method for determining the density of compacted fresh concrete both in the
laboratory and in the field.
It may not be applicable to very stiff concrete which cannot be compacted by normal vibration.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 12350-1, Testing fresh concrete — Part 1: Sampling and common apparatus
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp/
— IEC Electropedia: available at https://www.electropedia.org/
4 Principle
Fresh concrete is compacted into a rigid and watertight container of known volume and mass and is then
weighed.
5 Apparatus
5.1 Common apparatus for fresh concrete testing.
The apparatus listed below for the execution of this test method shall be in accordance with the
specification given in EN 12350-1 and as specified below.
5.2 Density container, having the same specification and dimensions as the container specified in
EN 12350-1.
5.3 Filling frame, filling may be simplified by using a filling frame fitted tightly to the density container.
5.4 Means of compacting the concrete, which may be one of the following:
c) internal (poker) vibrator;
d) vibrating table;
e) compacting rod;
f) compacting bar.
5.5
...